WenmarOpen by Wenmar Pro

Service bulletins for the 2022 Ford F-450

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

241 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Only bulletins with component: Transmission and driveline are shown. Show all

Bulletins, newest first
SSM 523142024-03-20. Service bulletin. POWER TRAIN. During service and repair requiring removal and replacement of a crankshaft bolt and/or crankshaft damper, achieving proper torque of the crankshaft pulley bolt is critical. Incorrect torque may allow the bolt to loosen resulting in the timing gear breaking and engine damage. Replacement of the bolt is critical to the repair and accurately following the installation procedure in the Workshop Manual (WSM) Section, 303-01 is extremely important. The bolt torque procedure can be found in the crankshaft front seal removal and installation procedure or in the engine assembly procedure.
SSM 519592023-11-03. Service bulletin. POWER TRAIN. When replacing the transmission case on a 2020-2022 F-Super Duty equipped with a 10R140 transmission, the new service case may not come equipped with the transmission fluid leveling plug. To achieve proper transmission fluid level, a new transmission fluid pan and gasket must be installed (service part PC3Z-7A194-A). Refer to the 2023 F-Super Duty Workshop Manual, Section 307-01B to properly set the transmission fluid level when using the newer transmission fluid pan.
SSM 517192023-06-21. Service bulletin. POWER TRAIN; ENGINE AND ENGINE COOLING. Some 2021-2023 F-Super Duty/E-Series vehicles equipped with a 6.2L, 6.8L or 7.3L gasoline engine may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P0457 and/or P0455 stored in the powertrain control module (PCM). This may be due to a improper fuel filler cap installation and/or outside contamination on the fuel cap sealing surface. The fuel filler cap requires multiple turns to seal properly and should be clean of any debris on sealing surface. Advise the customer to turn the fuel filler cap clockwise until there is at least one audible click to seal properly. If the DTCs return after the fuel filler cap is cleared of debris and properly seated, refer to Workshop Manual (WSM), Section 303-13 > pinpoint test HX.
SSM 516912023-06-16. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM; POWER TRAIN. 2011-2023 F-Super Duty and 2016-2024 F-650/F-750 vehicles equipped with a 6.7L engine may exhibit an elevated idle condition. During prolonged idle time, vehicles may experience this elevated idle to reduce unburned hydrocarbons from the SCR. The powertrain control module estimates hydrocarbon levels in the SCR and may increase idle speed to remove them. Idle speed will be increased to 1000 RPM for ambient temperatures near 26°C (80°F) and may increase to 1200 RPM at -40 °C (-40°F). Vehicles may exhibit exhaust smoke and diesel exhaust fluid smell during elevated idle condition. Exhaust smoke and smell condition will not affect reliability or durability of the engine. Power take-off (PTO) use and idle set point control will disable elevated speed. It is required that the operator monitor the vehicle and adhere to any Exhaust Filter warning messages.
SSM 516522023-05-31. Service bulletin. POWER TRAIN; BACK OVER PREVENTION:SOFTWARE. Some 2022 F-Super Duty vehicles equipped with a 6.7L engine, and built on 13-May-2022 and through 05-Aug-2022 at Kentucky Truck Plant or built on 13-Jun-2022 and through 09-Aug-2022 at Ohio Assembly Plant may exhibit an illuminated malfunction indicator lamp (MIL) with various diagnostic trouble codes (DTC) stored in the powertrain control module (PCM). While attempting to perform TSBs 23-2077, 23-2076, and/or 23-2082, vehicles that were produced without a particulate matter sensor will not show a PCM software update available in Ford Diagnosis and Repair System (FDRS). Refer to EFC10061 (MBG-2022-174N in Canada) and monitor OASIS for updates.
SSM 516482023-05-31. Service bulletin. POWER TRAIN; EQUIPMENT. Some 2020-2022 F-Super Duty vehicles equipped with a 6.7L engine may experience a lack of power due to snow packing of the engine air cleaner when operating in extremely snowy conditions. This may also be due to ice forming in the air intake while operating in temperatures below -22°F (-30°C). Diagnostic trouble code (DTC) P1548 may be present in the powertrain control module (PCM). To supplement heavy snow environment pre-filter service kit (service part LC3Z-9K635-AA), a front grill cover (service part NC3Z-19A413-A) is now available for service but is not a warrantable item. It is recommended that the front grill cover be removed at temperatures greater than 10°F (-12°C) and reinstall in subsequent winter seasons in order to maintain optimal vehicle performance.
SSM 516492023-05-23. Service bulletin. POWER TRAIN. Some 2021-2023 F-Super Duty vehicles equipped with a 10R140 transmission may exhibit harsh or delayed engagement/shift concerns. Most concerns may be addressed with the PCM/TCM Transmission Accelerated Main Control Break In Routine. Refer to Workshop Manual, Section 307-01, DTC Chart and/or Diagnosis By Symptom to identify the clutch(s) to be cycled. This routine cycles the shift solenoids and clutch control valves to remove contamination that may be sticking the valves and must be performed along with an adaptive learning drive cycle before attempting internal service. Although this routine was developed for low mileage vehicles, it has proven effective for resolving many shift and engagement symptoms across the life of the vehicle. For claiming, use causal part 7A100 and applicable labor operations in Section 7 of the Service Labor Time Standards Manual.
SSM 516292023-05-16. Service bulletin. EQUIPMENT:ELECTRICAL; POWER TRAIN. Some 2022 F-Super Duty vehicles equipped with a 6.7L engine, and built on 13-May-2022 and through 05-Aug-2022 at Kentucky Truck Plant or built on 13-Jun-2022 and through 09-Aug-2022 at Ohio Assembly Plant may exhibit an illuminated malfunction indicator lamp (MIL) with various diagnostic trouble codes (DTC) stored in the powertrain control module (PCM). While attempting to perform TSBs 23-2077, 23-2076, and/or 23-2082, vehicles that were produced without a particulate matter sensor will not show a PCM software update available in Ford Diagnosis and Repair System (FDRS). Refer to EFC10061 and monitor OASIS for updates.
TSB 23-20822023-04-04. Service bulletin. POWER TRAIN; BACK OVER PREVENTION:SOFTWARE. Some 2020-2022 F-Super Duty vehicles equipped with a 6.7L engine may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC) P0315, P054F, P054E, P2A00, P2A01, and/or P02ED stored in the powertrain control module (PCM). This may be due to the software in the PCM. To correct the condition, follow the Service Procedure to reprogram the PCM and the transmission control module (TCM).
TSB 23-20772023-04-04. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); BACK OVER PREVENTION:SOFTWARE. Some 2022 F-Super Duty vehicles equipped with a 6.7L engine may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) U3012 stored in the powertrain control module (PCM). This may be due to the software in the PCM. To correct the condition, follow the Service Procedure to reprogram the PCM and transmission control module (TCM).
TSB 23-20762023-04-04. Service bulletin. POWER TRAIN. Some 2020-2022 F-Super Duty vehicles equipped with a 6.7L engine may exhibit an illuminated malfunction indicator lamp (MIL) with cylinder injection pulse offset diagnostic trouble codes (DTC) P2B11, P2B13, P2B15, P2B17, P2B19, P2B1B, P2B1D, and/or P2B1F stored in the powertrain control module (PCM) after various fuel system repairs. This may be due to incorrect learned values in the PCM. To correct the condition, follow the Service Procedure to reprogram the PCM, reprogram the transmission control module (TCM), and perform the Reset Minimum Fuel Mass Adaptions All Cylinders.
SSM 513162023-02-02. Service bulletin. POWER TRAIN. Some 2020-2022 F-Super Duty vehicles equipped with a 6.7L engine may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P1674 stored in the transmission control module (TCM). This may be due to a discharged battery and/or low battery state of charge. Before performing normal diagnostics in Workshop Manual (WSM), Section 307-01, charge and test the battery/batteries using the Ford approved battery test equipment listed in the Ford Warranty and Policy Manual. Replace the battery/batteries if directed by the test equipment. Clear DTCs and perform the self test again. If P1674 returns, refer to WSM, Section 307-01 for normal diagnostics. If P1674 does not return, use the Report a Vehicle Concern link at the bottom of OASIS to submit a report that will assist with the engineering investigation.
TSB 22-24502022-12-02. Service bulletin. POWER TRAIN; POWER TRAIN:AUTOMATIC TRANSMISSION:INTERNAL:SHAFT:OUTPUT; UNKNOWN OR OTHER. Some 2022 F-Super Duty vehicles built on or before 31-Jul-2022 equipped with a 10R140 automatic transmission may exhibit a fluid leak from the selector shaft seal. This may be caused by a crack in the manual shaft. To correct this condition, follow the Service Procedure to replace the manual shaft, the manual shaft-to-sensor roll pin and the selector shaft seal.
SSM 509772022-08-02. Service bulletin. POWER TRAIN:MANUAL TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); EQUIPMENT; FUEL SYSTEM, GASOLINE:STORAGE:TANK ASSEMBLY:FILLER PIPE AND CAP; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Some 2021-2022 F-Super Duty and 2021-2023 E-Series vehicles equipped with a 6.2L or 7.3L gasoline engine may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P0457 stored in the powertrain control module (PCM). This may be due to a loose fuel filler cap. The fuel filler cap design has changed, requiring multiple turns to seal properly. Advise the customer to turn the fuel filler cap clockwise until there is at least one audible click to seal properly. For further diagnostics, refer to Workshop Manual (WSM), Section 303-13 - pinpoint test HX.
SSM 509552022-07-29. Service bulletin. POWER TRAIN. Some 2021-2022 F-Super Duty vehicles equipped with a 10R140 transmission may exhibit harsh or delayed engagement/shift concerns. Most concerns may be addressed with the PCM/TCM Transmission Accelerated Main Control Break In Routine. Refer to Workshop Manual, Section 307-01, DTC Chart and/or Diagnosis By Symptom to identify the clutch(s) to be cycled. This routine cycles the shift solenoids and clutch control valves to remove contamination that may be sticking the valves and must be performed along with an adaptive learning drive cycle before attempting internal service. Although this routine was developed for low mileage vehicles, it has proven effective for resolving many shift and engagement symptoms across the life of the vehicle. For claiming, use causal part 7A100 and applicable labor operations in Section 7 of the Service Labor Time Standards Manual.
TSB 22-22672022-07-11. Service bulletin. POWER TRAIN. Some 2022 F-Super Duty vehicles built on or before 16-May-2022 equipped with a 6.7L engine may exhibit harsh 3-2 and/or 2-1 downshifts when coming to a stop in tow/haul mode or when using engine brake mode. This may be due to the software in the transmission control module (TCM). To correct the condition, follow the Service Procedure to reprogram the TCM and powertrain control module (PCM)
TSB 22-22522022-07-01. Service bulletin. POWER TRAIN. Some 2022 F-Super Duty four-wheel drive (4WD) pickup vehicles built on or before 16-May-2022 equipped with a 6.7L engine may exhibit a momentary, slight grinding type noise prior to the 4-3 downshift while coasting without the brakes applied. This may be due to the software in the transmission control module (TCM). To correct the condition, follow the Service Procedure to reprogram the TCM and powertrain control module (PCM).
SSM 508642022-06-29. Service bulletin. POWER TRAIN. Some 2020-2022 F-Super Duty vehicles may exhibit a condition where the vehicle will not shift out of park (P). Diagnostic trouble codes (DTC) C0040 and/or P0504 may also be present. Reference TSB 22-2044 to make sure that no water or corrosion is present in the battery junction box (BJB). If Pinpoint Test A: Brake Shift Interlock in Workshop Manual (WSM), Section 307-05 leads to a concern with circuit SBP07 (white/red), remove the left side scuff plate from the floor and inspect circuit SBP07 for any damage. If damage is present, repair as necessary. Refer to Wiring Diagram, Cell 005. Submit a Report a Vehicle Concern form at the bottom of the OASIS screen and attach any available pictures to assist with the engineering investigation.
SSM 508482022-06-29. Service bulletin. POWER TRAIN. Some 2020-2022 F-Super Duty vehicles may exhibit a condition where the vehicle will not shift out of park (P). Diagnostic trouble codes (DTC) C0040 and/or P0504 may also be present. Reference TSB 22-2044 to make sure that no water or corrosion is present in the battery junction box (BJB). If Pinpoint Test A: Brake Shift Interlock in Workshop Manual (WSM), Section 307-05 leads to a concern with circuit SPB07 (white/red), remove the left side scuff plate from the floor and inspect circuit SPB07 for any damage. If damage is present, repair as necessary. Refer to Wiring Diagram, Cell 005. Submit a Report a Vehicle Concern form at the bottom of the OASIS screen and attach any available pictures to assist with the engineering investigation.
TSB 22-21992022-05-24. Service bulletin. POWER TRAIN. Some 2021-2022 F-250 vehicles equipped with a 6R100 transmission, four-wheel drive (4WD), and built on 01-Feb-2021 and through 16-May-2022 may exhibit a metallic grinding noise from the rear of the vehicle under light acceleration between 23-33 mph (37-53 km/h). The noise is most prevalent in 3rd and 4th gear when the vehicle is warm. This may be due to normal driveline noise transmitting through the driveshaft. To correct the condition, follow the Service Procedure to replace the rear axle drive pinion flange, rear pinion seal, and reprogram the powertrain control module (PCM).
SSM 507422022-05-14. Service bulletin. POWER TRAIN; ELECTRICAL SYSTEM. Some 2020-2022 F-Super Duty vehicles may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P0073 for the ambient air temperature sensor stored in the powertrain control (PCM). When performing pinpoint test BF in Workshop Manual (WSM), Section 413-01, the ambient air temperature sensor/outside air temperature display reset procedure has been added to the Ford Diagnostic Repair System (FDRS) diagnostic scan tool. Depending on how the vehicle is equipped, run the FCIM or HVAC. Reset the Outside Air Temperature Sensor Learned Values application. Clear DTCs and retest after performing the reset procedure.
SSM 507122022-05-03. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION. Some 2022 F-Super Duty four-wheel drive (4WD) pickup vehicles equipped with a 6.7L engine may exhibit a momentary, slight grinding type noise prior to the 4-3 downshift while coasting without the brakes applied. This condition does not affect vehicle durability. Replacement of the transmission or other components will not resolve this condition and engineering is currently working on a solution which is expected to be available by June 2022. Let the customer know they can continue to drive the vehicle and schedule a follow-up appointment for June 2022. Monitor OASIS for updates and confirm that the service appointment is going forward once the repair becomes available.
SSM 506462022-04-13. Service bulletin. ENGINE AND ENGINE COOLING; POWER TRAIN; ELECTRICAL SYSTEM. Some 2020-2022 F-Super Duty vehicles equipped with a 6.7L engine may exhibit an illuminated malfunction indicator lamp (MIL) with cylinder injection pulse offset diagnostic trouble codes (DTC) P2B11, P2B13, P2B15, P2B17, P2B19, P2B1B, P2B1D, and/or P2B1F stored in the powertrain control module (PCM) after various fuel system repairs. This may be due to incorrect learned values in the PCM. To correct the condition, allow the engine to idle for at least 6 minutes with the engine at normal operating temperature. Clear DTCs and retest. PCM replacement is not necessary for this condition.
SSM 506402022-04-04. Service bulletin. POWER TRAIN. Some 2022 F-Super Duty vehicles equipped with a 6.7L diesel engine and a 10R140 automatic transmission may exhibit harsh 3-2 and/or 2-1 downshifts when coming to a stop in tow/haul mode or when using engine brake mode. Because this is related to a software issue, replacement of the transmission or other components will not resolve this condition and engineering is currently working on a software update which is expected to be available by the end of June 2022. In the interim Perform TSB 22-2015, steps 10-15 only, and evaluate if the concern is resolved. If the concern is still present, let the customer know they can continue to drive the vehicle and schedule a follow-up appointment for June 2022. Monitor OASIS for updates and confirm that the service appointment is going forward once the repair becomes available.
SSM 506362022-03-29. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE:SOFTWARE; ENGINE AND ENGINE COOLING; EQUIPMENT. 2011-2022 F-Super Duty and 2016-2023 F-650/F-750 vehicles equipped with a 6.7L engine may exhibit an elevated idle condition. During prolonged idle time, vehicles may experience this elevated idle to reduce unburned hydrocarbons from the SCR. The powertrain control module estimates hydrocarbon levels in the SCR and may increase idle speed to remove them. Idle speed will be increased to 1000 RPM for ambient temperatures near 26°C (80°F) and may increase to 1200 RPM at -40 °C (-40°F). Vehicles may exhibit exhaust smoke and diesel exhaust fluid smell during elevated idle condition. Exhaust smoke and smell condition will not affect reliability or durability of the engine. Power take-off (PTO) use and idle set point control will disable elevated speed. It is required that the operator monitor the vehicle and adhere to any Exhaust Filter warning messages.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.