WenmarOpen by Wenmar Pro

Service bulletins for the 2019 Ford Mustang

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

184 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

Only bulletins with component: Engine are shown. Show all

Bulletins, newest first
SSM 523352024-03-20. Service bulletin. ENGINE AND ENGINE COOLING. For 2015-2024 Ford and Lincoln vehicles equipped with turbocharged engines and customer concern of an engine oil leak, refer to Workshop Manual (WSM), Section 303-00 for oil leak inspection and testing methods. Ford has evaluated turbochargers replaced for oil leak symptoms and although oil may collect on the external surface of a turbocharger, it is extremely rare for a turbocharger assembly to be the root cause of the oil leak. Careful inspection of the turbocharger oil feed and drain tubes should be performed along with the recommended WSM procedures as needed. Warranty claims for turbocharger replacement going forward will be assessed.
SSM 523342024-03-20. Service bulletin. ENGINE AND ENGINE COOLING. Some 2011-2024 Mustang and F-150 vehicles equipped with a 5.0L engine may exhibit a tick tap and/or typewriter ticking noise at idle after an engine oil change. It is often referred to as typewriter noise because of its similarity to the sound of a mechanical typewriter. The noise in question may be heard on some engines when engine temperatures reach 150°F (65°C) or higher and engine speed is at idle up to approximately 1700 RPM. It can typically be heard at the front wheel well and is often isolated to the transmission bell housing or oil pan area. The typewriter noise tick rate can be faster or slower and is not detrimental to the engine function or durability and has no short or long term effects on the engine. This an operating characteristic of the 5.0L engine and no repairs should be attempted. This information along with an example audio clip has been added to the WSM Section 303-00 Engine System General Information > Diagnosis and Testing > Engine > PPT F > Step F2.
TSB 23-21322023-05-31. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM. Some 2018-2023 Mustang vehicles (non-Shelby GT-350) may exhibit various concerns with the active exhaust system. These may include Exhaust Mode Selection Not Available messages, and/or illuminated malfunction indicator lamp (MIL) with diagnostics trouble codes (DTCs) P26C5, P26C6, P26FE, P2BF9, P2BFB, P26C7, P2BF5, P2BF8, P2BFD and/or P2BFA. This may be due to an improperly seated exhaust system. To correct the condition, follow the Service Procedure to diagnose the tailpipe actuator.
TSB 22-23732023-01-31. Service bulletin. POWER TRAIN; ENGINE AND ENGINE COOLING. Some 2018-2019 Mustang vehicles equipped with a 5.0L engine and a manual transmission may exhibit an inability to drive the vehicle in first and/or second gear. This may be due to a broken 1-2 shift fork. To correct the condition, follow the Service Procedure to replace the 1st/2nd shift fork, the mainshaft 2nd gear, and the 1st/2nd gear synchronizer hub and sleeve.
TSB 22-22822022-10-31. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM. Some 2018-2022 Mustang vehicles (non-Shelby GT-350) may exhibit various concerns with the active exhaust system. These may include Drive Mode Not Available or Exhaust Mode Not Available messages, and/or illuminated malfunction indicator lamp (MIL) with diagnostics trouble codes (DTCs) P26C5, P26C6, P26FE, P2BF9, P2BFB, P26C7, P2BF5, P2BF8, P2BFD and/or P2BFA. This may be due to an improperly seated exhaust system. To correct the condition, follow the Service Procedure to diagnose the tailpipe actuator .
TSB 22-21402022-04-26. Service bulletin. ENGINE AND ENGINE COOLING; EQUIPMENT; EQUIPMENT ADAPTIVE/MOBILITY. Some 2015-2020 Mustang Shelby GT350/GT350R vehicles may exhibit a hesitation or surge in the vehicle with no diagnostic trouble codes (DTCs) present. This may be accompanied by an inoperative cruise control system. This may be due to a transmission output shaft flange nut that has come loose, allowing the output shaft tone ring to move in relation to the output shaft causing an erroneous signal. To resolve the condition, follow the Service Procedure steps to replace the output shaft flange nut.
SSM 500892021-09-28. Service bulletin. ENGINE AND ENGINE COOLING; FUEL SYSTEM, GASOLINE. Some 2017-2021 Ford and Lincoln vehicles equipped with 3.3L, 3.5L EcoBoost, or 5.0L engines may exhibit stalling, lack of power, low fuel rail pressure and/or DTCs P0087 or P008A after a repair was made that required the removal of the fuel line that connects the high-pressure fuel pump to the port injection rail, such as injector replacements or base engine repairs. This line must be installed in the correct orientation as it has an internal one-way check valve. To determine if the fuel line has been installed improperly, look at the position of the Oetiker clamp (stainless band clamped around the black fuel line). The clamp holds the one-way check valve in place and should be located closest to the end connected to the port injection rail. If the clamp is not closest to the port injection rail, remove and reinstall the line in the proper orientation.
SSM 498212021-06-01. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION; ENGINE AND ENGINE COOLING. Some 2015-2021 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTC) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK11 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 497612021-05-03. Service bulletin. ENGINE AND ENGINE COOLING. Some 2011-2021 Mustang and F-150 vehicles equipped with a 5.0L engine may exhibit a ticking noise at idle after an engine oil change. It is often referred to as typewriter noise because of its similarity to the sound of a mechanical typewriter. The noise in question may be heard on some engines when engine temperatures reach 150F (65Å’C) or higher and engine speed is at idle up to approximately 1700 RPMs. It can typically be heard at the front wheel well and is often isolated to the transmission bell housing or oil pan area. The typewriter noise is not detrimental to the engine function or durability and has no short or long term effects on the engine. This an operating characteristic of the 5.0L engine and no repairs should be attempted.
SSM 492102020-10-06. Service bulletin. ENGINE AND ENGINE COOLING. Some 2009-2020 Ford and Lincoln vehicles equipped with turbochargers may exhibit an oil leak from the turbocharger oil supply or return tubes, O-rings or 6.7L pedestal gasket. Although oil may collect on the turbocharger, it is very rare for a turbocharger to leak oil. To isolate the source of the leak, refer to Workshop Manual (WSM), Section 303-00 General Information > Diagnosis and Testing > Engine > Engine Oil Leaks - Fluorescent Oil Additive Method procedure. When an oil leak is present at a turbocharger oil supply or drain tube, remove the affected oil tube and inspect for damage, and replace the O-ring seals, pedestal gasket or oil tube as required. Refer to WSM, Section 303-04. For claiming, use the affected oil tube or pedestal gasket as the causal part and applicable labor operations in Sections 6 and 9 of the Service Labor Time Standards (SLTS) Manual.
TSB 19-22012019-09-06. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); ENGINE AND ENGINE COOLING. Some 2018-2019 Mustang vehicles equipped with a 5.0L engine may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P0420 and/or P0430. This may be due to the operation of the PCM. To correct the condition, follow the Service Procedure steps to replace the affected catalytic converter and reprogram the powertrain control module (PCM).
TSB19-21402019-06-05. Service bulletin. ENGINE AND ENGINE COOLING. Some 2018-2019 F-150 and Mustang vehicles equipped with a 5.0L engine built on or before 30-Apr-2019 may exhibit a chirping type noise from the upper engine front cover area at warm or hot idle. This noise may sound similar to a front engine accessory drive (FEAD) chirp noise. This may be due to the primary timing chain tensioner oil pressure relief valve. To correct the condition, replace the primary timing chain tensioners. Follow the Service Procedure.
TSB19-21442019-06-05. Service bulletin. ENGINE. Some 2018-2019 F-150 and Mustang vehicles equipped with a 5.0L engine may exhibit a light to moderate knocking type noise at idle (600-700 RPM) that is sometimes described as a quiet diesel type sound. The noise is usually more prominent on the passenger side of the vehicle toward the rear of the engine. As the engine comes up to operating temperature, the noise level increases slightly. This noise is not detrimental to engine function and has no short or long term effects on engine durability. This an operating characteristic of the 5.0L engine and no repairs should be attempted. Refer to the Service Procedure
SSM 479112019-05-07. Service bulletin. ENGINE. SSM 47911 - 2018-2019 F-150/Mustang - 5.0L - Chirping Noise From Engine Compartment At Idle Some 2018-2019 F-150 and Mustang vehicles equipped with a 5.0L engine may exhibit a chirping type noise from the upper right side of the engine at a warm or hot idle. This noise may sound similar to a front engine accessory drive (FEAD) chirp noise. If the noise persists with the FEAD belt removed and is isolated to the front cover area, this noise may be due to the primary timing chain tensioner. This noise will not result in any engine durability concerns. Do not attempt any repairs at this time. Engineering is investigating, monitor OASIS for updates.
SSM 479482019-05-07. Service bulletin. ENGINE. SSM 47948 - 2010-2019 Various Vehicles - Turbocharged Engines - Oil Supply Filter Replacement When Replacing The Turbocharger Or The Turbocharger Oil Supply Tube For 2010-2019 vehicles equipped with turbocharged engines, when diagnosing and/or replacing turbo related concerns, all steps within the Workshop Manual (WSM) procedure must be followed including replacement of all mandatory discarded parts. When specified in the WSM, the turbocharger oil supply filter must be replaced whenever the turbocharger or the turbocharger oil supply tube are replaced. Turbocharger bearing failure may occur if oil starvation occurs due to a restricted filter.
TSB 19-20492019-05-06. Service bulletin. POWER TRAIN; ENGINE AND ENGINE COOLING. Some 2019 Mustang and F-150 vehicles built on or before 8-Jan-2019 and equipped with a 5.0L engine may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P1289 and/or P017D stored in the powertrain control module (PCM). This may be due to cylinder head temperature (CHT) sensor. To resolve the condition, replace the CHT sensor.
18B34-S12019-03-04. Service bulletin. ENGINE. Certain 2018 Model Year F-150 and 2019 Mustang Vehicles equipped with 5.0L Engine - Throttle Body Replacement
TSB 18-23602019-03-04. Service bulletin. ENGINE; EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL; POWER TRAIN:AUTOMATIC TRANSMISSION. Some 2018 F-150 and 2018-2019 Mustang vehicles equipped with a 5.0L engine may exhibit an illuminated MIL with DTCs P0390 and/or P0394 stored in the powertrain control module (PCM). Follow the Service Procedure steps to correct the condition.
18B352019-01-07. Service bulletin. ENGINE. Certain 2018 Model Year F-150 and 2019 Mustang Vehicles equipped with 5.0L Engine - Throttle Body Replacement
SSM 476622019-01-07. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:TURBO/SUPERCHARGER. For 2010-2019 vehicles equipped with turbocharged engines, when diagnosing and/or replacing turbo related concerns, all steps within the Workshop Manual (WSM) procedure must be followed including replacement of all mandatory discarded parts. For all turbocharged engine applications, the turbocharger oil supply filter (6C683 gas engine/6L625 connector style or 6A968 diesel engine) must be replaced whenever the turbocharger or the turbocharger oil supply tube are replaced. Turbocharger bearing failure may occur if oil starvation occurs due to a restricted filter.
TSB 18-23552019-01-07. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR. Some 2018-2019 Mustang vehicles built on or before 17-Oct-2018 and equipped with a 2.3L engine may exhibit an illuminated MIL with DTC P0420. Follow the Service Procedure steps to correct the condition.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.