WenmarOpen by Wenmar Pro

Service bulletins for the 2015 Ford F-150

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

249 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

Only bulletins with component: Brakes are shown. Show all

Bulletins, newest first
SSM 512612023-01-06. Service bulletin. SERVICE BRAKES. Some Ford and Lincoln vehicles may exhibit noise when the brakes are applied. When diagnosing and repairing brake noise conditions, use the Workshop Manual (WSM) and the appropriate pinpoint test in section 206-00. The brake rotors should only be machined if directed by the WSM because one or more of the following conditions are present on the braking surface: scoring, excessive corrosion/rust or pitting, bluing/discoloration and/or heat spots. For additional information, refer to WSM section 206-00.
SSM 511202022-10-11. Service bulletin. SERVICE BRAKES, HYDRAULIC. Some Ford and Lincoln vehicles may exhibit noise when the brakes are applied. When diagnosing and repairing brake noise conditions, use the Workshop Manual (WSM) and the appropriate pinpoint test in section 206-00. The brake rotors should only be machined if directed by the WSM because one or more of the following conditions are present on the braking surface: scoring, excessive corrosion/rust or pitting, bluing/discoloration and/or heat spots. For additional information, refer to WSM section 206-00.
SSM 500642021-09-04. Service bulletin. SERVICE BRAKES, ELECTRIC:SOFTWARE/PROGRAMMING. Some 2013-2021 Ford and Lincoln vehicles may exhibit noise when the brakes are applied. When diagnosing and repairing brake noise conditions, use the Workshop Manual (WSM) and the appropriate pinpoint test in section 206-00. The brake rotors should only be machined if directed by the WSM because one or more of the following conditions are present on the braking surface: scoring, excessive corrosion/rust or pitting, bluing/discoloration and/or heat spots. For additional information, refer to WSM section 206-00.
TSB-20-20282020-03-03. Service bulletin. SERVICE BRAKES, HYDRAULIC:POWER ASSIST:VACUUM; EQUIPMENT. Some 2013-2018 F-150/Expedition/Navigator vehicles equipped with 4-wheel drive (4WD) may exhibit an intermittent grinding noise while driving in 2-wheel drive (2WD) mode most commonly on acceleration. This may be due to a loss of vacuum to the integrated wheel end (IWE) actuators and/or wear of the IWE components. To correct the condition, follow the Service Procedure steps to reprogram the transfer case control module (TCCM) and replace any worn vacuum and/or IWE components.
SSM 461392017-02-08. Service bulletin. SERVICE BRAKES. SOME 2015-2016 F-150 VEHICLES MAY EXPERIENCE INTERMITTENT LOSS OF THROTTLE PEDAL RESPONSE, ILLUMINATED WRENCH, HILL DESCENT, AIRBAG, ANTI LOCK BRAKE SYSTEM(ABS) AND/OR ADVANCED TRAC WARNING INDICATORS AND/OR P2122, P2123, P2124, P2125, P2127, P2128 AND/OR P2138 DTCS. THIS MAY BE CAUSED BY THE ACCELERATOR PEDAL POSITION (APP) SENSOR 14A005 HARNESS BEING IMPROPERLY ROUTED BEHIND THE BRAKE BOOSTER TO BRAKE PEDAL BRACKET. IF THE HARNESS IS IMPROPERLY ROUTED, LOOSEN THE BRACKET TO FREE THE HARNESS. INSPECT AND REPAIR DAMAGED CIRCUITS BEFORE PROPERLY ROUTING THE HARNESS. IF THE HARNESS IS PROPERLY ROUTED, PROCEED WITH NORMAL DIAGNOSTICS IN THE WORKSHOP MANUAL (WSM).

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.