Service bulletins for the 2016 Ford F-650
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
140 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
By topic
| tsb18-2194 | 2018-09-10. Service bulletin. ENGINE AND ENGINE COOLING. Some 2015-2017 F-Super Duty vehicles equipped with a 6.7L engine built on or before 1-Jun-2017 may exhibit a leak from the coolant pump. Follow the Service Procedure steps to correct the condition. |
|---|---|
| 17M04-S1 | 2018-07-23. Service bulletin. EQUIPMENT; EQUIPMENT ADAPTIVE/MOBILITY; ENGINE AND ENGINE COOLING:ENGINE:DIESEL. Certain 2014-2016 Model Year F-250 ? F-550 and 2016 Model Year F-650/F-750 Vehicles, With 6.7L Diesel Engine - Crankcase Ventilation Oil Separator Assembly |
| SSM 47039 | 2018-06-11. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM. Some 2017 F-Super Duty, 2016-2017 F650-750 equipped with 6.7L diesel engines and 2015-2017 Transit equipped with 3.2L diesel engines may exhibit a MIL on with diagnostic trouble code (DTC) P206C stored in powertrain control module(PCM). This may be due to incorrect diesel exhaust fluid (DEF) concentration. Prior to performing Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test RJ, ensure DEF concentration is checked using Central Tools Refractometer tool number CEN3R201 and if DEF contamination is suspected use the Rotunda Hydrocarbon Test Kit tool number 328-480508. |
| SSM 47028 | 2018-06-11. Service bulletin. ENGINE. Some 2011-2018 F-Super Duty 6.7L diesel equipped vehicles may exhibit a ticking noise at idle after an engine oil change. It is often referred to as Typewriter Noise because of its similarity to the sound of a mechanical typewriter. When engine temperatures reach 150 Å?F (65 Å?C) or higher, (from engine idle up to approximately 1700 RPM's), this noise can typically be heard at the front wheel well and is often isolated to the transmission bell housing or oil pan area. Typewriter Noise is not detrimental to engine function or durability and has no short or long term effects on the engine. Do not attempt repairs to eliminate this noise. This noise is characteristic of the 6.7L diesel engine and will typically cease or diminish significantly within the oil change maintenance interval. |
| SSM 47006 | 2018-06-11. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM. All 2016 F-650 and F-750 vehicles built before 1-Apr-2016 requiring replacement of the reductant pump control module also requires replacement of the 14407 wiring harness which is included with the module service part. The current level service replacement module is not compatible with the harness on early build vehicles. |
| SSM 47041 | 2018-05-29. Service bulletin. EQUIPMENT:ELECTRICAL. Various 2016-2017 vehicles with SYNC 3 may experience a touch screen that does not respond to any input. Using the Professional Technician Society (PTS) website > OASIS tab > SYNC version, verify the vehicle SYNC software version. If the vehicle is at version 2.2 please update the module to the latest software level. After the software is updated make sure you shut the vehicle off, open the door for 2 minutes, then turn the key back on before testing the touch screen. If the software is at a later version than 2.2, proceed with normal diagnostics in Workshop Manual (WSM), Section 415-00. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual. |
| SSM 47039 | 2018-05-29. Service bulletin. POWER TRAIN. Some 2017 F-Super Duty, 2016-2017 F650-750 equipped with 6.7L diesel engines and 2015-2017 Transit equipped with 3.2L diesel engines may exhibit a MIL on with diagnostic trouble code (DTC) P206C stored in powertrain control module(PCM). This may be due to incorrect diesel exhaust fluid (DEF) concentration. Prior to performing Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test RJ, ensure DEF concentration is checked using Central Tools Refractometer tool number CEN3R201 and if DEF contamination is suspected use the Rotunda Hydrocarbon Test Kit tool number 328-480508. |
| SSM 47028 | 2018-05-29. Service bulletin. ENGINE AND ENGINE COOLING. Some 2011-2018 F-Super Duty 6.7L diesel equipped vehicles may exhibit a ticking noise at idle after an engine oil change. It is often referred to as Typewriter Noise because of its similarity to the sound of a mechanical typewriter. When engine temperatures reach 150 Å?F (65 Å?C) or higher, (from engine idle up to approximately 1700 RPM's), this noise can typically be heard at the front wheel well and is often isolated to the transmission bell housing or oil pan area. Typewriter Noise is not detrimental to engine function or durability and has no short or long term effects on the engine. Do not attempt repairs to eliminate this noise. This noise is characteristic of the 6.7L diesel engine and will typically cease or diminish significantly within the oil change maintenance interval. |
| SSM 47009 | 2018-05-29. Service bulletin. EQUIPMENT:ELECTRICAL. The Accessory (Wireless) Keyless Entry Keypad can only be used with vehicles that are factory built with Remote Keyless Entry (RKE). The master code for the Accessory (Wireless) Keyless Entry Keypad can be retrieved from FMCDealer - Parts and Service - Parts Product Line Information - Keys/Entry Devices - Aftermarket Keyless Entry Keypad Code Access. Access to this site is granted through Dealer Program Enrollment System (DPES) and Dealer Principal, General Manager or Parts and Service Director can authorize users. Once authorized the retrieval process for master code can be obtained. The master code for the Accessory Keyless Entry Keypad cannot be retrieved from the body control module(BCM) with a diagnostic tool. |
| SSM 47006 | 2018-05-29. Service bulletin. ENGINE AND ENGINE COOLING. All 2016 F-650 and F-750 vehicles built before 1-Apr-2016 requiring replacement of the reductant pump control module also requires replacement of the 14407 wiring harness which is included with the module service part. The current level service replacement module is not compatible with the harness on early build vehicles. |
| 18U12 | 2018-05-21. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION. Certain 2018 Model Year Escape and MKC Vehicles - Transmission Bell Housing Bolt TorqueCertain 2012-2016 Model Year F-450 ? F-750 and F-59 Commercial Stripped Chassis Vehicles Equipped with a 6.8L Engine - Camshaft Roller Follower Replacement |
| SSM 47266 | 2018-05-21. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM. Some 2016-2018 F-650/F-750 vehicles equipped with a 6.7L diesel engine may exhibit an illuminated malfunction indicator lamp (MIL) with DTC P20EE stored in the powertrain control module (PCM). When diagnosing this DTC, if pinpoint test (PPT) RD leads to Step RD27, proceed to Step RD28. This is due to PID NOx12 (NUM) incorrectly reading NOx11 (NUM) in the PCM. The NOx12 (NUM) PID will read the same as the NOx11 (NUM) PID. If the NOx Catalyst Conversion Efficiency Value PID reads less than 60% in Step RD28, replace the nitrogen oxides (NOx) sensor 12 and retest before replacing the selective catalyst reduction (SCR) catalyst. Engineering is investigating, monitor OASIS for updates. |
| TSB18-2127 | 2018-05-21. Service bulletin. FUEL SYSTEM, DIESEL. Some 2016-2017 F-650/F-750 vehicles equipped with a 6.7L diesel engine may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P012F, P0170, P218F, and/or a lack of performance at low speeds when heavily loaded. Follow the Service Procedure steps to correct the condition. |
| SSM 47110 | 2018-05-14. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM. Some 2017-2018 F-Super Duty/2016-2018 F650-750 with 6.7L diesel engines and 2015-2018 Transit with 3.2L diesel engines may exhibit a MIL on with diagnostic trouble code (DTC) P206C in the powertrain control module (PCM). This may be due to incorrect diesel exhaust fluid (DEF) concentration. Prior to performing Powertrain Control/Emissions Diagnosis (PC/ED) pinpoint test RJ, confirm DEF concentration using IDS to monitor REDUCT_CONC_MES. This PID reading may fluctuate between 31% and 34% indicating DEF concentration is correct. A concentration reading below 28% will set P206C and cause vehicle derate. This reading may also be checked using Central Tools Refractometer (CEN3R201) which should indicate a similar percentage as the PID. Low concentration of DEF is not a warrantable condition. If low concentration is suspected, drain fluid and replace with known good DEF before replacing any parts. |
| TSB18-2068 | 2018-05-14. Service bulletin. ELECTRICAL SYSTEM:IGNITION. Some 2016-2017 F-650/F-750 vehicles equipped with a 6.7L diesel engine may exhibit no starter engagement with no diagnostic trouble codes (DTCs) stored in the powertrain control module (PCM). This may be due to extended cranking attempts resulting in starter protection mode. Follow the Service Procedure steps to correct the condition. |
| 17B29 | 2018-01-29. Service bulletin. EQUIPMENT; ENGINE. Certain 2016-2017 Model Year F-650, F-750 and F-59 Vehicles with a 6.8L Engine - Cylinder Head Inspection and Replacement |
| SSM 46900 | 2018-01-29. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); ELECTRICAL SYSTEM. Some vehicles may exhibit a no start condition with an illuminated malfunction indicator lamp (MIL) and a DTC P161A after PCM replacement. This may be due to the parameter reset procedure not being properly completed. To clear this DTC, use the Ford Integrated Diagnostic System (IDS) service tool or Ford J2534 Diagnostic Software, select - Toolbox - Body - Security - PATS Functions - Parameter Reset. Follow the on-screen instructions to complete the procedure. This procedure will transfer the existing Key ID information between the modules without the need of having 2 programmed PATS keys present. There is no need to program keys when the PCM is going to be replaced. Additional information can be found in the Workshop Manual (WSM), Section 419-01. Missing or lost keys are not warrantable. |
| 17-2237 | 2018-01-29. Service bulletin. ELECTRICAL SYSTEM; ENGINE; FUEL SYSTEM, DIESEL. Some 2016 F-Super Duty/F-650/750 vehicles equipped with a 6.7L diesel engine or 2016 Transit vehicles equipped with a 3.2L diesel engine may exhibit an illuminated MIL with DTCs P24AE, P24B1, P24DA, P24C6 and/or P24C7 stored in the powertrain control module (PCM). Follow the Service Procedure steps to correct the condition. |
| 17-2234 | 2018-01-29. Service bulletin. ELECTRICAL SYSTEM; EXTERIOR LIGHTING. Some 2015-2016 F-Super Duty pickup vehicles equipped with a 6.7L engine may exhibit an illuminated malfunction indicator lamp (MIL) with DTCs P2201, P2459, P2463 and/or P246C. Reprogram the powertrain control module (PCM) to the latest calibration using Integrated Diagnostic System (IDS) or Ford J2534 Diagnostic Software (FJDS) release 106.01 or higher. Make sure you are connected to the internet when entering module programming to obtain the latest updates. Calibration files may also be obtained at www.motorcraftservice.com. |
| SSM 46890 | 2017-12-14. Service bulletin. FUEL SYSTEM, DIESEL; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Some 2017 F-Super Duty/2016-2017 F650-750 equipped with 6.7L diesel engines and 2015-2017 Transit equipped with 3.2L diesel engines may exhibit a MIL on with diagnostic trouble code (DTC) P206C stored in powertrain control module(PCM). This may be due to incorrect diesel exhaust fluid (DEF) concentration. Prior to performing Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test RJ, ensure DEF concentration is checked using Central Tools Refractometer tool number CEN3R201 and if DEF contamination is suspected use the Rotunda Hydrocarbon Test Kit tool number 328-480508. |
| tsb17-0068 | 2017-12-14. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Some 2016-2017 F-650/750 vehicles equipped with a 6.7L engine and built on or before 21-Aug-2017 may exhibit an illuminated MIL with DTC P203B in the powertrain control module (PCM) memory. This may be due to a low voltage condition reducing the ability of the integrated reductant level sensor to monitor reductant tank fluid levels. Follow the Service Procedure steps to correct the condition. |
| SSM 46085 | 2017-08-01. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:MANIFOLD/HEADER/MUFFLER/TAIL PIPE; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:GAS RECIRCULATION VALVE (EGR VALVE); ENGINE AND ENGINE COOLING:ENGINE:OTHER FUEL TYPES:TURBO/SUPERCHARGER; ENGINE AND ENGINE COOLING:COOLING SYSTEM:HOSES/LINES/PIPING/FITTINGS; ENGINE AND ENGINE COOLING; ENGINE AND ENGINE COOLING:COOLING SYSTEM:RADIATOR ASSEMBLY; ENGINE; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CRANKCASE (PCV); ENGINE AND ENGINE COOLING:COOLING SYSTEM; ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:TURBO/SUPERCHARGER; ENGINE AND ENGINE COOLING:ENGINE:DIESEL; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM; ENGINE AND ENGINE COOLING:ENGINE:GASOLINE; ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:BELTS AND ASSOCIATED PULLEYS; ENGINE AND ENGINE COOLING:ENGINE; ENGINE AND ENGINE COOLING:COOLING SYSTEM:FAN. The Powertrain Control/Emissions Diagnosis (PC/ED) manual has been revised for diagnosing electronic throttle bodies (ETBs). The ETC_ACT and ETC_DSD PIDs should not used to diagnose possible ETB concerns. The IDS has a limited refresh rate when reading these PIDs and cannot display quickly enough to validate a concern. The PCM automatically monitors these inputs more accurately and will set diagnostic trouble codes (DTCs) when appropriate. Using these PIDs for diagnostics will lead to inaccurate results and improper ETB replacements. If a concern is intermittent and no DTCs are present, refer to historical DTCs and the PC/ED, Section 3 No DTCs Present Index chart for further information. |
| SSM 46066 | 2017-08-01. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); ELECTRICAL SYSTEM. Some 2013-2017 F-Super Duty, 2015-2017 Transit and 2016-2017 F650-F750 vehicles equipped with a diesel engine may exhibit diagnostic trouble code (DTC) P2201 (NOX Sensor Circuit Range/Performance Bank 1 Sensor 1) in the powertrain control module (PCM). When repairing DTC P2201, refer to the online version of the powertrain control/emission diagnostic (PC/ED) manual for the latest diagnostics. The pinpoint test RD and diagnostic trouble code chart have been updated in section 4 and 5 for DTC P2201. |
| TSB 16-2033 | 2017-08-01. Service bulletin. EQUIPMENT:APPLIANCE:AIR CONDITIONER; ELECTRICAL SYSTEM. Some 2016-2017 F-650/750 vehicles equipped with a 6.8L engine and built on or before 8/2/2016 may exhibit intermittent A/C blowing warm air at idle or during low speed driving maneuvers. This may be due to intermittent disabling of the A/C compressor. Reprogram the powertrain control module (PCM) to the latest calibration using Integrated Diagnostic System (IDS) release 101.04 or higher. Make sure you are connected to the internet when entering module programming to obtain the latest updates. Calibration files may also be obtained at www.motorcraftservice.com. |
| SSM 46510 | 2017-08-01. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL; FUEL SYSTEM, DIESEL. Some 2017 F-Super Duty and 2016-2017 F650/F750 vehicles equipped with 6.7L engine may exhibit an inaccurate diesel exhaust fluid (DEF) level indicator or warning message with or without an illuminated malfunction indicator lamp (MIL) and diagnostic trouble code (DTC) P203B. This concern may be due to intermittent loss of signal from the reductant level sensor that is integrated into the reductant tank. If the applicable pinpoint test in the powertrain control/emission diagnostic (PC/ED) or workshop manual (WSM) directs replacement of the integrated reductant level sensor, do not attempt any repairs at this time and release the vehicle. Engineering is currently investigating this concern, monitor OASIS for updates regarding latest information and diagnostic direction. |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.