WenmarOpen by Wenmar Pro

Service bulletins for the 2016 GMC Yukon XL

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

1454 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Only bulletins with component: Brakes are shown. Show all

Bulletins, newest first
PIT5377C2017-08-15. Service bulletin. SERVICE BRAKES, HYDRAULIC. This Preliminary Information communication provides information to the technician on the step needed to diagnose and repair vehicles that may have uneven brake pad wear. Technician will need to inspect and measure the brake pads thickness. Also determine the customer?s driving style. The disc brake pads should only be replaced if the friction surface is worn to within?2.0?mm (0.079?in) of the mounting plates. The rotors and pads should be replaced with the updated part number If the pads are out of specification, perform normal Service Information diagnostics to determine the cause of the concern.
PIT5202C2017-08-15. Service bulletin. ENGINE; POWER TRAIN; SERVICE BRAKES, HYDRAULIC:POWER ASSIST. This Preliminary Information communication provides information to the technician about vehicles that are equipped with 6L80 Regular Production Option Code (MYC), 6L90 Regular Production Option Code (MYD) or 8L90 Regular Production Option Code (M5U) Automatic Transmission. Starting with the 2013 model year, Full Size Trucks and Utilities now have Powertrain Grade Braking. Powertrain grade braking assists when driving on a downhill grade to help maintain desired vehicle speed by using the engine and transmission to slow the vehicle.
PIP5337G2017-08-15. Service bulletin. POWER TRAIN; VEHICLE SPEED CONTROL:LINKAGES; SERVICE BRAKES. This Preliminary Information communication provides information to the technician on the step to diagnose and repair the vehicles that may have a shake or shudder during light throttle acceleration, between 30 and 65 miles per hour steady state driving. Also shudder feeling that may be described as driving over rumble strips or rough pavement. Technician will need to run the vehicle in three different operational modes. The three modes are Normal, torque converter clutch open, and torque converter clutch closed. Technician will need to press and hold the tow-haul mode button for five seconds to disable grade braking to prevent downshifts during test. Technician will need to duplicate the concern in Normal mode. If the concern is gone in torque converter clutch open and closed then the torque converter should be replaced. If the concern is not present in normal mode, torque converter clutch open, and torque converter clutch closed the concern is not with the shudder. Technician should use of the PICO scope and Noise, Vibration and Harshness software can be used to confirm torque converter clutch shudder, Engine, Tire or Driveline component related conditions. Flush the cooler lines and cooler using DT-45096 transmission oil cooling system flush and flow test tool when the torque converter is replace.
PIT5206D2017-08-15. Service bulletin. ELECTRICAL SYSTEM; ENGINE; SERVICE BRAKES, HYDRAULIC:PEDALS AND LINKAGES. This Preliminary Information communication provides information to the technician with the steps on diagnosing and repairing vehicles that may have unwanted grade braking, reduced engine power with no Driver Information Center messages ? Brake Pedal Override Feature ?, transmission busy or frequent shifting up or down, and Diagnostic Trouble Codes P057B, P057C, and/or P057D may or may not be set. Technician will use this preliminary information to find the brake pedal position data parameters in the scan tool, and also to provide some additional diagnostic help. These issues may be caused by an incorrect brake pedal position sensor input to the engine control module. Technician will verify with the scan tool if the engine control module has the correct parameters for the brake pedal position sensor. If an engine control module brake pedal position sensor relearn is performed, the truck may be temporarily repaired until the intermittent wiring issue between the engine control module and brake pedal position sensor occurs again. On 2014 and newer trucks inspect and repair any damage to X115 and X119. On the 2014 and previous trucks inspect and repair any damage to X205.
PIT5206E2017-05-22. Service bulletin. SERVICE BRAKES, HYDRAULIC:PEDALS AND LINKAGES; PARKING BRAKE; ELECTRICAL SYSTEM: INTEGRATED TRAILER BRAKE CONTROL; POWER TRAIN:AUTOMATIC TRANSMISSION; ENGINE. THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN WITH THE STEPS ON DIAGNOSING AND REPAIRING VEHICLES THAT MAY HAVE UNWANTED GRADE BRAKING, REDUCED ENGINE POWER WITH NO DRIVER INFORMATION CENTER MESSAGES “ BRAKE PEDAL OVERRIDE FEATURE “, TRANSMISSION BUSY OR FREQUENT SHIFTING UP OR DOWN, AND DIAGNOSTIC TROUBLE CODES P057B, P057C, AND/OR P057D MAY OR MAY NOT BE SET. TECHNICIAN WILL USE THIS PRELIMINARY INFORMATION TO FIND THE BRAKE PEDAL POSITION DATA PARAMETERS IN THE SCAN TOOL, AND ALSO TO PROVIDE SOME ADDITIONAL DIAGNOSTIC HELP. THESE ISSUES MAY BE CAUSED BY AN INCORRECT BRAKE PEDAL POSITION SENSOR INPUT TO THE ENGINE CONTROL MODULE. TECHNICIAN WILL VERIFY WITH THE SCAN TOOL IF THE ENGINE CONTROL MODULE HAS THE CORRECT PARAMETERS FOR THE BRAKE PEDAL POSITION SENSOR. IF AN ENGINE CONTROL MODULE BRAKE PEDAL POSITION SENSOR RELEARN IS PERFORMED, THE TRUCK MAY BE TEMPORARILY REPAIRED UNTIL THE INTERMITTENT WIRING ISSUE BETWEEN THE ENGINE CONTROL MODULE AND BRAKE PEDAL POSITION SENSOR OCCURS AGAIN. ON 2014 AND NEWER TRUCKS INSPECT AND REPAIR ANY DAMAGE TO X115 AND X119. ON THE 2014 AND PREVIOUS TRUCKS INSPECT AND REPAIR ANY DAMAGE TO X205.
PIT5377D2017-03-23. Service bulletin. SERVICE BRAKES. THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ON THE STEP NEEDED TO DIAGNOSE AND REPAIR VEHICLES THAT MAY HAVE UNEVEN BRAKE PAD WEAR. TECHNICIAN WILL NEED TO INSPECT AND MEASURE THE BRAKE PADS THICKNESS. ALSO DETERMINE THE CUSTOMER’S DRIVING STYLE. THE DISC BRAKE PADS SHOULD ONLY BE REPLACED IF THE FRICTION SURFACE IS WORN TO WITHIN 2.0 MM (0.079 IN) OF THE MOUNTING PLATES. THE ROTORS AND PADS SHOULD BE REPLACED WITH THE UPDATED PART NUMBER IF THE PADS ARE OUT OF SPECIFICATION, PERFORM NORMAL SERVICE INFORMATION DIAGNOSTICS TO DETERMINE THE CAUSE OF THE CONCERN.
PIT5361A2017-03-23. Service bulletin. SERVICE BRAKES. THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR VEHICLES THAT MAY HAVE ISSUES WERE THE CUSTOMER WILL NEED INCREASED EFFORT TO DEPRESS THE BRAKE PEDAL. TECHNICIAN MAY FIND FLUID IN THE BRAKE BOOSTER AND/OR THE BOOSTER VACUUM LINE. TECHNICIAN WILL NEED TO REPLACE VACUUM PUMP, BRAKE BOOSTER, MASTER CYLINDER, VACUUM PUMP BELT AND THE VACUUM LINE BETWEEN THE BOOSTER AND THE PUMP.
PIT-5457-A2016-08-13. Service bulletin. SERVICE BRAKES, HYDRAULIC:ANTILOCK/TRACTION CONTROL/ELECTRONIC LIMITED SLIP:ABS WARNING LIGHT; SUSPENSION; STEERING:HYDRAULIC POWER ASSIST SYSTEM; SERVICE BRAKES, AIR:ANTILOCK:ABS WARNING LIGHT. THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS FOR DIAGNOSING THE CONCERN, AND COMPLETING A WIRING REPAIR. THE VEHICLE MAY HAVE A SERVICE ANTILOCK BRAKING SYSTEM, TRACTION CONTROL, POWER STEERING OR SUSPENSION SYSTEM MESSAGE ON THE DRIVERS INFORMATION CENTER.
PIT-5307-C2016-08-11. Service bulletin. ENGINE; SUSPENSION; EQUIPMENT:APPLIANCE:AIR CONDITIONER; SERVICE BRAKES, HYDRAULIC:ANTILOCK/TRACTION CONTROL/ELECTRONIC LIMITED SLIP:ABS WARNING LIGHT; SERVICE BRAKES, AIR:ANTILOCK:ABS WARNING LIGHT. THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE THE CONCERN WHEN THE VEHICLE HA SA SERVICE ENGINE SOON LIGHT, ANTILOCK BRAKING SYSTEM LIGHT OR SERVICE SUSPENSION MESSAGE, MISFIRE, HESITATION, NO CRANK, AIR CONDITIONING INOPERATIVE.
SB-08-24-152016-02-04. Service bulletin. POWER TRAIN:CLUTCH ASSEMBLY; SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:MASTER CYLINDER. GENERAL MOTORS: PARTS FOR MOST VEHICLES, CLUTCH, MASTER CYLINDER ASSEMBLY ARE, REQUIRED AND REQUESTED, TO BE RETURNED AND NEED TO REORDER REPLACEMENT PARTS USING SAME PART NUMBERS. *PE

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.