WenmarOpen by Wenmar Pro

Service bulletins for the 2018 Ford F-150

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

418 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

Only bulletins with component: Engine are shown. Show all

Bulletins, newest first
TSB 18-23262018-11-19. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:DIESEL; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Some 2018 F-150 vehicles equipped with a 3.0L diesel engine built on or before 10-Oct-2018 may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P06EA, P0315a, P20EE, P0401, P2201, P0106, P0191 and/or P061A stored in the powertrain control module (PCM). Follow the Service Procedure steps to correct the condition.
SSM 475032018-09-24. Service bulletin. ENGINE AND ENGINE COOLING. Some 2017-2018 Vehicles equipped with a 3.3L or 3.5L EcoBoost engine may exhibit a no crank no start condition that only occurs in freezing ambient temperatures. This may be due to a frozen starter. Replace the starter with part number Jl3Z-11002-E. For claiming, use causal part 11002 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 474462018-09-24. Service bulletin. ENGINE AND ENGINE COOLING. Some Ford and Lincoln vehicles equipped with a 2.7L or 3.0L EcoBoost engine may exhibit an oil leak from the engine oil pan RTV seal. Replace the oil pan following the procedure in Workshop Manual (WSM) Section, 303-01. After removing the oil pan it is suggested to allow the crankcase to drain overnight to minimize the chance of residual oil contaminating the crankcase sealing rail. Remove all traces of old RTV and clean the engine sealing surface using only Motorcraftù Metal Brake Parts Cleaner, then wipe with Motorcraftù Metal Surface Prep Wipes and allow to air dry. Refer to WSM, Section 303-00 > RTV Sealing Surface Cleaning and Preparation. If possible, allow the new RTV sealant to cure for 4 hours before refilling the engine with oil. Skipping or improperly completing steps may result in repeat oil pan leaks.
SSM 474412018-09-24. Service bulletin. ENGINE AND ENGINE COOLING. Some 2018 F-150 vehicles equipped with a 5.0L engine may exhibit an illuminated MIL with DTCs P0390 and/or P0394. These DTCs may be caused by low engine oil level. Before performing any diagnosis or repair, make sure the oil level is between the minimum and maximum marks on the oil level indicator. If the oil level is below the minimum mark, diagnose the low oil level concern first. Refer to the Workshop Manual, Section 303-00. If the oil level is in the normal operating range, inspect C1627. If no concerns are present, replace the bank 2 (LH) exhaust variable camshaft timing (VCT) solenoid. Do not replace camshaft position sensors for these DTCs. For claiming, use causal part 6M280 and applicable labor operations in Section 06 of the Service Labor Time Standards (SLTS) Manual. Engineering is investigating, monitor OASIS for updates.
TSB 18-22642018-09-24. Service bulletin. ENGINE. Some 2018 F-Super Duty vehicles equipped with a 6.7L diesel engine may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P00BD, P012F, P0181, P0474, P124C, P1247, P20EE, P205B, P2263, P2269, and/or P2459. Follow the Service Procedure steps to correct the condition.
TSB 18-22492018-09-24. Service bulletin. ENGINE. Some 2018 F-150 vehicles equipped with a 2.7L EcoBoost and built on or before 27-Nov-2017 may exhibit an intermittent engine stall when coming to a stop while towing. Follow the Service Procedure steps to correct the condition.
TSB 18-22442018-09-24. Service bulletin. ENGINE AND ENGINE COOLING. Some 2015-2018 F-150 vehicles equipped with a 3.3L, 3.5L Duratec, 3.5L EcoBoost and 5.0L engine without a block heater may exhibit a lack of heat concern from the heating ventilation and air conditioning (HVAC) system when operating the vehicle in temperatures consistently below -20 degrees C (4 degrees F). This condition may be due to deposits from the engine coolant becoming trapped in the heater core. Follow the Service Procedure steps to correct the condition.
SSM 474062018-09-10. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; ENGINE. Some 2017-2018 F-150 and 2018 Navigator vehicles equipped with a 3.5L EcoBoost and built on or before 09-Mar-2018 may exhibit excessive oil consumption. If there are no visible external oil leaks, replace both engine valve covers. Refer to Workshop Manual, Section 303-01. For claiming, use causal part 6582 and applicable labor operations in Section 6 of the Service Labor Time Standards (SLTS) Manual.
SSM 473942018-07-23. Service bulletin. EQUIPMENT; ENGINE AND ENGINE COOLING. Some 2013-2018 F-150, 2015-2018 Transit/Expedition, and 2015-2017 Navigator vehicles equipped with a 3.5L EcoBoost engine with greater than 20,000 miles may exhibit a tick type noise from the cylinder block area. This noise may be caused by a cracked piston skirt. The noise can be isolated to a cylinder using a stethoscope or other suitable listening device. Canceling the affected cylinder will reduce or eliminate the noise. If the noise is isolated to a specific cylinder, it is recommended to replace the short block. If the noise cannot be isolated using the methods described, refer to the Workshop Manual (WSM) for diagnosis. A cracked piston skirt does not result in metal contamination of the engine or any related cylinder head damage. Prior approval for short block replacement is not required under new vehicle limited warranty coverage.
SSM 473772018-07-23. Service bulletin. ENGINE; EQUIPMENT. Some 2017-2018 F-150 vehicles equipped with a 3.5L EcoBoost engine built at Kansas City Assembly Plant on or before 23-Feb-2018 or Dearborn Truck Plant on or before 26-Feb-2018 may exhibit an oil leak from the oil pan RTV seal. Replace the oil pan following the procedure in Workshop Manual (WSM) Section, 303-01. After removing the oil pan, it is suggested to allow the crankcase to drain overnight to minimize the chance of contaminating the sealing rail. Prepare the engine sealing surface following the procedure in WSM Section, 303-00. Proper usage of the Motorcraftù Metal Surface Prep Wipes is critical. If possible, allow the new RTV sealant to cure for 4 hours before refilling the engine with oil. Correctly following the WSM procedures is critical. Skipping or improperly completing steps may result in repeat oil pan leaks.
SSM 473762018-07-23. Service bulletin. ENGINE; EQUIPMENT. Some 2013-2018 F-150, 2015-2018 Transit/Expedition, and 2015-2017 Navigator vehicles equipped with a 3.5L EcoBoost engine with greater than 20,000 miles may exhibit a tick type noise from the cylinder block area. This noise may be caused by a cracked piston skirt. The noise can be isolated to a cylinder using a stethoscope or other suitable listening device. Canceling the affected cylinder will reduce or eliminate the noise. If the noise is isolated to a specific cylinder, it is recommended to replace the short block. If the noise cannot be isolated using the methods described, refer to the Workshop Manual (WSM) for diagnosis. A cracked piston skirt does not result in metal contamination of the engine or any related cylinder head damage. Short block replacement does not require prior approval.
SSM 473652018-07-23. Service bulletin. EQUIPMENT; ENGINE. Some 2018 F150, Navigator and Expedition vehicles equipped with 3.5L EcoBoost engine may experience malfunction indicator lamp (MIL) illumination with Diagnostic Trouble Code(s) DTC P0365 and/or P0369. This may be due to low engine oil level, low engine oil pressure or damaged variable camshaft timing (VCT) phasers. Before performing Powertrain Control and Emissions Diagnostics (PC/ED) Manual diagnostics, inspect the engine oil level and evaluate any abnormal VCT noise conditions. If engine oil level is correct, and no unusual engine noises are present, proceed with normal PC/ED diagnostics test PPT 'DR'.
SSM 473632018-07-23. Service bulletin. EQUIPMENT; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); ENGINE AND ENGINE COOLING:ENGINE:DIESEL. Some 2018 F-150 vehicles equipped with a 3.0L diesel engine may have DTC P061B set in the powertrain control module (PCM) after scan tool requested engine speed control. This may include engine speed output state control in data logger, key on engine running (KOER) self-test, or a manual diesel particulate filter (DPF) regeneration where engine speed is increased during the regeneration. Disregard this DTC. Engineering is aware of this concern. Monitor OASIS for updates.
SSM 473372018-07-23. Service bulletin. ELECTRICAL SYSTEM; ENGINE. Some 2018 F-150 vehicles equipped with a 3.3L engine built on or before 7-May-2018 at Dearborn Assembly Plant or on or before 31-May-2018 at Kansas City Assembly Plant may exhibit an illuminated MIL and/or runs rough condition with DTC P0192 and/or P0193. Various other DTCs may be set. This may be due to engine harness chaffing at the right cylinder head near connector C1056 at the cylinder head core plug boss. The connector will need to be removed from the retainer to inspect the back side of the harness for any damage. Repair as necessary. Make sure to wrap the exposed wiring with Rotunda Coroplast Electrical Wire Harness Tape (RTTP part number NAI837X or equivalent) and reposition the harness to prevent future chaffing concerns. For claiming, use causal part 12A581 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 472652018-05-21. Service bulletin. ENGINE AND ENGINE COOLING. Some Ford and Lincoln vehicles equipped with a 2.7L or 3.0L EcoBoost engines may exhibit an oil leak from the engine oil pan RTV seal. Replace the oil pan by performing the published Workshop Manual (WSM) service procedures. After removing the oil pan, it is suggested to allow the crankcase to drain overnight to minimize the chance of residual oil contaminating the crankcase sealing rail. Remove all traces of old RTV, clean the engine sealing surface with only Motorcraftù Metal Brake Parts Cleaner then wipe with Motorcraftù Metal Surface Prep Wipes, and allow to air dry as directed in WSM, Section 303-00, RTV Sealing Surface Cleaning and Preparation. If possible, after the new oil pan is installed, allow the new RTV sealant to cure for 4 hours before refilling the engine with oil. Ford is investigating this concern. Monitor OASIS for future updates.
SSM 469062018-01-29. Service bulletin. ENGINE AND ENGINE COOLING; ELECTRICAL SYSTEM. Some 2015-2018 F150/Edge, 2016-2018 MKX and 2017-2018 Fusion, Continental vehicles equipped with a 2.7L engine may experience a malfunction indicator lamp (MIL) and/or wrench lamp with Diagnostic Trouble Codes (DTCs): P0116, P0117, P0118, P0119, P0217, P0330, P1026, and/or P130D. This may be due to a engine coolant temperature (ECT) sensor connector which is not fully seated or damaged wiring between connectors C1064 and C1047 for F150 and C1016 and C1168 for Edge/MKX/Fusion/Continental vehicles. ECT sensors should not be replaced if damaged wiring is found at or near these connectors. If an issue with the wiring is found use causal part 12A699.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.