Service bulletins for the 2009 GMC Savana
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
1187 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
By topic
| PIT5319 | 2017-08-15. Service bulletin. EQUIPMENT:ELECTRICAL. This Preliminary Information communication provides information to the technician about vehicles that the OnStar LED is staying on after the vehicle Retained Accessory Power has turned off and/or their Bluetooth phone stays connected after leaving the vehicle. Technician will need to perform a power cycle to the Vehicle Communication Interface Module. If the concern is gone, no further action is required. If the concern is still present after the power cycle technician will need to contact General Motors Technical Assistance Center for further assistance. |
|---|---|
| PIP4932C | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING. This Preliminary Information communication provides information to the technician about vehicles with Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0101. Technician should follow published Service Information diagnostics for any Diagnostic Trouble Codes that are set. If during diagnosis the tech has found that the Airflow Leak Equivalency Ratio or Induction System Leak Indication is above or below the specification the tech will have to carefully check for leaks in the air intake. |
| PIT3099M | 2017-08-15. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY. This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Technician can also contact Partect for assistance. Technician can also contact Techline Customer Support Center for programming issues. |
| PIC5759A | 2017-08-15. Service bulletin. EQUIPMENT:ELECTRICAL; EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.. This Preliminary Information communication provides information to the technician about vehicles that have a message on the radio "maximum number of phones are currently paired to the vehicle". Dealer should advise the customer this is normal operation of the vehicle due to the maximum number of five phones can be paired to a vehicle. |
| PIC4310J | 2017-08-15. Service bulletin. EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM); EQUIPMENT:ELECTRICAL. This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system. |
| PIP5163A | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING. This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure. |
| PIT5289 | 2017-08-15. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT:ELECTRICAL. This Preliminary Information communication provides information to the technician about vehicles that may have "Service Charging System" message displayed on the DIC and/or a low voltage reading on the volt gauge during the first several minutes after a cold start. Technician may find B1517 sym 03 may be set. Technician will update the Body Control Module with the latest calibrations. |
| PIT4813E | 2017-08-15. Service bulletin. ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician about vehicles with a "Service Charging System" message displayed on the Driver Information Center and/or a low voltage reading on the volt gauge during the first several minutes after a cold start. Technician may find a Diagnostic Trouble Code B15517 sym 03. If this concern only occurs during the first several minutes of a cold start, no repairs should be made. Dealer should communicate to the customer that this is normal operating characteristic of vehicles equipped with the diesel engine. |
| PIP3119M | 2017-08-15. Service bulletin. ENGINE; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR. This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have a Service Engine Soon Malfunction Indicator Lamp on at low mileage. Technician may find Diagnostic Trouble Codes P0420 and or P0430 stored. Technician should be advised that the catalytic converter efficiency Diagnostic Trouble Codes P0420 and P0430 are disabled for the first hour of engine run time to allow break-in of the catalytic converter. Technician will need to use a Tech2 to check the verify engine run time on the Engine Hour Meter in the Instrument Panel Cluster Data Display/Data 1 List in the scan tool match. If the engine run time is less than one hour, the battery may have been disconnected, or another vehicle power loss event may have occurred, during vehicle manufacturing. Technician will need to clear the Diagnostic Trouble Codes and perform a drive cycle. If the catalytic converter was replaced and the Diagnostic Trouble Codes set it may be a result of the engine run time restrictions no longer being in place since the vehicle is no longer new. Technician will need to clear the Diagnostic Trouble Codes and perform a drive cycle. |
| PIP4792D | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING; FUEL SYSTEM, GASOLINE. This Preliminary Information communication provides information to the technician about vehicles that have a an extended crank on cold start, brief rough running on cold start, black exhaust color, and/or Service Engine Soon Malfunction Indicator Lamp on. Technician may find a Diagnostic Trouble Code P0172 and or P0175. Technician will need to check the Fuel Alcohol Content parameter found in the Fuel Trim Data List of the scan tool and the measured ethanol content of a fuel sample using the J44175 tester. If the difference is 17% or greater, reprogram the Engine Control Module with the latest calibrations from TIS2web. |
| PIP5168A | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING. This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have a no crank concern. Technician will need to check the valve train for movement when the engine is cranked. If the valve train is not moving while the crankshaft is moving the front cover will need to be removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly. If the valve train is rotating during inspection, disconnect the Camshaft Position sensor and check if the engine will start. If the engine starts front cover will need to be removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly. If the engine does not start with the Camshaft Position sensor disconnected the follow published "Engine Cranks But Does Not Run" diagnosis in Service Information. Also perform an Engine Compression Test and Cylinder Leakage Test in Service Information documents all results. If the Service Information procedures above isolate an engine mechanical concern then removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly. |
| PIC5953 | 2017-08-15. Service bulletin. EQUIPMENT:ELECTRICAL. This Preliminary Information communication provides information to the technician about vehicles that may have an issue when using Bluetooth voice recognition with an iPhone. Technician should work with the customer to insure the phone contacts to not have any Emojis loaded to any contact. |
| PIP3140F | 2017-08-15. Service bulletin. EQUIPMENT. This Preliminary Information communication advises the technician that a noise or a vibration in the vehicle that seems to be abnormal may not have been there when the vehicle was purchased. Technician should look for Non - General Motors aftermarket accessories installed on the vehicle that can cause these issues. |
| PIT4813D | 2017-08-15. Service bulletin. ELECTRICAL SYSTEM; ENGINE. This Preliminary Information communication provides information to the technician about vehicles with a "Service Charging System" message displayed on the Driver Information Center and/or a low voltage reading on the volt gauge during the first several minutes after a cold start. Technician may find a Diagnostic Trouble Code B15517 sym 03. If this concern only occurs during the first several minutes of a cold start, no repairs should be made. Dealer should communicate to the customer that this is normal operating characteristic of vehicles equipped with the diesel engine. |
| PIT4423H | 2017-08-15. Service bulletin. ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician about vehicles that have an aftermarket, add-on back up alarm will sound when unlocking the doors with the Remote Keyless Entry remote. Technician can correct this concern by turning off the perimeter lighting feature on vehicles with Driver Information Center controls or install an isolation relay in-line to the backup alarm. |
| PIP5169 | 2017-08-15. Service bulletin. ENGINE. This Preliminary Information communication provides information to the technician about vehicles that are setting Diagnostic Trouble Code P0300 after engine repairs. Technician will need to ensure that injector connectors for cylinder 5-7 and 6-8 are not crossed. |
| PIP5168 | 2017-08-15. Service bulletin. ENGINE. This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have a no crank concern. Technician will need to check the valve train for movement when the engine is cranked. If the valve train is not moving while the crankshaft is moving the front cover will need to be removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly. If the valve train is rotating during inspection, disconnect the Camshaft Position sensor and check if the engine will start. If the engine starts front cover will need to be removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly. If the engine does not start with the Camshaft Position sensor disconnected the follow published ?Engine Cranks But Does Not Run? diagnosis in Service Information. Also perform an Engine Compression Test and Cylinder Leakage Test in Service Information documents all results. If the Service Information procedures above isolate an engine mechanical concern then removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly. |
| PIC5491E | 2017-08-15. Service bulletin. ELECTRICAL SYSTEM; ELECTRICAL SYSTEM:SOFTWARE. This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. After the vehicle has powered down, remove power to the OnStar module for five minutes. After the power has been removed for five minutes, if the OnStar system is working release the vehicle. If the OnStar system is still inoperative continue with published Service Information diagnostics. Technician may need to contact General Motors Technical Assistance Center depending on the STID, Station ID, or OnStar Customer Identifier. |
| PIC3011H | 2017-08-15. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. This Preliminary Information communication provides information to the technician about vehicles that have the OnStar system does not respond properly to some numbers and/or voice commands. Dealer should direct the customer to review the operational characteristics in the OnStar Users Guide. |
| PIP5168B | 2017-08-15. Service bulletin. ENGINE. This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have a no crank concern. Technician will need to check the valve train for movement when the engine is cranked. If the valve train is not moving while the crankshaft is moving the front cover will need to be removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly. If the valve train is rotating during inspection, disconnect the Camshaft Position sensor and check if the engine will start. If the engine starts front cover will need to be removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly. If the engine does not start with the Camshaft Position sensor disconnected the follow published ?Engine Cranks But Does Not Run? diagnosis in Service Information. Also perform an Engine Compression Test and Cylinder Leakage Test in Service Information documents all results. If the Service Information procedures above isolate an engine mechanical concern then removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly. |
| PIT4943C | 2017-08-15. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL; FUEL SYSTEM, GASOLINE; SERVICE BRAKES, HYDRAULIC. This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0442. Technician will need to review Techlink article from May 2013 titled "Using the Evaporative Emissions System Tester" Technician will need to follow these steps to help diagnose the issue. First after the P0442 has been verified do not disturb any of the fuel system components. The technician now can use the scan tool to close the Evaporative Emissions System. If possible change the tank pressure sensor units from inch_H2O to milimeter_Hg for better resolution. Now the vehicle can be stared to monitor the tank pressure sensor output value for approximately two minutes. If the tank pressure sensor value does change, pressurize the fuel tank side of the purge solenoid with the GE 41413-A / J 41413-A and the necessary adaptors. Now add smoke and allow pressure to stabilize for 2 minutes. If smoke is allowed to pass through the purge solenoid, replace the purge solenoid. If the tank pressure sensor value does not change, then install CH-48096 adaptor between the purge line from the canister and the purge solenoid. With the Evaporative Emissions System closed, pressurize the system through the CH-48096 adaptor and allow the system to completely stabilize, by observing the Press / Vac Gauge for a minimum of 5 minutes. Now add smoke to the system with GE 41413-A / J 41413-A after system stabilization. Now inspect the purge solenoid, engine side, fuel cap, canister vent solenoid filter and any line quick connects. When the leak is unable to be located, test under a vacuum condition. his type of leak may be detected by using the scan tool Purge/Seal function to create a vacuum in the Evaporative Emissions System and then observe the FTP sensor parameter for vacuum decay. |
| PIC5453A | 2017-08-15. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. This Preliminary Information communication provides information to the technician that General Motors and General Motors of Canada Company do not support cross border sales. The General Motors of Canada Customer Care Centre is the sole authorized provider of a certification confirmation letter which helps our customers identify if their vehicles meets the required USA regulatory standards necessary for importation into the USA. |
| PIP5104A | 2017-08-15. Service bulletin. ENGINE. This Preliminary Information communication provides information to the technician about vehicles that may have a cold engine tick noise for 50 seconds at start up. Technician determines if the tick noise is possibly coming from the exhaust manifold, as this noise could easily be mistaken for an engine tick noise. If your SI diagnosis does not isolate the cause of this concern, this concern should be considered a vehicle design characteristic of the ECM calibration and no additional repairs should be performed. |
| PIT5125A | 2017-08-15. Service bulletin. EXTERIOR LIGHTING:HEADLIGHTS:SWITCH; ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician about vehicles proper operation of the stop and/or turn signals. For vehicles without Regular Production Option Code V4D circuit 618 is for the left stop and turn signal and circuit 619 dark green is for the right stop and turn signal. For vehicles with Regular Production Option Code V4D circuit 618 yellow is for the left turn signal only. Circuit 619 dark green is for the right turn signal only and circuit 1320 light blue is for the stop lamps only. |
| PIP3343D | 2017-08-15. Service bulletin. ENGINE. This Preliminary Information communication provides information to the technician about vehicles that have an oil leak shortly after a cold start when extremely low ambient temperatures are present. Technician will need to clean the area of the oil leak, clean and dry the PCV hoses, and replace the oil fill cap with part number 12589430. |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.