Service bulletins for the 2021 Ford F-250
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
242 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
By topic
Only bulletins with component: Brakes are shown. Show all
| SSM 54448 | 2026-01-06. Service bulletin. SERVICE BRAKES. Some 2017-2026 F-Super Duty vehicles may exhibit a pull/drift condition during braking. This may be due to the brake pads needing to be broken in. Repeated, heavy brake applications may assist to resolve the pull/drift condition. The Workshop Manual, Section 206-00 Symptom Chart for vehicle pulls or drifts during braking has been updated to reflect this information. |
|---|---|
| SSM 51432 | 2023-04-04. Service bulletin. PARKING BRAKE. Some 2020-2022 F-Super Duty vehicles may exhibit a condition where the vehicle will not shift out of park (P). Diagnostic trouble codes (DTC) C0040 and/or P0504 may also be present. Reference TSB 22-2044 to make sure that no water or corrosion is present in the battery junction box (BJB). If Pinpoint Test A: Brake Shift Interlock in Workshop Manual (WSM), Section 307-05 leads to a concern with circuit SBP07 (white/red), remove the left side scuff plate from the floor and inspect circuit SBP07 for any damage. If damage is present, repair as necessary. Refer to Wiring Diagram, Cell 005. Submit a Report a Vehicle Concern form at the bottom of the OASIS screen and attach any available pictures to assist with the engineering investigation. |
| SSM 51261 | 2023-01-06. Service bulletin. SERVICE BRAKES. Some Ford and Lincoln vehicles may exhibit noise when the brakes are applied. When diagnosing and repairing brake noise conditions, use the Workshop Manual (WSM) and the appropriate pinpoint test in section 206-00. The brake rotors should only be machined if directed by the WSM because one or more of the following conditions are present on the braking surface: scoring, excessive corrosion/rust or pitting, bluing/discoloration and/or heat spots. For additional information, refer to WSM section 206-00. |
| SSM 51120 | 2022-10-11. Service bulletin. SERVICE BRAKES, HYDRAULIC. Some Ford and Lincoln vehicles may exhibit noise when the brakes are applied. When diagnosing and repairing brake noise conditions, use the Workshop Manual (WSM) and the appropriate pinpoint test in section 206-00. The brake rotors should only be machined if directed by the WSM because one or more of the following conditions are present on the braking surface: scoring, excessive corrosion/rust or pitting, bluing/discoloration and/or heat spots. For additional information, refer to WSM section 206-00. |
| SSM 50718 | 2022-05-03. Service bulletin. SERVICE BRAKES. Some 2017-2022 F-Super Duty vehicles may exhibit a pull / drift condition during braking. This may be due to the brake pads needing to be broken in. The Workshop Manual, Section 206-00 Symptom Chart for vehicle pulls or drifts during braking has been updated to reflect this information. |
| SSM 50364 | 2021-12-26. Service bulletin. SERVICE BRAKES, HYDRAULIC; ELECTRICAL SYSTEM. Some 2021-2022 F-Super Duty vehicles may exhibit an illuminated anti-lock brake system (ABS) warning lamp due to various diagnostic trouble codes or faults. If the ABS module does not respond to the Ford Diagnosis and Repair System (FDRS) scan tool during normal diagnostics, make sure all related connectors are fully seated. If no connector concerns are found, remove the FDRS scan tool from the vehicle and disconnect the vehicle battery cables for 10 minutes. Reconnect the battery cables and attempt to re-establish communication with the ABS module using the FDRS scan tool. |
| SSM 50064 | 2021-09-04. Service bulletin. SERVICE BRAKES, ELECTRIC:SOFTWARE/PROGRAMMING. Some 2013-2021 Ford and Lincoln vehicles may exhibit noise when the brakes are applied. When diagnosing and repairing brake noise conditions, use the Workshop Manual (WSM) and the appropriate pinpoint test in section 206-00. The brake rotors should only be machined if directed by the WSM because one or more of the following conditions are present on the braking surface: scoring, excessive corrosion/rust or pitting, bluing/discoloration and/or heat spots. For additional information, refer to WSM section 206-00. |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.