WenmarOpen by Wenmar Pro

Service bulletins for the 2017 Ford Transit

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

217 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Only bulletins with component: Electrical system are shown. Show all

Bulletins, newest first
TSB 19-20162019-04-08. Service bulletin. ELECTRICAL SYSTEM; FUEL SYSTEM, GASOLINE; ENGINE. Some 2016-2018 Transit vehicles equipped with a 3.2L Duratorq diesel engine and built on or before 13-Feb-2018 may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P24A0 and/or P26A0 in the powertrain control module (PCM). Follow the Service Procedure steps to correct the condition.
SSM 478242019-04-01. Service bulletin. ELECTRICAL SYSTEM. Some 2015-2017 vehicles may experience a no crank concern due to a security access key table error. When attempting to program keys or perform a parameter reset, the procedure may fail and the Integrated Diagnostic System (IDS) scan tool may display an error 232: Key Table Not Allocated. If this error message is encountered, the Body Control Module (BCM) is internally faulted and requires replacement. For claiming, use causal part 15604 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.
TSB 19-20162019-04-01. Service bulletin. FUEL SYSTEM, GASOLINE; FUEL SYSTEM, DIESEL; ELECTRICAL SYSTEM. Some 2016-2018 Transit vehicles equipped with a 3.2L Duratorq diesel engine and built on or before 13-Feb-2018 may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P24A0 and/or P26A0 in the powertrain control module (PCM). Follow the Service Procedure steps to correct the condition.
SSM 477112019-03-04. Service bulletin. ELECTRICAL SYSTEM. Some 2016-2019 Ford and Lincoln vehicles equipped with SYNC 3 and a 6, 8 or 10 inch screen may show a pop-up message every key cycle that states 'SYNC can check for updates when connected to a WiFi network'. To remove the inconvenience of the pop-up the customer can either connect to a trusted WiFi network to complete the setup process or turn off WiFi in the WiFi settings located under the Settings menu. Adjusting the setting for the customer is not a warrantable defect.
SSM 476732019-01-07. Service bulletin. ELECTRICAL SYSTEM. Some 2016-2019 Transit vehicles equipped with a 3.2L diesel may indicate a blank PCM when connected to the Ford diagnostic scan tool. Do not replace the PCM. As a work around to access the PCM, remove the key from the ignition for 1 minute. Then remove the PCM relay in the battery junction box. Reinstall the PCM power relay, then put the key in the ignition and turn to on and attempt to access the PCM. Engineering is investigating the issue. Monitor OASIS for updates.
SSM 476712019-01-07. Service bulletin. ELECTRICAL SYSTEM. For 2015-2019 Transit vehicles, multiple fuse assemblies for the high current battery junction box are available for service. Do not replace the high current battery junction box assembly/wire harness to service an open fuse. Use part number BK2Z-14526-A for the 40 amp/100 amp/470 amp assembly, BK2Z-14526-B for the 2x60 amp/2x80 amp/3x100 amp/200 amp assembly, and BK2Z-14S411-A for the 60 amp MIDIù fuses on the outboard side of the driver seat base. Refer to Wiring Diagram Cell 11-7 for proper location.
SSM 475382018-12-03. Service bulletin. ELECTRICAL SYSTEM. Some 2016-2018 Ford and Lincoln vehicles equipped with SYNC 3 may exhibit the Android Auto Preference menu selection is not present after an update to version 3.0 software. In prior versions of SYNC 3 software this menu was present, however in version 3.0 software the Android Auto Preference menu will only show up once an Android Phone has been initially connected to SYNC. This an operating characteristic of the Android Auto application after the SYNC 3.0 update and no repairs should be attempted.
TSB 18-23212018-11-19. Service bulletin. ENGINE; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); ELECTRICAL SYSTEM. Some 2015-2018 Transit vehicles built on or before 24-Jul-2018 may exhibit various drivability concerns including difficulty starting, misfires and/or an illuminated MIL with diagnostic trouble codes (DTCs) P00BD, P1247, P1548, P061B, P2195, P2198, P2196, P2197, P0171, P0172, P0174, P0175, P0131 and/or P162F stored in the powertrain control module (PCM). This may be due to undesired water entry into the engine compartment directly over powertrain components. Follow the Service Procedure steps to correct the condition.
SSM 474442018-09-24. Service bulletin. ELECTRICAL SYSTEM. Some 2016-2018 Ford and Lincoln vehicles equipped with SYNC 3 not at the latest software level may exhibit Various Performance Related concerns such as Display Operation, Navigation, Voice Recognition, Phone Pairing, Applink, Travel Link, Slow System Response, etc. Check for SYNC software update under the OASIS Tab SYNC selection. If an update is available refer to WSM, Section 415-00 and update the APIM software. After Installation, complete pop-up appears, remove USB flash drive and install into IDS tool to update Ford database. Perform a complete ignition cycle by turning the key off for 5 minutes which is critical for a successful installation. If no updates are available or a blue or black screen is present after an update refer to WSM, Section 415-00 for diagnosis or SYNC 3 intermittent blank screen GSB for tips. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.
tsb18-22232018-09-10. Service bulletin. ELECTRICAL SYSTEM; FUEL SYSTEM, DIESEL; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:GAS RECIRCULATION VALVE (EGR VALVE). Some 2015-2018 Transit vehicles equipped with a 3.2L diesel engine may exhibit "Drive To Clean" maintenance messages and/or an illuminated malfunction indicator lamp (MIL) on with DTC P2459, P2463, and/or P246C. Vehicles may also exhibit frequent automatic exhaust regeneration attempts. This may be due to vehicles being used in a stationary or off-highway, low speed applications. If automatic regeneration attempts are unsuccessful, these symptoms may be a result of soot accumulation in the diesel particulate filter (DPF). These vehicles may benefit from operator commanded regeneration (OCR) capability so complete regeneration cycles may be performed in a stationary setting. Information only, follow the Service Procedure steps to correct the condition.
SSM 473802018-07-23. Service bulletin. EQUIPMENT; EQUIPMENT ADAPTIVE/MOBILITY; ELECTRICAL SYSTEM. Some 2016-2018 Ford and Lincoln vehicles with SYNC 3 may exhibit an intermittent blue or black screen. Check for SYNC software update under the OASIS Tab SYNC selection. If update is available refer to WSM, Section 415-00 and update APIM software. After Installation Complete pop-up appears, remove USB flash drive and install into IDS tool to update Ford database. Perform a complete ignition cycle by turning the key off for 5 minutes which is critical for a successful installation. If no updates are available or a blue or black screen is present after an update refer to WSM, Section 415-00 for diagnosis or SYNC 3 intermittent blank screen GSB for tips. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.
SSM 473792018-07-23. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT. Various 2016-2018 vehicles with SYNC 3 may experience a touch screen that does not respond to any input. Using the Professional Technician Society (PTS) website > OASIS tab > SYNC version, verify the vehicle SYNC software version. If the vehicle is at version 2.2 please update the module to the latest software level. After the software is updated make sure you shut the vehicle off, open the door for 2 minutes, then turn the key back on before testing the touch screen. If the software is at a later version than 2.2, proceed with normal diagnostics in Workshop Manual (WSM), Section 415-00. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.
SSM 470412018-06-11. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM:SOFTWARE; EQUIPMENT:ELECTRICAL; ELECTRICAL SYSTEM. Various 2016-2017 vehicles with SYNC 3 may experience a touch screen that does not respond to any input. Using the Professional Technician Society (PTS) website > OASIS tab > SYNC version, verify the vehicle SYNC software version. If the vehicle is at version 2.2 please update the module to the latest software level. After the software is updated make sure you shut the vehicle off, open the door for 2 minutes, then turn the key back on before testing the touch screen. If the software is at a later version than 2.2, proceed with normal diagnostics in Workshop Manual (WSM), Section 415-00. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.
SSM 472502018-05-21. Service bulletin. ELECTRICAL SYSTEM. As noted in FSA 17S34, loss of instrument cluster display can result from wiring corrosion and damage to the Trailer Relay Module on affected Transit vehicles. Complete the 17S34 service action as described prior to addressing any other customer reported symptoms. Vehicles that exhibit related wire harness damage must have the wire harness repaired or replaced prior to performing any additional diagnostic testing to avoid improperly condemning instrument clusters or other electronic modules.
SSM 472452018-05-21. Service bulletin. ELECTRICAL SYSTEM. Some 2015-2017 Transit vehicles may fail to program the BCM following replacement. To repair, follow BCM installation procedures in Workshop Manual (WSM), Section 419-10 using Integrated Diagnostic System (IDS) or Ford J2534 Diagnostic Software (FJDS) release 109.02 or higher. Make sure you are connected to the internet when entering module programming to obtain the latest updates. Calibration files may also be obtained at www.motorcraftservice.com. For claiming this programming procedure, use causal part 15604 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 472112018-05-21. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. Some 2016-2017 Ford and Lincoln vehicles equipped with SYNC 3 version 2.2 software may exhibit a blank screen after attempting to exit Valet mode. SYNC software updates are now available under the OASIS Tab SYNC selection. If update is available, refer to WSM Section 415-00 and update APIM software. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.
SSM 471672018-05-21. Service bulletin. ELECTRICAL SYSTEM. Various 2016-2017 vehicles with SYNC 3 may experience a touch screen that does not respond to any input. Using the Professional Technician Society (PTS) website > OASIS tab > SYNC version, verify the vehicle SYNC software version. If the vehicle is at version 2.2 please update the module to the latest software level. After the software is updated make sure you shut the vehicle off, open the door for 2 minutes, then turn the key back on before testing the touch screen. If the software is at a later version than 2.2, proceed with normal diagnostics in Workshop Manual (WSM), Section 415-00. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.
SSM 471232018-05-21. Service bulletin. ELECTRICAL SYSTEM. Some 2015-2017 Transit vehicles may fail to program the BCM following replacement. To repair, follow BCM installation procedures in Workshop Manual (WSM), Section 419-10 using Integrated Diagnostic System (IDS) or Ford J2534 Diagnostic Software (FJDS) release 108.06 or higher. Make sure you are connected to the internet when entering module programming to obtain the latest updates. Calibration files may also be obtained at www.motorcraftservice.com. Disregard DTC U0264 in the BCM and DTC U0010 in the Image Processing Module B (IPMB) if no observable rear parking aid camera concerns are present. For claiming this programming procedure, use causal part 15604 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
TSB18-20942018-05-21. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); ELECTRICAL SYSTEM. Some 2016-2018 Transit vehicles equipped with a 3.2L Duratorq diesel engine and built on or before 13-Feb-2018 may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P24A0 and/or P26A0 in the powertrain control module (PCM). Follow the Service Procedure steps to correct the condition.
SSM 470942018-05-14. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. Some 2015-2017 Transit vehicles may fail BCM installation programming when attempting to install a new BCM. The Technical Assistance Center and engineering teams are currently working to resolve this concern. If module programming is unsuccessful, do not attempt further repairs. Do not perform repeated key cycles or starting attempts. 30 key cycles on a blank module may result in a non-recoverable BCM when the programming concern is resolved. Monitor OASIS for updates.
SSM 469492018-01-29. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT. Some 2016-2017 Ford and Lincoln vehicles equipped with SYNC 3 version 2.2 software may exhibit a blank screen after attempting to exit Valet mode. SYNC software updates are now available under the OASIS Tab SYNC selection. If update is available, refer to WSM Section 415-00 and update APIM software. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.
SSM 469482018-01-29. Service bulletin. EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM); ELECTRICAL SYSTEM. Some owners of 2016-2017 Ford and Lincoln vehicles equipped with SYNC 3 may experience inoperative mobile device navigation applications. Mobile device navigation via AppLink requires SYNC 3 version 2.3 or higher for Apple iOS users. Mobile device navigation via AppLink is not currently available for Android users. SYNC software updates are now available under the OASIS Tab SYNC selection. If an update is available refer to WSM, Section 415-00 and update APIM software. SYNC 3 software upgrade to support these apps is not a warrantable repair per the Warranty And Policy Manual, Section 3, Warranty Coverages SYNC.
SSM 469472018-01-29. Service bulletin. EQUIPMENT; BACK OVER PREVENTION; ELECTRICAL SYSTEM; LANE DEPARTURE. Some 2016-2017 Ford and Lincoln vehicles with SYNC 3 may intermittently display an overhead image of a vehicle in the center of the SYNC touchscreen with no obstacle detection grids or warning chimes. SYNC may appear unresponsive when the overhead vehicle image is displayed. The vehicle image may intermittently display after shifting out of reverse or turning the vehicle off when in reverse. SYNC software updates are now available under the OASIS Tab SYNC selection. If an update is available, refer to WSM Section 415-00 and update the APIM software. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.
SSM 469232018-01-29. Service bulletin. ENGINE; ELECTRICAL SYSTEM. Some 2015-2017 Transit vehicles equipped with a 3.5L or 3.7l gasoline engine may exhibit an engine overheat condition or poor A/C cooling due to one or more of the 3 cooling fan fuses being open. If any one of the Battery Junction Box (BJB) fuses F30, F31, or F8 are open, replace F8 from a 20 amp to a 30 amp fuse (6E5Z-14526-BA), and service the F30 and F31 40 amp fuses (6E5Z-14526-CA) as needed. The wiring diagram has been updated. Failure to replace an open F8 with a 30amp fuse will cause F30 and F31 to open over time. Claim using causal part 9K499 if no other root cause is identified. Use applicable labor ops from section 10 of the SLTS manual for fuse replacement.
SSM 469002018-01-29. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); ELECTRICAL SYSTEM. Some vehicles may exhibit a no start condition with an illuminated malfunction indicator lamp (MIL) and a DTC P161A after PCM replacement. This may be due to the parameter reset procedure not being properly completed. To clear this DTC, use the Ford Integrated Diagnostic System (IDS) service tool or Ford J2534 Diagnostic Software, select - Toolbox - Body - Security - PATS Functions - Parameter Reset. Follow the on-screen instructions to complete the procedure. This procedure will transfer the existing Key ID information between the modules without the need of having 2 programmed PATS keys present. There is no need to program keys when the PCM is going to be replaced. Additional information can be found in the Workshop Manual (WSM), Section 419-01. Missing or lost keys are not warrantable.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.