WenmarOpen by Wenmar Pro

Service bulletins for the 2018 Ford Transit

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

192 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

Only bulletins with component: Electrical system are shown. Show all

Bulletins, newest first
SSM 484302020-02-04. Service bulletin. ELECTRICAL SYSTEM. Some 2018-2020 Escape/Corsair, Edge, Explorer, Fusion, Transit Connect Vehicles equipped with a TCU may exhibit a "Battery Backup Component Failure" message in the cluster. This may be accompanied by DTC 1477-09 - Backup Battery Component Failure. This may be due to the TCU experiencing a sudden temperature change. To correct this condition, reprogram the TCU using the appropriate Ford diagnostic scan tool. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 483402019-12-05. Service bulletin. ELECTRICAL SYSTEM. Some 2016-2019 vehicles equipped with SYNC 3 may experience a map displayed on the left half of the SYNC screen with no other information/soft buttons present after updating to the latest version of V3.0 software. This issue occurs when the SYNC 3 system has been previously modified using an aftermarket device to display the Ford GT welcome screen/HMI Theme. To correct this issue, please contact the Technical Hotline Assistance Center to have the vehicle restored back to its original state.
SSM 480532019-07-08. Service bulletin. ELECTRICAL SYSTEM. Some 2016-2019 Ford and Lincoln vehicles equipped with SYNC 3 not at the latest software level may exhibit Various Performance Related concerns such as Display Operation, Navigation, Voice Recognition, Phone Pairing, Applink, Travel Link, Slow System Response, etc. Check for SYNC software update under the OASIS Tab SYNC selection. If an update is available refer to WSM,Section 415-00 and update the APIM software. After Installation, complete pop-up appears, remove USB flash drive and install into IDS tool to update Ford database. Perform a complete ignition cycle by turning the key off for 5 minutes which is critical for a successful installation. If no updates are available or a blue or black screen is present after an update refer to WSM, Section 415-00 for diagnosis or SYNC 3 intermittent blank screen GSB for tips. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual. Section
SSM 480182019-07-08. Service bulletin. ELECTRICAL SYSTEM; VISIBILITY:POWER WINDOW DEVICES AND CONTROLS. Some 2015-2019 Transit vehicles may exhibit inoperative power door locks and/or power windows due to water intrusion in the door to body harness connector C339 (left) or C340 (right). If corrosion is found, service pigtails JU2Z-14S411-RA (gray) and JU2Z-14S411-PA (black) are released to service the body harness (female) side of the connector, without replacing the entire 14401 body harness. Service the pigtail(s) and replace the door harness as needed, while making sure the door to body accordion grommet ends and surrounding body plugs are properly seated to prevent future water intrusion. For claiming use causal part 14631 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 479262019-05-07. Service bulletin. FUEL SYSTEM, GASOLINE; ELECTRICAL SYSTEM. SSM 47926 - 2018-2019 F-150/Expedition/Navigator/Transit/Explorer - Illuminated MalfunctionIndicator Lamp (MIL) With Diagnostic Trouble Code (DTC) P025A Some 2018-2019 F-150, Expedition, Navigator, Transit and Explorer vehicles may exhibit an illuminated MIL with DTC P025A stored in the powertrain control module (PCM). This may be due to an intermittent or partial disconnect of the harnessto the fuel pump driver module (FPDM) connector. Confirm FPDM connector (F-150 C4336, Expedition/Navigator C433, Transit C433, Explorer C3239) is fully seated prior to performing PC/ED diagnostics or replacing any components. APPLICABLE VEHICLES
SSM 478502019-05-07. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT:APPLIANCE:AIR CONDITIONER. Some 2013-2019 vehicles equipped with a EVDC air conditioning (A/C) compressor may exhibit poor A/C performance/improper climate function and/or a diagnostic trouble code (DTC) P06A0 in the powertrain control module (PCM). To support the proper diagnosis of this compressor, the EVDC control valve tester has been developed and is available from Rotunda (339-EVDC100). A tester has been provided to each U.S. dealership free of charge with shipments completed 19-Apr-2019 (reference EFC07013 on FMCDealer.com). This tester will help reduce the potential for misdiagnosis and unnecessary compressor replacement. Make sure that this tester is used for warranty repairs and document the test results in the Technician Comments field. Refer to the Rotunda catalog for a video and user manual which provide detailed operating instructions.
SSM 478242019-04-08. Service bulletin. ELECTRICAL SYSTEM. Some 2015-2017 vehicles may experience a no crank concern due to a security access key table error. When attempting to program keys or perform a parameter reset, the procedure may fail and the Integrated Diagnostic System (IDS) scan tool may display an error 232: Key Table Not Allocated. If this error message is encountered, the Body Control Module (BCM) is internally faulted and requires replacement. For claiming, use causal part 15604 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.
TSB 19-20352019-04-08. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; FUEL SYSTEM, GASOLINE; ELECTRICAL SYSTEM. Some 2016-2019 Transit vehicles equipped with a 3.2L diesel engine built on or before 7-Feb-2019 may exhibit an illuminated malfunction indicator lamp (MIL) with only diagnostic trouble code (DTC) P054E stored in the powertrain control module (PCM). This may be due to the PCM software. Update the PCM software to resolve the condition.
TSB 19-20162019-04-08. Service bulletin. ELECTRICAL SYSTEM; FUEL SYSTEM, GASOLINE; ENGINE. Some 2016-2018 Transit vehicles equipped with a 3.2L Duratorq diesel engine and built on or before 13-Feb-2018 may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P24A0 and/or P26A0 in the powertrain control module (PCM). Follow the Service Procedure steps to correct the condition.
SSM 478242019-04-01. Service bulletin. ELECTRICAL SYSTEM. Some 2015-2017 vehicles may experience a no crank concern due to a security access key table error. When attempting to program keys or perform a parameter reset, the procedure may fail and the Integrated Diagnostic System (IDS) scan tool may display an error 232: Key Table Not Allocated. If this error message is encountered, the Body Control Module (BCM) is internally faulted and requires replacement. For claiming, use causal part 15604 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.
TSB 19-20162019-04-01. Service bulletin. FUEL SYSTEM, GASOLINE; FUEL SYSTEM, DIESEL; ELECTRICAL SYSTEM. Some 2016-2018 Transit vehicles equipped with a 3.2L Duratorq diesel engine and built on or before 13-Feb-2018 may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P24A0 and/or P26A0 in the powertrain control module (PCM). Follow the Service Procedure steps to correct the condition.
SSM 477222019-03-04. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. Some 2018-2019 Escape, Transit Connect and EcoSport vehicles equipped with a keyed ignition and a factory invoiced accessory (FIA) VSS may exhibit intermittent alarm activation with lights flashing and the horn sounding after a loud noise and/or shockwave near the vehicle (ex. large truck passing, garage door slamming closed). The root cause of this concern may be an incorrect shock sensor sensitivity adjustment on the VSS module. Perform the shock sensor sensitivity adjustment procedure outlined in the vehicle security/remote start installation guide located on the PTS website. The shock sensor requires adjustment during the installation of a vehicle security/remote start system. The shock sensor sensitivity adjustment procedure should be performed following the installation instructions.
SSM 477112019-03-04. Service bulletin. ELECTRICAL SYSTEM. Some 2016-2019 Ford and Lincoln vehicles equipped with SYNC 3 and a 6, 8 or 10 inch screen may show a pop-up message every key cycle that states 'SYNC can check for updates when connected to a WiFi network'. To remove the inconvenience of the pop-up the customer can either connect to a trusted WiFi network to complete the setup process or turn off WiFi in the WiFi settings located under the Settings menu. Adjusting the setting for the customer is not a warrantable defect.
SSM 476732019-01-07. Service bulletin. ELECTRICAL SYSTEM. Some 2016-2019 Transit vehicles equipped with a 3.2L diesel may indicate a blank PCM when connected to the Ford diagnostic scan tool. Do not replace the PCM. As a work around to access the PCM, remove the key from the ignition for 1 minute. Then remove the PCM relay in the battery junction box. Reinstall the PCM power relay, then put the key in the ignition and turn to on and attempt to access the PCM. Engineering is investigating the issue. Monitor OASIS for updates.
SSM 476712019-01-07. Service bulletin. ELECTRICAL SYSTEM. For 2015-2019 Transit vehicles, multiple fuse assemblies for the high current battery junction box are available for service. Do not replace the high current battery junction box assembly/wire harness to service an open fuse. Use part number BK2Z-14526-A for the 40 amp/100 amp/470 amp assembly, BK2Z-14526-B for the 2x60 amp/2x80 amp/3x100 amp/200 amp assembly, and BK2Z-14S411-A for the 60 amp MIDIù fuses on the outboard side of the driver seat base. Refer to Wiring Diagram Cell 11-7 for proper location.
SSM 476352019-01-07. Service bulletin. ELECTRICAL SYSTEM. When connecting the Vehicle Communication Module (VCM) and Integrated Diagnostic System (IDS) or Ford Diagnosis and Repair System (FDRS) to the DLC located on the driver side under the steering column at the GWM, make sure that the ignition is off before connecting the VCM. If the ignition is on or the engine is running during the connection, it can result in various warning lights being illuminated with diagnostic trouble codes (DTCs), no start, no crank conditions or the IPC inoperative. If a vehicle displays these issues, disconnect the equipment from the DLC and disconnect the vehicle battery. Wait 10 minutes and reinstall with the ignition off. Clear any DTCs present and retest.
SSM 475382018-12-03. Service bulletin. ELECTRICAL SYSTEM. Some 2016-2018 Ford and Lincoln vehicles equipped with SYNC 3 may exhibit the Android Auto Preference menu selection is not present after an update to version 3.0 software. In prior versions of SYNC 3 software this menu was present, however in version 3.0 software the Android Auto Preference menu will only show up once an Android Phone has been initially connected to SYNC. This an operating characteristic of the Android Auto application after the SYNC 3.0 update and no repairs should be attempted.
TSB 18-23212018-11-19. Service bulletin. ENGINE; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); ELECTRICAL SYSTEM. Some 2015-2018 Transit vehicles built on or before 24-Jul-2018 may exhibit various drivability concerns including difficulty starting, misfires and/or an illuminated MIL with diagnostic trouble codes (DTCs) P00BD, P1247, P1548, P061B, P2195, P2198, P2196, P2197, P0171, P0172, P0174, P0175, P0131 and/or P162F stored in the powertrain control module (PCM). This may be due to undesired water entry into the engine compartment directly over powertrain components. Follow the Service Procedure steps to correct the condition.
SSM 474442018-09-24. Service bulletin. ELECTRICAL SYSTEM. Some 2016-2018 Ford and Lincoln vehicles equipped with SYNC 3 not at the latest software level may exhibit Various Performance Related concerns such as Display Operation, Navigation, Voice Recognition, Phone Pairing, Applink, Travel Link, Slow System Response, etc. Check for SYNC software update under the OASIS Tab SYNC selection. If an update is available refer to WSM, Section 415-00 and update the APIM software. After Installation, complete pop-up appears, remove USB flash drive and install into IDS tool to update Ford database. Perform a complete ignition cycle by turning the key off for 5 minutes which is critical for a successful installation. If no updates are available or a blue or black screen is present after an update refer to WSM, Section 415-00 for diagnosis or SYNC 3 intermittent blank screen GSB for tips. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.
SSM 473972018-09-10. Service bulletin. ENGINE; ELECTRICAL SYSTEM. Some 2016-2018 Escape/Focus/Transit Connect vehicles equipped with a remote start system may exhibit an immediate engine shut off with or without diagnostic trouble code (DTC) P1594 stored in the BCM after using the remote start function to start the engine. If using FordPass, the app will indicate that the vehicle started successfully, but the engine may not have started or may start and then immediately shut off. Reprogram the BCM using the appropriate Ford scan tool or equivalent release 110.02 or higher. Make sure you are connected to the internet when entering module programming to obtain the latest updates. For claiming, use causal part 14A068 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
tsb18-22232018-09-10. Service bulletin. ELECTRICAL SYSTEM; FUEL SYSTEM, DIESEL; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:GAS RECIRCULATION VALVE (EGR VALVE). Some 2015-2018 Transit vehicles equipped with a 3.2L diesel engine may exhibit "Drive To Clean" maintenance messages and/or an illuminated malfunction indicator lamp (MIL) on with DTC P2459, P2463, and/or P246C. Vehicles may also exhibit frequent automatic exhaust regeneration attempts. This may be due to vehicles being used in a stationary or off-highway, low speed applications. If automatic regeneration attempts are unsuccessful, these symptoms may be a result of soot accumulation in the diesel particulate filter (DPF). These vehicles may benefit from operator commanded regeneration (OCR) capability so complete regeneration cycles may be performed in a stationary setting. Information only, follow the Service Procedure steps to correct the condition.
SSM 473802018-07-23. Service bulletin. EQUIPMENT; EQUIPMENT ADAPTIVE/MOBILITY; ELECTRICAL SYSTEM. Some 2016-2018 Ford and Lincoln vehicles with SYNC 3 may exhibit an intermittent blue or black screen. Check for SYNC software update under the OASIS Tab SYNC selection. If update is available refer to WSM, Section 415-00 and update APIM software. After Installation Complete pop-up appears, remove USB flash drive and install into IDS tool to update Ford database. Perform a complete ignition cycle by turning the key off for 5 minutes which is critical for a successful installation. If no updates are available or a blue or black screen is present after an update refer to WSM, Section 415-00 for diagnosis or SYNC 3 intermittent blank screen GSB for tips. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.
SSM 473792018-07-23. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT. Various 2016-2018 vehicles with SYNC 3 may experience a touch screen that does not respond to any input. Using the Professional Technician Society (PTS) website > OASIS tab > SYNC version, verify the vehicle SYNC software version. If the vehicle is at version 2.2 please update the module to the latest software level. After the software is updated make sure you shut the vehicle off, open the door for 2 minutes, then turn the key back on before testing the touch screen. If the software is at a later version than 2.2, proceed with normal diagnostics in Workshop Manual (WSM), Section 415-00. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.
SSM 471392018-05-21. Service bulletin. ELECTRICAL SYSTEM. Some 2018 Transit vehicles with a 3.2L engine built on or after 01-Jan-2018 may exhibit various starting or drivability issues along with various diagnostic trouble codes (DTCs). Before performing any diagnostic routines, as part of the standard visual checks, inspect the powertrain control module (PCM) connectors C1232B and C1232T to ensure they are fully seated, latched, and secured.
TSB18-20942018-05-21. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); ELECTRICAL SYSTEM. Some 2016-2018 Transit vehicles equipped with a 3.2L Duratorq diesel engine and built on or before 13-Feb-2018 may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P24A0 and/or P26A0 in the powertrain control module (PCM). Follow the Service Procedure steps to correct the condition.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.