WenmarOpen by Wenmar Pro

Service bulletins for the 2018 Ford F-250

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

251 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Only bulletins with component: Transmission and driveline are shown. Show all

Bulletins, newest first
TSB 19-23152019-11-05. Service bulletin. ENGINE AND ENGINE COOLING; POWER TRAIN; ELECTRICAL SYSTEM. Some 2017-2019 F-Super Duty vehicles built on or before 1-Aug-2018 equipped with a 6.7L engine may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P21DD, P204C, P21CD and/or U02A2 in the powertrain control module (PCM). This may be due to water intrusion within connectors C3613 and/or C4851 on the reductant harness going to the reductant pump/heater assembly and the reductant level sensor/quality module. To correct the condition, follow the Service Procedure steps to replace the reductant harness, the reductant pump/heater assembly and/or the reductant tank.
TSB 19-22312019-08-06. Service bulletin. POWER TRAIN. Some 2017-2019 F-Super Duty vehicles equipped with a 6.7L engine may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P1291, P1292, P0191 and/or P06A6. This may be due to an engine harness chafe on the powertrain control module (PCM) bracket. Before completing Powertrain Control/Emissions Diagnosis (PC/ED) Manual pinpoint tests, follow the Service Procedure steps.
SSM 479762019-06-07. Service bulletin. POWER TRAIN. On vehicles equipped with an automatic transmission it is imperative that the converter pilot hub be greased with Motorcraft Multi-Purpose Grease Spray XL-5-A even if grease was not applied from the factory. Also verify that the engine/transmission alignment dowel pins are present as well as the engine crankshaft dowel pin, if equipped, when installing the transmission. Failure to adequately lubricate the converter hub greatly increases the likelihood of the flexplate cracking in the future. Missing dowels may cause a misalignment issue also resulting in a premature failure. Refer to Workshop Manual (WSM), Section 307-01.
TSB19-21602019-06-05. Service bulletin. ENGINE AND ENGINE COOLING; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Some 2017-2019 F-Super Duty vehicles equipped with a 6.7L engine built on or before 9-Jan-2019 may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P2074, P0401, P0402 and/or P0170. This may be due to various strategies within the powertrain control module (PCM) software. To resolve this condition, follow the Service Procedure steps to reprogram the PCM and perform a mass air flow (MAF) parameter reset. Follow the service procedure steps to correct the condition.
SSM 479032019-05-07. Service bulletin. POWER TRAIN. SSM 47903 - 2018-2019 F-150/F-Super Duty/Transit - Rear Axle Pinion Seal Fluid Leak/Seepage Some 2018-2019 F-150, F-Super Duty, and Transit vehicles may exhibit the appearance of a fluid leak or seepage from the rear axle pinion seal. The appearance of a fluid leak or seepage on a vehicle with less than 500 miles or less than 3 months in service may not be due to a failed rear axle pinion seal. The appearance of fluid around the seal may be from the axle assembly being shipped to the vehicle assembly plant with the pinion facing down. To determine if a leak is present, clean the seal area of any residual lubricant and visually inspect the pinion seal for leaks or damage in the seal contact area or dust slinger on the pinion flange dust shield. If no concerns are found, run the vehicle on a hoist in DRIVE at idle speeds for 10 minutes to allow the fluid to circulate and recheck for signs of leakage.
SSM 478232019-04-08. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); ENGINE. Various 2013-2019 vehicles may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P264F after powertrain control module (PCM) replacement. This DTC indicates that the engine serial number (ESN) must be programmed into the PCM. The ESN is located on PTS> OASIS> Features> Engine Serial Number. Once the ESN is obtained from the historical vehicle bill of materials (HvBOM), it can be programmed into the PCM using the appropriate Ford diagnostic scan tool. Navigate to the toolbox tab> powertrain menu> Service Functions> ESN.
TSB 19-20532019-04-02. Service bulletin. ENGINE AND ENGINE COOLING; POWER TRAIN. Some 2017-2019 F-Super Duty chassis cab/dual rear wheel (DRW) pickup vehicles and 2016- 2019 F-650/F-750 vehicles equipped with a 6.7L engine may exhibit an oil consumption concern in applications where the engine is idled for extended periods of time. This may be due to high crankcase pressure as a result of the crankcase ventilation filter element becoming restricted. To resolve the concern, replace the crankcase vent oil separator. The new crankcase vent oil separator appears different from the old crankcase vent oil separator as it no longer includes a serviceable filter element.
SSM 478232019-04-01. Service bulletin. POWER TRAIN. Various 2013-2019 vehicles may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P264F after powertrain control module (PCM) replacement. This DTC indicates that the engine serial number (ESN) must be programmed into the PCM. The ESN is located on PTS> OASIS> Features> Engine Serial Number. Once the ESN is obtained from the historical vehicle bill of materials (HvBOM), it can be programmed into the PCM using the appropriate Ford diagnostic scan tool. Navigate to the toolbox tab> powertrain menu> Service Functions> ESN.
SSM 476562019-01-07. Service bulletin. ELECTRICAL SYSTEM; POWER TRAIN. Some 2018-2019 F-Super Duty vehicles equipped with a 6.7L engine built on 1-Dec-2017 and through 1-Aug-2018 may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P2122, P2127, U0401, U0109, P0480, P008A, P025C, P027A and/or P064A. This may be due to powertrain control module (PCM) connector C1232B not being properly seated to the PCM.
SSM 475422018-12-03. Service bulletin. POWER TRAIN. Some 2017-2019 F-Super Duty/2018 F-150 vehicles equipped with the 6.7L or 3.0L engines may exhibit an illuminated malfunction indicator lamp (MIL) with DTC P208E in the powertrain control module (PCM). When performing pinpoint test RK, the results of the selective catalyst reductant (SCR) dosing measurement test (RK7) may be zero or below the specified 40-50mL requirement due to urea crystals plugging the DEF injector nozzle. If the measurement is below this specified amount, perform pinpoint test step RK7 two additional times. If the specified amount is met, reinstall the reductant injector. If after three attempts the dosing measurement remains below the specified amount, the DEF injector should be replaced. The DEF pump should not be replaced for DTC P208E. Engineering is investigating. Monitor OASIS for updates.
SSM 475412018-12-03. Service bulletin. POWER TRAIN. Some 2017-2019 F-Super Duty vehicles equipped with a 6.7L engine may exhibit an illuminated MIL with only DTC P2074 stored in the powertrain control module (PCM). Do not replace the PCM or mass air flow (MAF) sensor for this concern. Instead perform a MAF parameter reset under: Toolbox - Powertrain - Service Functions - Reset/Clear Specified Function - Reset/Clear Functions - MAF Sensor. Engineering is investigating. Monitor OASIS for updates.
SSM 471702018-05-21. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION. Some vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK11 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in section 10 of the Service Labor Time Standards (SLTS) Manual.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.