WenmarOpen by Wenmar Pro

Service bulletins for the 2017 Ford F-150

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

343 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Bulletins, newest first
20M042021-08-02. Service bulletin. LATCHES/LOCKS/LINKAGES. On your vehicle, moisture and water entering a power door lock actuator housing could cause the actuator motor to momentarily freeze in cold temperatures and may also cause actuator motor corrosion over time. Frozen water within a power door lock actuator housing or corrosion of the power door lock actuator motor could result in an inoperative power door lock function on the affected door.
TSB 21-20842021-08-02. Service bulletin. POWER TRAIN. Some 2017-2021 F-150 vehicles equipped with a 2.7L EcoBoost engine may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P0096 in the powertrain control module (PCM). This may be due to an issue with the manifold absolute pressure (MAP) sensor. To correct the condition, follow the Service Procedure to replace the MAP sensor.
TSB 21-21992021-07-01. Service bulletin. EQUIPMENT. This article supersedes TSB 21-2144 to update the vehicle model years affected and the Part List. Some 2015-2020 F-150 and 2017-2021 F-Super Duty vehicles may exhibit a lack of heat or cooling from the cabin vents when the climate control settings are adjusted between hot and cold. This may be due to a stuck/binding temperature door within the climate control housing or binding/inoperative temperature door actuator. Diagnostic trouble code (DTC) B1081:07 may be present in the front controls interface module (FCIM). To correct the condition, follow the Service Procedure steps to remove the climate control housing and replace the temperature door actuator(s) and/or lubricate the temperature blend door bearing surface.
21M042021-07-01. Service bulletin. LATCHES/LOCKS/LINKAGES. In some of the affected vehicles, moisture and water entering a power door lock actuator housing can cause the actuator motor to momentarily freeze in cold temperatures and may also cause actuator motor corrosion over time. Frozen water within a power door lock actuator housing or corrosion of the power door lock actuator motor could result in an inoperative power door lock function on the affected door.
TSB 21-21752021-07-01. Service bulletin. ELECTRICAL SYSTEM. Some 2016 MKS, 2016-2017 Navigator, 2016-2018 F-150/Focus/C-MAX/Edge/Fiesta/MKX/Transit Connect/Mustang, 2017-2018 Continental/Fusion/MKZ, 2017-2019 Explorer, 2016-2019 Escape/MKC/Flex/MKT/Taurus/Transit/Expedition/F-Super Duty, and 2018-2019 EcoSport vehicles equipped with SYNC 3 may experience various SYNC performance related concerns.
TSB 20-22682021-06-03. Service bulletin. EQUIPMENT. Some 2015-2020 F-150 XL/XLT vehicles may exhibit warping/separation of the instrument panel at the defrost vents. To correct the condition, follow the Service Procedure to replace the instrument panel upper section.
TSB 21-21442021-06-03. Service bulletin. EQUIPMENT. Some 2015-2021 F-150 and 2017-2021 F-Super Duty vehicles may exhibit a lack of heat or cooling from the cabin vents when the climate control settings are adjusted between hot and cold. This may be due to a stuck/binding temperature door within the climate control housing or binding/inoperative temperature door actuator. Diagnostic trouble code (DTC) B1081:07 may be present in the front controls interface module (FCIM). To correct the condition, follow the Service Procedure steps to remove the climate control housing and replace the temperature door actuator(s) and/or lubricate the temperature blend door bearing surface.
SSM 498212021-06-01. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION; ENGINE AND ENGINE COOLING. Some 2015-2021 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTC) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK11 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 498202021-06-01. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM. Some 2017-2021 Ford and Lincoln vehicle owners may experience a condition of missing Authorization, Command and Control, Battery Charging Details or Phone-as-a-Key setup buttons/selections in their FordPass or LincolnWay App. This condition is due to an error within the FordPass or LincolnWay App and not due to a concern on the vehicle. Verify that the customers FordPass or LincolnWay App is at the latest version. Replacement or reprogramming of the telematics control unit (TCU)/gateway module (GWM)/remote function actuator (RFA) will not resolve this condition. If the condition persists, Utilize the FordPass Guides or Lincoln Way Concierge teams.
21B10-S12021-05-04. Service bulletin. POWER TRAIN. Certain 2017-2020 Model Year F-150 Equipped with a 3.5L GTDI Engine Powertrain Control Module Reprogram for Cam Phaser Rattle Reports of Transmission Shudder after PCM Reprogram: Dealers are instructed to stop performing this field service action until further notice. This shudder is under investigation.
TSB 21-21192021-05-04. Service bulletin. ENGINE AND ENGINE COOLING. Some 2017-2020 F-150 2018-2020 Expedition/Navigator vehicles built on or before 31-Oct-2019 and equipped with a 3.5L EcoBoost engine may exhibit a ticking/tapping or rattle type noise from the top front cover area of the engine on initial start-up after a cold soak of 6 hours or more that may last for 2-5 seconds. This may be due to a worn variable cam timing (VCT) unit. To correct the condition, follow the Service Procedure steps to replace the VCT units.
SSM 497612021-05-03. Service bulletin. ENGINE AND ENGINE COOLING. Some 2011-2021 Mustang and F-150 vehicles equipped with a 5.0L engine may exhibit a ticking noise at idle after an engine oil change. It is often referred to as typewriter noise because of its similarity to the sound of a mechanical typewriter. The noise in question may be heard on some engines when engine temperatures reach 150F (65Å’C) or higher and engine speed is at idle up to approximately 1700 RPMs. It can typically be heard at the front wheel well and is often isolated to the transmission bell housing or oil pan area. The typewriter noise is not detrimental to the engine function or durability and has no short or long term effects on the engine. This an operating characteristic of the 5.0L engine and no repairs should be attempted.
TSB 21-20762021-04-03. Service bulletin. POWER TRAIN. Some 2013-2018 F-150 vehicles equipped with electronic shift on-the-fly (ESOF) 4-wheel drive (4WD) may exhibit an intermittent grinding noise while driving in 2-wheel drive (2WD) mode most commonly on acceleration. ESOF can be identified as it does not have a 4WD AUTO (4A) position on the mode selector switch (MSS). This may be due to a loss of vacuum to the integrated wheel end (IWE) actuators and/or wear of the IWE components. To correct the condition, follow the Service Procedure steps to reprogram the transfer case control module (TCCM) and replace any worn vacuum and/or IWE components.
21B102021-04-03. Service bulletin. ENGINE AND ENGINE COOLING. Certain 2017-2020 Model Year F-150 Equipped with a 3.5L GTDI Engine Powertrain Control Module Reprogram for Cam Phaser Rattle In some of the affected vehicles, an undesirable noise may develop from the cam phasers in the 3.5L GTDI engine. This noise might occur as a rattle when starting the engine after the vehicle was turned off for an extended period of time, or as a knocking noise when the engine is idling after it is warmed up. A cam phaser that has developed an undesirable noise does not affect the vehicle safety, performance, or emissions
21N032021-04-03. Service bulletin. ENGINE AND ENGINE COOLING. Certain 2017-2020 Model Year F-150 Equipped with a 3.5L GTDI Engine Cam Phaser Replacement In some of the affected vehicles, an undesirable noise may develop from the cam phasers in the 3.5L GTDI engine. This noise might occur as a rattle when starting the engine after the vehicle was turned off for an extended period of time or as a knocking noise when the engine is idling after it is warmed up. A cam phaser that has developed an undesirable noise does not affect the vehicle safety, performance, or emissions
SSM 494772021-02-04. Service bulletin. EQUIPMENT. Some 2015-2021 F-150, 2016-2018 MKX, 2019-2021 Nautilus, 2015-2021 Edge, 2017-2019 Fusion, 2017-2020 MKZ And 2017-2020 Continental vehicles equipped with a 2.7L/3.0L EcoBoost engine may appear to have a low engine oil level if the proper procedures are not followed. Refer to the Owner's Manual > Maintenance > Engine oil check section. When checking the engine oil level after shutting off the engine wait at least 15 minutes prior to checking in order to allow the oil to drain back to the oil pan. The engine oil level can be checked immediately if the engine has not been started. When changing the engine oil the engine needs to be at normal operating temperature and the oil filter removed before draining the oil. Allow the oil pan to drain completely for up to 5 minutes. Check oil level after filling by following the oil level check procedure.
SSM 493182020-12-04. Service bulletin. EQUIPMENT. For 2011-2020 F-150/Mustang vehicles equipped with a 5.0L engine when installing a replacement secondary timing chain tensioner (6K254) or secondary timing chain guide (6K297), it is necessary to replace both components as a pair, using the latest level parts. Make sure to use secondary timing chain tensioner part number ML3Z-6K254-A and secondary timing chain guide part number ML3Z-6K297-A.
SSM 493552020-12-04. Service bulletin. EQUIPMENT; ENGINE AND ENGINE COOLING. Some 2015-2020 F-150 and 2018-2020 Expedition/Navigator vehicles equipped with a 3.5L/2.7L EcoBoost engine and four-wheel drive (4WD) may exhibit an intermittent grinding type noise while driving in two-wheel drive (2WD), most commonly on acceleration. This noise could appear to be turbocharger related. After engineering analysis of returned turbochargers that have been replaced for this condition, no concerns were identified with the turbochargers. The grinding type noise may be related to the 4WD system integrated wheel ends (IWE). To aid in diagnosis, shift the vehicle to 4WD and attempt to verify the condition. If the grinding noise no longer occurs with the vehicle in 4WD a IWE vacuum system and/or mechanical fault may be present.
TSB 20-23072020-11-05. Service bulletin. ELECTRICAL SYSTEM; WHEELS; EQUIPMENT. Some 2003-2020 Expedition/Navigator and 2006-2020 F-150 vehicles equipped with TOD transfer cases may exhibit grinding/clicking/ratcheting noise from the front wheel area. This may be due to partial engagement of the integrated wheel ends (IWE). To correct this condition, follow the Service Procedure steps to remove and cap the vacuum supply line.
TSB 20-23062020-11-05. Service bulletin. ENGINE AND ENGINE COOLING; POWER TRAIN:AUTOMATIC TRANSMISSION:COOLING UNIT AND LINES; EQUIPMENT. The service part long block for 2017-2018 F-150 vehicles equipped with a 3.5L EcoBoost engine built at Kansas City Assembly Plant on or before 23-Feb-2018 or Dearborn Truck Plant on or before 26-Feb-2018 and 2018 Expedition/Navigator vehicles built on or before 19-Mar-2018 has been changed to a one piece oil pan design. To make sure there is proper fitment of the new long block with the one piece oil pan, replacement of the transmission cooler coolant lines and an engine harness modification will be necessary. To correctly install, follow the Service Procedure steps to complete the repair.
TSB 20-22782020-11-05. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; EQUIPMENT; POWER TRAIN. Some 2013-2018 F-150 vehicles equipped with Electronic Shift On-The-Fly (ESOF) 4-wheel drive (4WD) may exhibit an intermittent grinding noise while driving in 2-wheel drive (2WD) mode most commonly on acceleration. This may be due to a loss of vacuum to the integrated wheel end (IWE) actuators and/or wear of the IWE components. To correct the condition, follow the Service Procedure steps to reprogram the transfer case control module (TCCM) and replace any worn vacuum and/or IWE components.
SSM 492212020-10-06. Service bulletin. EQUIPMENT; EQUIPMENT ADAPTIVE/MOBILITY; ENGINE AND ENGINE COOLING. When installing a replacement short block in 2015-2017 vehicles equipped with a 2.7L or 3.0L EcoBoost engine, the engine must be converted to use a belt driven oil pump with the following parts: left exhaust camshaft JT4Z-6250-B, left intake camshaft - JT4Z-6250-A, belt driven oil pump - KT4Z-6600-A, oil pump belt - JT4Z-6B651-A, crankshaft sprockets - FT4Z-6306-A (x2), crankshaft oil pump belt drive - JT4Z-6306-A. Follow the engine assembly procedure in Workshop Manual (WSM), Section 303-01 using these new parts without installing the chain tensioner or guides as they are not needed with the belt driven oil pump. Fill out the Authorized Modification Label (FPS-8262) with the following text: 'Engine has been modified to use a belt-driven oil pump per SSM XXXXX' and attach it to the underside of the hood.
SSM 492172020-10-06. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; ELECTRICAL SYSTEM:ADAS:BLINDSPOT:SOFTWARE. Some 2015-2020 F-150/Mustang, 2016-2020 Edge, 2016-2018 MKX and 2019-2020 Nautilus vehicles built on or before 18-Jan-2020 may exhibit a mirror click and/or ratcheting noise when using memory functions or easy entry/exit function. This may be due to the software in the driver door module (DDM) and passenger door module (PDM). To correct the condition, reprogram the DDM and PDM with the latest software level of the appropriate Ford diagnostic scan tool. For claiming use causal part 14B291 and applicable labor times in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 492102020-10-06. Service bulletin. ENGINE AND ENGINE COOLING. Some 2009-2020 Ford and Lincoln vehicles equipped with turbochargers may exhibit an oil leak from the turbocharger oil supply or return tubes, O-rings or 6.7L pedestal gasket. Although oil may collect on the turbocharger, it is very rare for a turbocharger to leak oil. To isolate the source of the leak, refer to Workshop Manual (WSM), Section 303-00 General Information > Diagnosis and Testing > Engine > Engine Oil Leaks - Fluorescent Oil Additive Method procedure. When an oil leak is present at a turbocharger oil supply or drain tube, remove the affected oil tube and inspect for damage, and replace the O-ring seals, pedestal gasket or oil tube as required. Refer to WSM, Section 303-04. For claiming, use the affected oil tube or pedestal gasket as the causal part and applicable labor operations in Sections 6 and 9 of the Service Labor Time Standards (SLTS) Manual.
SSM 492032020-10-06. Service bulletin. ENGINE AND ENGINE COOLING. Some 2017-2020 F-150 vehicles equipped with a 3.5L EcoBoost engine, 2018-2020 F-150 vehicles equipped with a 2.7L EcoBoost or 5.0L engine, 2019-2020 F-150 vehicles equipped with a 3.0L engine, may exhibit a high pitched squeal or whistle type noise from the engine compartment after the engine is shut off. This condition may be due to the air conditioning (A/C) low side system pressure exceeding the high side pressure resulting in equalization of A/C system pressures through the A/C compressor. This noise is not detrimental to system operation or durability. Submit a Global Concern Report, and let the customer know they can continue to drive the vehicle. Set a follow-up appointment for June 2021 when repairs are expected to become available. Follow up with the customer to confirm the appointment once OASIS is updated.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.