WenmarOpen by Wenmar Pro

Service bulletins for the 2014 GMC Sierra

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

3324 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Only bulletins with component: Electrical system are shown. Show all

Bulletins, newest first
PIC5839A2017-08-15. Service bulletin. ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician about vehicles that have a clock that is slow to update while driving. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle.
PIP51092017-08-15. Service bulletin. ELECTRICAL SYSTEM. This Preliminary Information communication advises the technician that E92 ECM part number 12656993 will be placed on a parts restriction through the General Motors Product Quality Center. Dealer will need to contact General Motors Product Quality Center for further assistance.
PIT4720C2017-08-15. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL. This Preliminary Information communication provides information to the technician that after replacing the Instrument Panel Cluster the exchange center is unable to program the actual mileage on the odometer or the actual mileage is unknown. Dealer will need to follow dealer to the General Motors service policies and procedures manual section 3.2.4 odometer servicing.
PIP51302017-08-15. Service bulletin. ELECTRICAL SYSTEM; ELECTRICAL SYSTEM:IGNITION. This Preliminary Information communication provides information to the technician how to diagnose and repair vehicles with an engine that runs with an intermittent crank no start with a Diagnostic Trouble Code P0011 or P00C6 current or history. Technician will need to use Global Diagnostic System 2 to actuate the cam phaser solenoid 4 or 5 times then try starting the vehicle. Then disable the ignition and fuel system. After the ignition and fuel system are disabled try to start the engine. Technician can now unplug the camshaft actuator to perform the following. Install a 20A fused jumper wire between the terminal 2 and 12V. Tickle/tap the low reference terminal 1 to ground on the cam actuator magnet, while cranking the engine over. This may have to be performed more than once.
PIT4551F2017-08-15. Service bulletin. ELECTRICAL SYSTEM:WIRING. This Preliminary Information communication provides information to the technician that during the Pre-Delivery Inspection it may be noticed that the backup alarm is inoperative. Technician can locate the wire harness on the right rear of the frame. Technician can route the harness up and over the spare tire hoist tube and connect to the backup alarm.
PIP50942017-08-15. Service bulletin. ELECTRICAL SYSTEM. This Preliminary Information communication advises the technician that, when testing any circuit for open or resistance, it is imperative that all related terminal pin fit and tension be checked when the test steps require disconnection of the connector or component, prior to any component replacement. Always use the recommended terminal test tool during these tests.
PI0360F2017-08-15. Service bulletin. ELECTRICAL SYSTEM. This preliminary informational bulletin provides information on GM Accessory Remote start not working with onstars remotelink phone applications
15-06-03-002B2017-08-15. Service bulletin. ELECTRICAL SYSTEM:12V/24V/48V BATTERY; EQUIPMENT. This informational bulletin provides information on Original Equipment Batteries Part Number and ACDelco Replacement Battery Approved Warranty Part Numbers
08-07-30-026C2017-08-15. Service bulletin. ELECTRICAL SYSTEM:STARTER ASSEMBLY. This informational bulletin provides information on vehicles may rock or move slightly forward or rearward while in Park at start up after cold soak and that this is considered a normal conditon and no repairs are necessary
16-NA-0692017-08-15. Service bulletin. ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL. This informational bulletin provides information on If the radar does not see any vehicles, structures, or objects for 15-25 minutes of driving, the system may think its blocked and display the ?Side Object Detection System Disabled? message.
11-08-49-001P2017-08-15. Service bulletin. ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL. This technical bulletin provides a procedure on how to take the vehicles out of transport mode for vehicles with the condition of Transport Mode On Message Displayed in Driver Information Center (DIC) and/or Battery Light is Flashing
06-00-89-029M2017-08-15. Service bulletin. ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL. This informational bulletin provides information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces, Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability
PIT3189R2017-08-15. Service bulletin. ELECTRICAL SYSTEM; LATCHES/LOCKS/LINKAGES:DOORS:LATCH; STRUCTURE:BODY:DOOR. This Preliminary Information communication provides information to the technician about customers that are unable to override the automatic door locking feature. Technician will update the Body Control Module on 2006 to 2007 model years. On 2010 to 2014 model years technician will need to contact Techline Customer Support for calibrations.
PIT4729E2017-08-15. Service bulletin. ELECTRICAL SYSTEM: INTEGRATED TRAILER BRAKE CONTROL; TRAILER HITCHES. This Preliminary Information communication provides information to the technician about customer's wanting to add the factory Integrated Trailer Brake Controller Regular Production Option Code (JL1) be installed on their Full Size pickup/utility when the vehicle was not ordered with the option. Dealer should advise the customer that if the vehicle does not have the option Regular Production Option Code (JL1) it cannot be added to the vehicle.
PIP51592017-08-15. Service bulletin. ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on. Technician may find Diagnostic Trouble Codes P0300 to P0308. Technician will need to inspect the spark plug wires and replace if needed.
PIC58622017-08-15. Service bulletin. EXTERIOR LIGHTING; ELECTRICAL SYSTEM; EXTERIOR LIGHTING:BRAKE LIGHTS. This Preliminary Information communication provides information to the technician about vehicles that have brake lights remain on with the vehicle off and parked and/or the vehicle battery goes dead. Technician will need to inspect for aftermarket parts.
PIT4816E2017-08-15. Service bulletin. ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician about vehicles that have multiple electrical concerns and or intermittent no crank. Technician will need to remove the 175 amp Mega Fuse and inspect for arcing. If any type of arcing is found replace the affected components. Technician will also check the voltage drop on the positive and negative and the torque of the cable at the starter.
PIT5234A2017-08-15. Service bulletin. ELECTRICAL SYSTEM:IGNITION; ELECTRICAL SYSTEM:IGNITION:SWITCH. This Preliminary Information communication provides information to the technician about vehicles that have an ignition key cannot be turned. Technician will need to insert the key and measure the gap from the key to the cylinder. If the key is not going in fully the ignition lock cylinder will need to be replaced. Also obtain a new key that is cut to the vehicle. Technician will need to shorten the key shank by grinding or cutting 6-7 millimeter (1/4 inch) off the tip of the key, and then bevel the tip of the key. Now the technician can install the new ignition lock cylinder.
PIC5492B2017-08-15. Service bulletin. ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D-37 history in the Vehicle Communication Interface Module or telematics communication interface control module. Engineering has determined that this code will only display in history on the scan tool and will not cause issues with OnStar system operation.
PIT52362017-08-15. Service bulletin. ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Technician will need to call General Motors Technical Assistance Center for further assistance. If the Diagnostic Trouble Code B101D has a sym 37 set please refer to the latest version of PIC5492.
PIT4844E2017-08-15. Service bulletin. ELECTRICAL SYSTEM; STEERING; VEHICLE SPEED CONTROL:CRUISE CONTROL. This Preliminary Information communication provides information to the technician with the installation of Cruise Control on a vehicle which did not come equipped with the option. Technician will need to contact the Techline Customer Support Center to determine if a calibration is available for the vehicle. If they are able to provide a calibration for the vehicle then order steering wheel with cruise control buttons, steering wheel sir coil, and steering column wiring harness.
PIT5184A2017-08-15. Service bulletin. STEERING: STEERING WHEEL/HANDLE BAR; ELECTRICAL SYSTEM:WIRING; ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician about vehicles that have an instrument panel backlighting flashes, flickers or inoperative, unwanted horn activation, radio controls inoperative or unwanted activation, OnStar unwanted activation, and cruise control inoperative. Technician should inspect for a short to ground on the steering wheel near the Supplemental Inflatable Restraint coil connector X2 and make necessary repairs to any shorted circuits and then position the wiring.
PIP5130A2017-08-15. Service bulletin. ELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING. This Preliminary Information communication provides information to the technician how to diagnose and repair vehicles with an engine that runs with an intermittent crank no start with a Diagnostic Trouble Code P0011 or P00C6 current or history. Technician will need to use Global Diagnostic System 2 to actuate the cam phaser solenoid 4 or 5 times then try starting the vehicle. Then disable the ignition and fuel system. After the ignition and fuel system are disabled try to start the engine. Technician can now unplug the camshaft actuator to perform the following. Install a 20A fused jumper wire between the terminal 2 and 12V. Tickle/tap the low reference terminal 1 to ground on the cam actuator magnet, while cranking the engine over. This may have to be performed more than once.
PIT5206A2017-08-15. Service bulletin. SERVICE BRAKES, AIR:CONTROLS:FOOT CONTROL/VALVE; ELECTRICAL SYSTEM:SOFTWARE; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). This Preliminary Information communication provides information to the technician with the steps on diagnosing and repairing vehicles that may have unwanted grade braking, reduced engine power with no Driver Information Center messages " Brake Pedal Override Feature ", transmission busy or frequent shifting up or down. Technician will use this preliminary information to find the brake pedal position data parameters in the scan tool, and also to provide some additional diagnostic help. These issues may be caused by an incorrect brake pedal position sensor input to the engine control module. Technician will verify with the scan tool if the engine control module has the correct parameters for the brake pedal position sensor.
PIT5181A2017-08-15. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL. This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on. Technician may find DTCs P057C and or P057D. Some vehicles may have cruise and brake light operation service stability message with Diagnostic Trouble Codes C0161 and C0277. Technician will need to inspect connector X205 for loose, backed out, or bent terminals using the appropriate terminal test probe.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.