WenmarOpen by Wenmar Pro

Service bulletins for the 2015 GMC Yukon

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

2691 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Bulletins, newest first
PIP5175B2017-08-15. Service bulletin. EQUIPMENT:MECHANICAL; POWER TRAIN:AUTOMATIC TRANSMISSION. This Preliminary Information communication provides information to the technician about vehicles that may have a delayed engagement into drive, shudder at a launch, or the transmission is slipping when shifting into 1st, 2nd, 3rd or 4th gears. This may be due to loose stator support to pump cover bolts causing a leak at the stator support to pump cover gasket. Technician will check for the bolts to be loose. If any of the bolts are loose or the gasket is misaligned or leaking, the transmission pump cover must be replaced and the 1234 clutch plates should be inspected for being distressed and repaired as needed.
PIP51962017-08-15. Service bulletin. POWER TRAIN:AXLE ASSEMBLY; SUSPENSION:MULTIPLE AXLE. This Preliminary Information communication provides information to the technician with the steps to diagnose and repair vehicles that may have a whine noise at highway speeds from the rear of the vehicle. If the technician has diagnosed the noise to be a rear axle related whine noise at highway speed, then use published Service Information "Symptoms - Rear Drive Axle". Technician should also compare the concern with a vehicle of the same build. If the noise level is deemed excessive check the vehicle build. Technician will replace the propeller shafts if needed.
PIT52832017-08-15. Service bulletin. EQUIPMENT:ELECTRICAL. This Preliminary Information communication provides information to the technician about vehicles that have a touchscreen that is inaccurate or that the display does not seem to respond with the desired operation when pressed. Technician will need to perform a touch screen calibration and re-evaluate the concern.
PIT52492017-08-15. Service bulletin. SERVICE BRAKES. This Preliminary Information communication advises the technician that there is a new DOT 3 brake fluid for the 2014 Silverado and Sierra 1500. Technician can order the new DOT 3 brake fluid from their parts department.
PIP4670D2017-08-15. Service bulletin. ELECTRICAL SYSTEM; ENGINE. This Preliminary Information communication provides information to the technician about a no start or another concern after swapping an Engine Control Module or other modules from one vehicle to another. The Global Architecture electrical system associated with these vehicles does not allow controller swaps between vehicles.
PIP5092A2017-08-15. Service bulletin. PARKING BRAKE:DRIVELINE. This Preliminary Information communication provides information to the technician about vehicles that a driveline noise or vibration at various speeds and operating conditions. Technician should be advised that the vehicle should always be restored to a factory configuration when diagnosing noise and vibration concerns.
PIP5089A2017-08-15. Service bulletin. ELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING. This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code C0569 that will not clear. Technician should be advised if there are any issues with the rotational position sensor, incremental position sensor, encoder motor, motor A or B circuits, rotational position sensor or incremental position sensor circuits when the transfer case control module attempts to determine location the location cannot be determined correctly.
PIP5175A2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING; WHEELS:LUGS/NUTS/BOLTS/STUDS; WHEELS; POWER TRAIN. This Preliminary Information communication provides information to the technician about vehicles that may have a delayed engagement into drive, shudder at a launch, or the transmission is slipping when shifting into 1st, 2nd, 3rd or 4th gears. This may be due to loose stator support to pump cover bolts causing a leak at the stator support to pump cover gasket. Technician will check for the bolts to be loose. If any of the bolts are loose or the gasket is misaligned or leaking, the transmission pump cover must be replaced and the 1234 clutch plates should be inspected for being distressed and repaired as needed.
PIT52622017-08-15. Service bulletin. EXTERIOR LIGHTING. This Preliminary Information communication advises the technician that while performing the Pre-Delivery Inspection, please make sure to check the front park halo ring lights for proper operation. The lights should be on steady with no flickering or erratic operation.
PIP51752017-08-15. Service bulletin. PARKING BRAKE; ENGINE AND ENGINE COOLING; WHEELS:LUGS/NUTS/BOLTS/STUDS; POWER TRAIN. This Preliminary Information communication provides information to the technician about vehicles that may have a delayed engagement into drive, shudder at a launch, or the transmission is slipping when shifting into 1st, 2nd, 3rd or 4th gears. This may be due to loose stator support to pump cover bolts causing a leak at the stator support to pump cover gasket. Technician will check for the bolts to be loose. If any of the bolts are loose or the gasket is misaligned or leaking, the transmission pump cover must be replaced and the 1234 clutch plates should be inspected for being distressed and repaired as needed.
PIT5241A2017-08-15. Service bulletin. ELECTRICAL SYSTEM: INTEGRATED TRAILER BRAKE CONTROL. This Preliminary Information communication provides information to the technician about customers that may request the factory Integrated Trailer Brake Controller Regular Production Option Code (JL1) be installed on their Full-Size Pickup or SUV when the vehicle was not ordered with the option. Dealer should advise the customer it cannot be added to the vehicle.
PIC5491E2017-08-15. Service bulletin. ELECTRICAL SYSTEM; ELECTRICAL SYSTEM:SOFTWARE. This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. After the vehicle has powered down, remove power to the OnStar module for five minutes. After the power has been removed for five minutes, if the OnStar system is working release the vehicle. If the OnStar system is still inoperative continue with published Service Information diagnostics. Technician may need to contact General Motors Technical Assistance Center depending on the STID, Station ID, or OnStar Customer Identifier.
PIC3011H2017-08-15. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. This Preliminary Information communication provides information to the technician about vehicles that have the OnStar system does not respond properly to some numbers and/or voice commands. Dealer should direct the customer to review the operational characteristics in the OnStar Users Guide.
PIT52592017-08-15. Service bulletin. EQUIPMENT. This Preliminary Information communication advises the technician that the door striker cover will be shipped with the vehicle from the assembly plant. Technician is to make sure the rounded side of the cover is positioned towards the outboard side of the vehicle.
PIT52572017-08-15. Service bulletin. ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician with diagnostic tips about vehicles that have one or more passive entry buttons, located on the outside door handles, are not working or are intermittently working. Technician should ensure the key FOB works within approximately 1 meter (3? 3?) of the door handle where the passive entry button is being operated. Also ensure the customer may not have had their finger or thumb completely on the door handle button. Be advised in cold weather (below 32° Fahrenheit or 0° Celsius), ice may form between the door handle and the button during car washes or thaw / freeze cycles. If a door handle switch is suspected to be defective, it can be component tested.
PIT5245A2017-08-15. Service bulletin. EQUIPMENT:APPLIANCE:AIR CONDITIONER; ENGINE AND ENGINE COOLING. This Preliminary Information communication provides information to the technician about vehicles that the blower motor may be noisy or vibrate when running. This concern will only occur when the temperatures is below 32 degrees Fahrenheit and if the blower motor is removed while still cold, ice may be found on the blower motor cage. This concern could be caused by water leaking or snow ingestion into the Heater-Vent-Air Conditioning case. Technician is to perform normal water testing diagnostics while the Heater-Vent-Air Conditioning is running, looking for water leaking past the plenum cover. If water is leaking past the cover remove the cover and install a 12x12 snow resistant screen to the fresh air intake. Reseal and install the plenum cover cap using Kent air dry sealer or equivalent.
PIT4943C2017-08-15. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL; FUEL SYSTEM, GASOLINE; SERVICE BRAKES, HYDRAULIC. This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0442. Technician will need to review Techlink article from May 2013 titled "Using the Evaporative Emissions System Tester" Technician will need to follow these steps to help diagnose the issue. First after the P0442 has been verified do not disturb any of the fuel system components. The technician now can use the scan tool to close the Evaporative Emissions System. If possible change the tank pressure sensor units from inch_H2O to milimeter_Hg for better resolution. Now the vehicle can be stared to monitor the tank pressure sensor output value for approximately two minutes. If the tank pressure sensor value does change, pressurize the fuel tank side of the purge solenoid with the GE 41413-A / J 41413-A and the necessary adaptors. Now add smoke and allow pressure to stabilize for 2 minutes. If smoke is allowed to pass through the purge solenoid, replace the purge solenoid. If the tank pressure sensor value does not change, then install CH-48096 adaptor between the purge line from the canister and the purge solenoid. With the Evaporative Emissions System closed, pressurize the system through the CH-48096 adaptor and allow the system to completely stabilize, by observing the Press / Vac Gauge for a minimum of 5 minutes. Now add smoke to the system with GE 41413-A / J 41413-A after system stabilization. Now inspect the purge solenoid, engine side, fuel cap, canister vent solenoid filter and any line quick connects. When the leak is unable to be located, test under a vacuum condition. his type of leak may be detected by using the scan tool Purge/Seal function to create a vacuum in the Evaporative Emissions System and then observe the FTP sensor parameter for vacuum decay.
PIT5240B2017-08-15. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT:APPLIANCE:AIR CONDITIONER. This Preliminary Information communication provides information to the technician about systems operate during a remote vehicle start event. Dual Zone Auto Regular Production Option Code (CJ2) Heater-Vent-Air Conditioning settings the Heater-Vent-Air Conditioning settings will remain set to the previous Heater-Vent-Air Conditioning settings when the ignition was turned off. Single Zone Manual Regular Production Option Code (C67) HVAC settings the Heater-Vent-Air Conditioning settings will remain set to the previous Heater-Vent-Air Conditioning settings when the ignition was turned off. The Rear window defogger during a remote start event, the rear window defogger will turn on if the outside temperature is 44 degrees Fahrenheit (7 degrees Celsius) or below. The heated seats will not turn on if a Remote Vehicle Start event is performed within 2 hours of shutting the engine off. The cooled seats will turn to the high setting when the ambient temperature is above 80 degrees Fahrenheit (27 degrees Celsius). Heated steering wheel will not turn on during Remote Vehicle Start event.
PIT5233A2017-08-15. Service bulletin. STEERING; ELECTRICAL SYSTEM:IGNITION; ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician about vehicles that may have hard or unable to rotate ignition key concern. When the concern is present the steering wheel will need to be rotated in either direction to alleviate the pressure between the steering column lock pin and lock plate. Please communicate to the customer this condition is a normal operating characteristic of their vehicle.
PIP51792017-08-15. Service bulletin. EQUIPMENT:APPLIANCE:AIR CONDITIONER; ENGINE. This Preliminary Information communication provides information to the technician about vehicles that have extended or long crank time during cold ambient air temperatures. Direct Injection systems run at higher pressures, and the mechanical pump on the engine must build up the required pressure before the first injection event occurs. Direct Injection engines may have slightly longer cold crank times than that of port fuel engines.
PIP5174A2017-08-15. Service bulletin. ENGINE; FUEL SYSTEM, GASOLINE. This Preliminary Information communication provides information to the technician about vehicles that have an engine extended or long crank time during ambient air temps of ?18° Celsius (0° Fahrenheit) or colder when using E85 fuel. Technician will need to use Global Diagnostic System 2 to determine the actual ethanol content of the fuel. Adding regular fuel to the tank may help resolve the concern.
PIP5130C2017-08-15. Service bulletin. ENGINE; FUEL SYSTEM, GASOLINE; ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician how to diagnose and repair vehicles with an engine that runs with an intermittent crank no start with a Diagnostic Trouble Code P0011 or P00C6 current or history. Technician will need to use Global Diagnostic System 2 to actuate the cam phaser solenoid 4 or 5 times then try starting the vehicle. Then disable the ignition and fuel system. After the ignition and fuel system are disabled try to start the engine. Technician can now unplug the camshaft actuator to perform the following. Install a 20A fused jumper wire between the terminal 2 and 12V. Tickle/tap the low reference terminal 1 to ground on the cam actuator magnet, while cranking the engine over. When the engine starts and runs the cam actuator or oil control valve does not need to be replaced.
PIT5241B2017-08-15. Service bulletin. TRAILER HITCHES. This Preliminary Information communication provides information to the technician about customers that may request the factory Integrated Trailer Brake Controller Regular Production Option Code (JL1) be installed on their Full-Size Pickup or SUV when the vehicle was not ordered with the option. Dealer should advise the customer it cannot be added to the vehicle.
PIC5854B2017-08-15. Service bulletin. EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.. This Preliminary Information communication provides information to the technician about vehicles that may have a the AM or FM audio volume changes, mutes, echoes, cuts in and out, repeats broadcast content, or skips intermittently. Advise this is normal operation when listening to a weak AM or FM HD station. Technician can shut the HD option off to fix the concern.
PIT52682017-08-15. Service bulletin. EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.. This Preliminary Information communication advises the technician that some vehicles may have a radio display that is covered when the radio station favorites list is maximized. This is a normal operating characteristic and no repair attempt should be made. The hidden screen functions will operate again after the user minimizes the favorites list by dragging it to the bottom of the display.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.