WenmarOpen by Wenmar Pro

Service bulletins for the 2020 Ford F-150

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

247 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

Bulletins, newest first
SSM 494772021-02-04. Service bulletin. EQUIPMENT. Some 2015-2021 F-150, 2016-2018 MKX, 2019-2021 Nautilus, 2015-2021 Edge, 2017-2019 Fusion, 2017-2020 MKZ And 2017-2020 Continental vehicles equipped with a 2.7L/3.0L EcoBoost engine may appear to have a low engine oil level if the proper procedures are not followed. Refer to the Owner's Manual > Maintenance > Engine oil check section. When checking the engine oil level after shutting off the engine wait at least 15 minutes prior to checking in order to allow the oil to drain back to the oil pan. The engine oil level can be checked immediately if the engine has not been started. When changing the engine oil the engine needs to be at normal operating temperature and the oil filter removed before draining the oil. Allow the oil pan to drain completely for up to 5 minutes. Check oil level after filling by following the oil level check procedure.
TSB 20-24232021-01-05. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; ELECTRICAL SYSTEM; POWER TRAIN. Some 2018-2020 F-150/Navigator vehicles equipped with a 3.5L EcoBoost High-Output engine and built on or before 11-Sept-2020 may exhibit excessive oil consumption with no visible oil leaks with or without diagnostic trouble code (DTC) P0365 and/or P0369. To correct the condition, follow the Service Procedure steps to reprogram the powertrain control module (PCM) and if necessary, replace the engine valve covers.
TSB 20-23852020-12-05. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT. Some 2020 F-150 Lariat vehicles equipped with the snow plow prep package may exhibit the snow plow button illuminating when you press the start/stop deactivation button, and the start/stop deactivation indicator illuminating when you press the snow plow button. Both features otherwise function correctly, and the correct messages illuminate in the message center when pressing either button. This may be due to incorrect switch circuitry. To correct the condition, follow the Service Procedure steps to swap circuit pin locations.
20B392020-12-05. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM; ELECTRICAL SYSTEM:ADAS:HUD:CAMERA/SENSOR. Certain 2020 Model Year Multiple Vehicle Lines Front View and Center High Mount Stop Lamp Camera Improper Function In some of the affected vehicles, insufficient electrical conductivity within the Printed Circuit Board (PCB) internal to the camera may lead to intermittent front view or Center High Mount Stop Lamp (CHMSL) camera operation. This could result in a blank or distorted image from the front of the vehicle or of the truck bed Dealers are to replace the front view camera or the CHMSL camera following the dealer bulletin technical information. This service must be performed on all affected vehicles at no charge to the vehicle owner.
SSM 493182020-12-04. Service bulletin. EQUIPMENT. For 2011-2020 F-150/Mustang vehicles equipped with a 5.0L engine when installing a replacement secondary timing chain tensioner (6K254) or secondary timing chain guide (6K297), it is necessary to replace both components as a pair, using the latest level parts. Make sure to use secondary timing chain tensioner part number ML3Z-6K254-A and secondary timing chain guide part number ML3Z-6K297-A.
SSM 493552020-12-04. Service bulletin. EQUIPMENT; ENGINE AND ENGINE COOLING. Some 2015-2020 F-150 and 2018-2020 Expedition/Navigator vehicles equipped with a 3.5L/2.7L EcoBoost engine and four-wheel drive (4WD) may exhibit an intermittent grinding type noise while driving in two-wheel drive (2WD), most commonly on acceleration. This noise could appear to be turbocharger related. After engineering analysis of returned turbochargers that have been replaced for this condition, no concerns were identified with the turbochargers. The grinding type noise may be related to the 4WD system integrated wheel ends (IWE). To aid in diagnosis, shift the vehicle to 4WD and attempt to verify the condition. If the grinding noise no longer occurs with the vehicle in 4WD a IWE vacuum system and/or mechanical fault may be present.
TSB 20-23632020-11-05. Service bulletin. ELECTRICAL SYSTEM. Some 2019 MKZ, 2019-2020 EcoSport/Mustang/Continental/Fusion/F-150/Transit Connect/Ranger/Edge/Nautilus and 2020 Escape/Corsair/Aviator/Explorer/Expedition/Navigator/F-Super Duty vehicles with SYNC 3 may experience various SYNC performance related concerns. To correct the condition, follow the Service Procedure.
TSB 20-23592020-11-05. Service bulletin. LATCHES/LOCKS/LINKAGES; EQUIPMENT. Some 2020 F-150/F-Super Duty vehicles built on 18-May-2020 and through 30-Jun-2020 may exhibit a concern where the right rear door lock is inoperative but the manual lock rod works. This may be due to stack up tolerances of the handle, cable and latch. To correct the condition, follow the Service Procedure to remove the cable barrel sleeve.
TSB 20-23072020-11-05. Service bulletin. ELECTRICAL SYSTEM; WHEELS; EQUIPMENT. Some 2003-2020 Expedition/Navigator and 2006-2020 F-150 vehicles equipped with TOD transfer cases may exhibit grinding/clicking/ratcheting noise from the front wheel area. This may be due to partial engagement of the integrated wheel ends (IWE). To correct this condition, follow the Service Procedure steps to remove and cap the vacuum supply line.
SSM 492922020-11-04. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Some 2018-2020 Ford and Lincoln vehicles may exhibit inoperative remote features via the Ford Pass/Lincoln Way mobile app, incomplete user authorization, no modem electronic serial number (ESN) displayed or DTCs U2100 and/or B156D in the telematics control unit (TCU). These symptoms may persist even after performing a TCU software update and/or replacement. To correct this condition, start a new session with the latest version of the appropriate diagnostic scan tool and perform a PMI on the TCU. If issues persist, open a hotline assistance request and include the IDS version (if applicable) used to perform the PMI and the Authorization Status PID value in the TCU datalogger. For claiming use causal part 14H092 and applicable labor times in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 492842020-11-04. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL; ELECTRICAL SYSTEM:SOFTWARE. Some 2018-2020 Ford and Lincoln vehicles equipped with TCU and WiFi Hotspot, May display Vehicle Hotspot feature not enabled on this vehicle when attempting to enter the Hotspot menu. When using the FordPass/Lincoln Way application, the customer may receive a message saying Wi-Fi has been disabled from this vehicle. Check the vehicle specifications or vehicle build information for the mfal code. If mfal = WAFAC or WAFAB do not replace the TCU, engineering is currently investigating this condition. Inform customers Ford is developing a software fix that is expected in early January. In the interim, let the customer know they can continue to drive the vehicle and schedule a follow-up appointment with the customer for early January. Once the update becomes available, contact the customer and confirm the service appointment is going forward. Monitor OASIS for updates.
SSM 490992020-11-04. Service bulletin. POWER TRAIN; POWER TRAIN:TRANSFER CASE (4-WHEEL DRIVE). 2019-2020 F-150 vehicles equipped with four-wheel drive (4WD) have a revised transfer case control module (TCCM) strategy that will affect integrated wheel end (IWE) operation after initial start-up. The TCCM will not energize the solenoid to supply vacuum to the IWEs after the initial key cycle and a driven gear is selected. The IWEs will remain engaged for 0.8 km (0.5 mi) when the temperature is above 0 deg C (32 deg F) and 3 km (2 mi) when below 0 deg C (32 deg F). The strategy changes were implemented to improve vacuum supply management and axle warm up in cold temperatures. The engine must run for a minimum of 5 minutes to build sufficient vacuum before performing any vacuum related testing. Refer to the Workshop Manual (WSM) Section, 307-08A > Four-Wheel Drive Systems > System Operation and Component Description for additional information.
SSM 492172020-10-06. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; ELECTRICAL SYSTEM:ADAS:BLINDSPOT:SOFTWARE. Some 2015-2020 F-150/Mustang, 2016-2020 Edge, 2016-2018 MKX and 2019-2020 Nautilus vehicles built on or before 18-Jan-2020 may exhibit a mirror click and/or ratcheting noise when using memory functions or easy entry/exit function. This may be due to the software in the driver door module (DDM) and passenger door module (PDM). To correct the condition, reprogram the DDM and PDM with the latest software level of the appropriate Ford diagnostic scan tool. For claiming use causal part 14B291 and applicable labor times in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 492102020-10-06. Service bulletin. ENGINE AND ENGINE COOLING. Some 2009-2020 Ford and Lincoln vehicles equipped with turbochargers may exhibit an oil leak from the turbocharger oil supply or return tubes, O-rings or 6.7L pedestal gasket. Although oil may collect on the turbocharger, it is very rare for a turbocharger to leak oil. To isolate the source of the leak, refer to Workshop Manual (WSM), Section 303-00 General Information > Diagnosis and Testing > Engine > Engine Oil Leaks - Fluorescent Oil Additive Method procedure. When an oil leak is present at a turbocharger oil supply or drain tube, remove the affected oil tube and inspect for damage, and replace the O-ring seals, pedestal gasket or oil tube as required. Refer to WSM, Section 303-04. For claiming, use the affected oil tube or pedestal gasket as the causal part and applicable labor operations in Sections 6 and 9 of the Service Labor Time Standards (SLTS) Manual.
SSM 492032020-10-06. Service bulletin. ENGINE AND ENGINE COOLING. Some 2017-2020 F-150 vehicles equipped with a 3.5L EcoBoost engine, 2018-2020 F-150 vehicles equipped with a 2.7L EcoBoost or 5.0L engine, 2019-2020 F-150 vehicles equipped with a 3.0L engine, may exhibit a high pitched squeal or whistle type noise from the engine compartment after the engine is shut off. This condition may be due to the air conditioning (A/C) low side system pressure exceeding the high side pressure resulting in equalization of A/C system pressures through the A/C compressor. This noise is not detrimental to system operation or durability. Submit a Global Concern Report, and let the customer know they can continue to drive the vehicle. Set a follow-up appointment for June 2021 when repairs are expected to become available. Follow up with the customer to confirm the appointment once OASIS is updated.
TSB 20-23152020-10-02. Service bulletin. ENGINE AND ENGINE COOLING. Some 2017-2020 F-150 2018-2020 Expedition/Navigator vehicles built on or before 31-Oct-2019 and equipped with a 3.5L EcoBoost engine may exhibit a ticking/tapping or rattle type noise from the top front cover area of the engine on initial start-up after a cold soak of 6 hours or more that may last for 2-5 seconds. This may be due to a worn variable cam timing (VCT) unit. To correct the condition, follow the Service Procedure steps to replace the VCT units and update the powertrain control module (PCM) calibration with revised VCT parameters.
20B21-S12020-10-01. Service bulletin. ENGINE AND ENGINE COOLING. Certain 2020 Model Year Transit vehicles with 3.5L engines and F-150 / Police Interceptor Utility vehicles with 3.3L engines - Cylinder Head Replacement
TSB 20-23012020-10-01. Service bulletin. ELECTRICAL SYSTEM; ELECTRICAL SYSTEM:SOFTWARE; BACK OVER PREVENTION: CAMERA SYSTEM. Some 2019 MKZ, 2019-2020 Mustang/Continental/Fusion/F-150/Transit Connect/ Ranger/Edge/Nautilus and 2020 Escape/Corsair/Aviator/Explorer/Expedition/ Navigator/F-Super Duty vehicles with SYNC 3 may experience various SYNC performance related concerns. To correct the condition, follow the Service Procedure.
TSB 20-22672020-10-01. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; ELECTRICAL SYSTEM:ADAS:DRIVER MONITORING:CAMERA/SENSOR. Some 2015-2020 F-150 except Raptor, 2017-2020 F-Super Duty, 2018-2020 Expedition vehicles equipped with a front camera washer may exhibit a washer fluid leak at the front camera washer jet when not in use. This may be due to the rubber seal internal to the jet. To correct the condition, follow the Service Procedure to replace the washer jet.
SSM 490822020-09-04. Service bulletin. POWER TRAIN; ELECTRICAL SYSTEM. Some 2019-2020 F-150 vehicles equipped with a 5.0L engine may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P0011, P0012, P0021 and/or P0022 stored in the powertrain control module (PCM). In addition to the DTCs, the vehicle may also exhibit noise near the front of the valve covers from the intake variable camshaft timing (VCT) phasers. To resolve this condition, replace only the VCT solenoid(s) associated with the DTCs present. If the condition persists after VCT solenoid replacement, continue with normal Powertrain Controls and Emissions Diagnosis (PC/ED) Manual diagnostics for any DTCs, and/or follow engine NVH diagnostics in Workshop Manual (WSM), Section 303-00. For claiming, use causal part 6M280 and applicable labor operations in the Service Labor Time Standards (SLTS) Manual.
SSM 490652020-09-04. Service bulletin. ENGINE AND ENGINE COOLING; ELECTRICAL SYSTEM; FUEL SYSTEM, DIESEL. Some 2011-2020 F-Super Duty, 2015-2019 Transit, 2016-2021 F-650/F-750 and 2018-2020 F-150 vehicles equipped with a 6.7L, 3.2L or 3.0L engine may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P207F, P20EE, P229F, P2201 and/or P24AE. This may be a result of using aftermarket cleaning liquids or tools for the exhaust gas recirculation (EGR) cooler or intake. Ford does not recommend the cleaning of diesel intakes or EGR coolers using any aftermarket tool that injects a cleaning foam or liquid substance into the EGR cooler or intake. Using these types of fluids can result in sodium poisoning of the NOx and particulate matter (PM) sensors resulting in degraded operation and permanent damage to the after treatment system. Use of these cleaning tools may void the emissions warranty of the hot end after treatment exhaust system and the attached emissions sensors.
SSM 490502020-09-04. Service bulletin. POWER TRAIN. Some 2018-2020 F-150 vehicles equipped with a 5.0L engine may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P0171, P0172, P0174 and/or P0175. This may be due to incorrect flex fuel learning, which is often caused by customer refueling habits when adding only small amounts of fuel, the vehicle mislearning of inferred ethanol fuel mixture (FF_INF value) or a component concern. Refer to pinpoint test H in the Powertrain Control/Emissions Diagnosis (PC/ED) Manual for diagnostics and Flex Fuel GSB for additional flex fuel system information and diagnostic tips.
SSM 491222020-09-02. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:OIL/LUBRICATION; EQUIPMENT. Some 2015-2020 F-150, 2016-2018 MKX, 2019-2020 Nautilus, 2015-2020 Edge, 2017-2019 Fusion, 2017-2020 MKZ And 2017-2020 Continental vehicles equipped with a 2.7L/3.0L EcoBoost engine may appear to have a low engine oil level if the proper procedures are not followed. Refer to the Owner's Manual > Maintenance > Engine oil check section. When checking the engine oil level after shutting off the engine wait at least 15 minutes prior to checking in order to allow the oil to drain back to the oil pan. The engine oil level can be checked immediately if the engine has not been started. When changing the engine oil the engine needs to be at normal operating temperature and the oil filter removed before draining the oil. Allow the oil pan to drain completely for up to 5 minutes. Check oil level after filling by following the oil level check procedure.
TSB 20-22942020-09-02. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). This article supersedes TSB 20-2162 to update the Labor Operations descriptions. Some 2018-2020 F-150 Raptor and 2019-2020 F-150 Limited vehicles equipped with a 3.5L EcoBoost High-Output engine may exhibit excessive oil consumption with no visible oil leaks with or without diagnostic trouble code (DTC) P0365 and/or P0369. To correct the condition, follow the Service Procedure steps to reprogram the powertrain control module (PCM), and for vehicles built on or before 1-Apr-2019 that have not previously had both valve covers replaced perform an oil consumption test.
TSB 20-22922020-09-02. Service bulletin. ENGINE AND ENGINE COOLING. Some 2019-2020 F-150 vehicles equipped with a 3.3L Duratec engine and built on or before 18-Aug-2020 may exhibit a lack of heat intermittently. This may be due to the powertrain control module (PCM) not running the auxiliary coolant pump during stop-start situations. To correct the condition, follow the Service Procedure to reprogram the PCM.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.