Service bulletins for the 2021 Freightliner 114SD
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
153 on file from NHTSA, as of 2026-10-19.
By type
By component
| SB54-308 | 2021-02-26. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:ENGINE CONTROL MODULE (ECU/ECM):SOFTWARE; EQUIPMENT. Freightliner Service Bulletin for Programming Chassis Electronic Control Units (ECUs) With DiagnosticLink. |
|---|---|
| ICI21-003 | 2021-02-26. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. Superseding Letter to an Important Campaign Information Letter to announce a reimbursement available to dealers for travel to a customer's location to perform a recall or field service campaign. Potential travel reimbursement applies to DTNA truck dealers and Detroit Diesel distributors. Thomas Built Buses will be addressed separately. This letter supersedes ICI20-022R. |
| WI21-006 | 2021-02-26. Service bulletin. ELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING; EQUIPMENT ADAPTIVE/MOBILITY; EQUIPMENT. Warranty Information Letter for Detroit NOx Sensor Circuit Fault Codes - Claim Guidelines. |
| WI20-014R | 2021-02-25. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. Revised Warranty Information Letter for OWL and Warranty Manual Improvement: Sublets and Travel Time/Distance. In the spirit of continuous improvement, DTNA reviewed sublet-related policies and procedures. The goal was to improve language clarity and optimize processes. Revisions are in blue font. |
| TechTalk8023 | 2021-02-02. Service bulletin. ENGINE AND ENGINE COOLING; ELECTRICAL SYSTEM. Tech Talk discussion on Cummins FC 383 Intake Heater. |
| SB35-036 | 2020-12-30. Service bulletin. POWER TRAIN. Revised Freightliner Service Bulletin for Axle Flange Gasket Replaced with O-Ring. Revision removed steps instructing removal and installation of wheels. Daimler Trucks North America has released a new axle shaft to hub rubber O-ring (part number 11-30728-000) as a replacement for the paper gasket (part number 11-14418-000). The new O-ring will provide better sealing and is reusable. It is quicker and easier to use compared to the paper gasket, because using a paper gasket requires cleaning the hub when the axle shaft is removed. |
| SB42-079 | 2020-12-30. Service bulletin. SERVICE BRAKES. Freightliner Service Bulletin for Access to Front Brake Zerk Fittings. Certain vehicles with Detroit front axles and Meritor EX-L front air disc brakes do not have access to the front brake zerk fittings for lubrication. |
| WP20-018R | 2020-12-12. Service bulletin. STEERING; POWER TRAIN. Revised Warranty Policy Letter for Alliance/Mascot Aftermarket Warranty and Claim Filing. Revisions are in blue. With Mascot now in partnership with Detroit Reman and Alliance Parts, DTNA is pleased to announce that Mascot coverage has been added to OWL. Remanufactured Alliance/Mascot parts include transmission, differential, steering gear, and steering pump used in an on-highway vehicle applications. The Alliance/Mascot aftermarket warranty coverage period has not changed: depending on the part, coverage is for one (1) or two (2) years and current parts, labor, and reimbursement policies apply. |
| WP20-018 | 2020-12-12. Service bulletin. STEERING; EQUIPMENT ADAPTIVE/MOBILITY; EQUIPMENT; POWER TRAIN. Warranty Policy Letter for Alliance/Mascot Aftermarket Warranty and Claim Filing. With Mascot now in partnership with Detroit Reman and Alliance Parts, DTNA is pleased to announce that Mascot coverage has been added to OWL. Remanufactured Alliance/Mascot parts include transmission, differential, steering gear, and steering pump used in an on-highway vehicle applications. The Alliance/Mascot aftermarket warranty coverage period has not changed: depending on the part, coverage is for one (1) or two (2) years and current parts, labor, and reimbursement policies apply. |
| CALFTL54-013 | 2020-12-08. Service bulletin. ELECTRICAL SYSTEM. Customer Advisory Letter for Updating the RP170 Customer Access Connector and Adding Overlays for J1939. The Electrical Guide for M2106, M2112, 108SD, 114SD Body Builder Reference Guide Revision: D June 2019 incorrectly displays pins 2 and 3 of the customer access 8 pin connector on table 5 as Hot with crank, Ignition controlled battery (+) thru Disconnect switch (If disconnect switch specified). |
| 20TS-08 | 2020-12-07. Service bulletin. ENGINE AND ENGINE COOLING. Technical Service Letter for Fault Code SPN 2629 FMI 10 on GHG21 936.917 DD8 Dual Stage Turbo with MCM Software Version 14 |
| SS1034797 | 2020-11-02. Service bulletin. EQUIPMENT; ENGINE AND ENGINE COOLING; ELECTRICAL SYSTEM. Service Solution for M2,108SD, 114SD Coolant Level Sensor P/N 06-93316-002. The Call Center has received several calls pertaining to this LCL sensor introduced to in 2018. The purpose of this solution is to bring better awareness to the sensor functions, fault codes generated, along with providing testing procedures used to validate the sensors condition. |
| SB54-278 | 2020-10-28. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM. Updated Freightliner Service Bulletin for Powernet Troubleshooting Guide - Batteries, Path, Alternator, and Starter. This bulletin replaces the version dated 5/31/2017. Information is added about the BCT-460DTNA PowerNet Assessment Tool. When troubleshooting Powernet issues, use the BCT-460DTNA PowerNet Assessment Tool. As of May 29, 2018, the AutoMeter® is the only Daimler-approved tool for troubleshooting vehicle Powernet issues. |
| 20TS-07 | 2020-10-21. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); ENGINE AND ENGINE COOLING. Technical Service Letter for Cold Weather Faults on GHG17/21 DD13 with MCM Software Version 14. Due to colder weather, there may be an increase in the frequency of faults, noted below, on GHG17/21 DD13 trucks built after June 5th 2019. This is due to a calibration issue in the current MCM software (14.1.1.5 or 14.2.1.3). New software is scheduled for release in the first quarter of 2021 that will address these faults. |
| 17TS-05REV2 | 2020-10-21. Service bulletin. POWER TRAIN; ELECTRICAL SYSTEM:SOFTWARE. Revised Technical Service Letter for Detroit DT12 TCM GHG17 Only; Bootloader Update. On Detroit DT12 equipped vehicles, it may be necessary to complete an additional step in the programming process when updating the TCM software. |
| 20TS-06 | 2020-10-13. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; ENGINE AND ENGINE COOLING. DDC Technical Service Letter for GHG17 DD Platform Heavy Duty Oil Pan Drain Plug Inserts. Some GHG17 DD Platform Heavy Duty oil pans may experience an issue with the oil pan drain plug insert spinning during removal or installation while completing an oil change. Leaking may also be observed at the drain plug and/or other plugs in the oil pan. |
| SB35-036 | 2020-10-12. Service bulletin. EQUIPMENT; POWER TRAIN. Freightliner Service Bulletin for Axle Flange Gasket Replaced with O-Ring. Daimler Trucks North America has released a new axle shaft to hub rubber O-ring (part number 11-30728-000) as a replacement for the paper gasket (part number 11-14418-000). The new O-ring will provide better sealing and is reusable. It is quicker and easier to use compared to the paper gasket, because using a paper gasket requires cleaning the hub when the axle shaft is removed. |
| 18SP736 | 2020-10-01. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:BELTS AND ASSOCIATED PULLEYS; ENGINE AND ENGINE COOLING:COOLING SYSTEM:FAN. Detroit Diesel Special Publication informing about Heavy Duty Friction Style Belt Tensioner Kit. This heavy duty friction style belt tensioner kit contains the belt tensioner and two M10 bolts to correctly pin the friction style belt tensioner. The M10x80mm bolt is used to pin the engine cooling fan drive arm. The M10x50mm bolt is used to pin the engine accessory drive arm. |
| 20TS-03REV2 | 2020-10-01. Service bulletin. ENGINE AND ENGINE COOLING. Revised Technical Service Letter for DD Heavy Duty Platform Belt Tensioner Change. A newly designed, dual-arm friction shoe damping tensioner was implemented for the DD Heavy Duty Platform. The revision includes additional information on retrofit and service kits. |
| TechTalk7679 | 2020-10-01. Service bulletin. ENGINE AND ENGINE COOLING. Tech Talk discussion on repair verification for codes like 'low air flow' when a trailer is not available. |
| TechTalk4725 | 2020-09-30. Service bulletin. STEERING; EQUIPMENT. Tech Talk discussion about power steering fluid. |
| 20CSA-15 | 2020-09-02. Service bulletin. ELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING; EQUIPMENT. Customer Service Announcement for Release of DiagnosticLink 8.12 Service Pack 2. On Thursday, September 3, 2020, Service Pack (SP) 2 for DiagnosticLink 8.12 Standard and Professional will be made available to download from the Detroit Diesel server. |
| ICI20-026 | 2020-09-01. Service bulletin. ENGINE AND ENGINE COOLING; EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. Important Campaign Information Letter informing that revised bulletins for Detroit Diesel campaigns D20R1REV1 and D20M8REV1 have been posted on DTNAConnect. |
| D20R1REV1 | 2020-09-01. Service bulletin. ENGINE AND ENGINE COOLING; ELECTRICAL SYSTEM:SOFTWARE. Revised Detroit Emissions Recall for Daimler Trucks North America LLC, on behalf of its Detroit Powertrain Division, has determined that some Model Year 2020 GHG21 DD13 engines require reprogramming of the MCM to meet certification. NOTE: Reference 20TS-04 Detroit CPC501T GHG21 Only; Bootloader Update if New Cascadia CPC501T is not at the software level shown in this table. The Corrective Procedure also has been updated. |
| D20R1 | 2020-09-01. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. Detroit Emissions Recall for GHG21 Detroit DD13 Model Year 2020 Software Reprogramming. Daimler Trucks North America LLC, on behalf of its Detroit Powertrain Division, has determined that some Model Year 2020 GHG21 DD13 engines require reprogramming of the MCM to meet certification. |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.