Service bulletins for the 2024 Ford Explorer
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
106 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
| SSM 52917 | 2024-09-24. Service bulletin. UNKNOWN OR OTHER. Some 2020-2024 Explorer/Aviator/Police Interceptor Utility vehicles may exhibit erratic shifting and/or a transmission fluid venting condition. |
|---|---|
| SSM 52896 | 2024-09-24. Service bulletin. EXTERIOR LIGHTING. Some 2023-2025 Explorer/Aviator vehicles equipped with the 3.0L EcoBoost engine and up to 15,000 miles (24,140 km) may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P219A (Bank 1 Air-Fuel Ratio Imbalance) and/or P219B (Bank 2 Air-Fuel Ratio Imbalance) stored in the powertrain control module (PCM) with no effect on vehicle operation. |
| SSM 52832 | 2024-09-04. Service bulletin. UNKNOWN OR OTHER. Some 2024-2025 Explorer/Aviator/Police Interceptor Utility vehicles may exhibit an illuminated malfunction indicator (MIL) lamp with engine over-temperature warning in the message center and poor air conditioning (A/C) performance from the engine cooling fan not running. |
| SSM 52820 | 2024-09-04. Service bulletin. UNKNOWN OR OTHER. Some 2019-2024 Ford and Lincoln vehicles equipped with a telematics control unit module (TCU) may exhibit the Location toggle button in the Connectivity setting menu grayed out with an inability to switch it off. |
| SSM 52776 | 2024-08-16. Service bulletin. SEATS. Some 2020-2025 Explorer/Aviator vehicles may have a concern where the second row outboard manual/power seats do not fold, exhibit excess effort to fold, or do not slide forward/backward easily. Power or manual second row seats must be pushed forward manually during easy entry function since the assist spring will reduce but not eliminate manual effort. Refer to the Owner's Manua |
| SSM 52774 | 2024-08-16. Service bulletin. UNKNOWN OR OTHER. Some 2020-2024 Escape/Explorer, 2021-2024 F-150, 2022-2024 Maverick and 2024 Nautilus vehicles equipped with a full hybrid electric vehicle (FHEV) powertrain may exhibit a cable connection error screen from the Midtronics xRC-3363 High Voltage Battery Rescue Charger. The xRC-3363 will prompt the technician to verify the low voltage connections when no actual fault is present. This may be due to the software level of the Midtronics xRC-3363 High Voltage Battery Rescue Charger. |
| SSM 52773 | 2024-08-16. Service bulletin. UNKNOWN OR OTHER. 2023-2024 F-150/Escape/Explorer/Maverick and 2024 Nautilus vehicles equipped with a full hybrid electric vehicle (FHEV) powertrain may exhibit diagnostic trouble codes (DTCs) P0A7D and/or P0DE6 and the vehicle identification number (VIN) is not recognized by the Midtronics xRC-3363 High Voltage Battery Rescue Charger. This may be due to the software level of the Midtronics xRC-3363 High Voltage Battery Rescue Charger. |
| 24U06 S1 | 2024-08-07. Service bulletin. UNKNOWN OR OTHER. Certain 2024 Model Year Bronco Sport, Escape, and Explorer Keyless Entry Remote Control Replacement REASON FOR THIS SUPPLEMENT • Affected Vehicle Build Dates: The build date range for the affected vehicles has been updated to include additional vehicle population. • Technical Instructions: Remote control serial number identification inspection has been updated. |
| SSM 52722 | 2024-08-06. Service bulletin. UNKNOWN OR OTHER. Some 2019-2024 Ford and Lincoln vehicles equipped with SYNC3 may experience various FordPass/LincolnWay connectivity concerns including but not limited to: missing activation prompt (pop-up) on the vehicle's center display screen when attempting to activate vehicle through FordPass/LincolnWay, incorrect location/global positioning system (GPS) reported through FordPass/LincolnWay, problems with remote commands being performed through FordPass/LincolnWay, incorrect data/information reported on FordPass/LincolnWay. These symptoms will be accompanied by diagnostic trouble code (DTC) B156D:89 in the TCU. This may be due the accessory protocol interface module (APIM) software |
| SSM 52704 | 2024-08-05. Service bulletin. UNKNOWN OR OTHER. Some 2019-2024 vehicles equipped with SYNC 3 may experience a programming Error - "INSTL_ERR12" while programming APIM using the Ford Diagnosis and Repair System (FDRS) or experience a frozen screen which says "updating system software" or no progress/response from module using the universal USB updater. This may be due to low memory in the APIM commonly occurring on software level NU5T-14G381-AB/BB. The current software level can be verified in the SYNC tab of Professional Technician System (PTS) or using the vehicle's center display screen, Settings > General > About. To correct the condition, run the universal USB updater. If unsuccessful, using the latest software version of the FDRS scan tool, run the service function "APIM - Reset the Accessory Protocol Interface Module Application" and select "Clear All User Data" option. The center display screen will reboot. As soon as the vehicle's center display screen displays the boot up logo, immediately reinsert the same universal serial bus (USB) drive that was utilized during the prior failed programming attempt. |
| SSM 52675 | 2024-07-03. Service bulletin. UNKNOWN OR OTHER. Some 2019-2024 vehicles equipped with SYNC 3 may experience a programming Error - "INSTL_ERR12" while programming APIM using the Ford Diagnosis and Repair System, or experience a frozen screen which says "updating system software" or no progress/response from module using the universal USB updater. This may be due to low memory in the APIM commonly occurring on software level |
| SSM 52652 | 2024-07-03. Service bulletin. ELECTRICAL SYSTEM. On 2020-2024 Explorer/Police Interceptor Utility vehicles, customers may desire modifications that require access to the driver's door ajar circuit. In some cases customers may experience an ajar light on when the driver's door is fully closed. When using pin 13 on the factory 14-way connector to access the driver's door ajar circuit, a 70 mA maximum coil current relay with an integrated clamping diode is required to protect against damage to the door latch. Failure to install this correctly will result in repeat warnings that the driver's door latch/door ajar light will remain on until it is compliant with police modifier's bulletin P-032, which can be found on the Police body builder's site (https://fordbbas.com/publications). |
| TSB 24-2182 | 2024-06-13. Service bulletin. UNKNOWN OR OTHER. This article supersedes TSB 23-2307 to update the Service Procedure and vehicle model years affected. Some 2019-2020 Edge/F-150/Fusion/Continental/MKZ/Nautilus, 2019-2021 Transit Connect, 2019-2023 Mustang, 2019-2023 Ranger, 2020-2021 Expedition/Navigator, 2020-2022 Escape/Corsair/Super Duty/EcoSport, 2020-2024 Explorer/Aviator/Transit, 2021-2024 Bronco Sport, 2022-2024 Maverick vehicles with SYNC 3 may experience various SYNC performance related concerns. This may be due to the SYNC Software. To correct the condition, follow the Service Procedure to update theaccesory protocol interface module (APIM) software. |
| 24U06 | 2024-06-06. Service bulletin. UNKNOWN OR OTHER. Certain 2024 Model Year Bronco Sport, Escape, and Explorer - Keyless Entry Remote Control Replacement |
| SSM 52548 | 2024-05-23. Service bulletin. POWER TRAIN. Various vehicles equiped with 10R80/10R80 MHT/10R100/10R140 transmissions may require replacement of the seal kits (7153) when internal repairs are being performed. These kits come with 4 wheel drive (4WD) seals and will no longer include the 2WD seals. When working on a 2WD vehicle, any 2WD seals must be ordered separately. Refer to the parts catalog for the proper 2WD seals required. |
| SSM 52543 | 2024-05-23. Service bulletin. ELECTRICAL SYSTEM. Some 2021-2024 F-150-3.5L FHEV, 2020-2024 Explorer 3.3L FHEV, 2020-2024 Escape 2.5L FHEV, and 2022-2024 Maverick 2.5L FHEV vehicles may exhibit an illuminated MIL with DTC P237F and/or P2C23 stored in the powertrain control module (PCM) and no affect on drivability. This may be due to seal damage, corrosion and/or water intrusion in the exhaust coolant temperature (ECT) sensors 3 and/or 4 connector. Visual inspection should be completed on ECT3 and ECT4 sensors and mating connections for seal damage, water intrusion, and corrosion. If seal damage, water intrusion or corrosion is present, repair per cell 5 of the Wiring Diagram, then apply Motorcraft® XG-12 Electrical Grease to the female/vehicle side of the harness. This inspection of ECT3 and ECT4 sensors should be completed prior to starting the appropriate pinpoint test in Section 303-03 of the Workshop Manual (WSM). If DTCs P237F and/or P2C23 do not return, no further action is necessary and the replacement of the entire exhaust heat exchanger assembly is not required. If P237F and/or P2C23 returns, follow the pinpoint test in Section 303-03 of the WSM for further diagnostics. |
| SSM 52509 | 2024-05-17. Service bulletin. UNKNOWN OR OTHER. Some 2023-2024 Police Interceptor Utility vehicles built on 04-Dec-2023 and through 16-Apr-2024 may exhibit a condition where FordPass is inoperative, Fleet Telematics cannot be enrolled and/or the TCU fails provisioning with the parameter identification (PID) for TCU Auth mode reading as Unprovisioned mode. This may be due to incorrect configuration data in the TCU, audio front control module (ACM) and/or accessory protocol interface module (APIM) modules. To correct the condition, download and run the TCU-Telematics Control Unit (TCU) Module Configuration application and the APIM-Accessory Protocol Interface Module (APIM) Configuration application using the latest level of the Ford Diagnosis and Repair System (FDRS) scan tool. If the APIM is not available on the vehicle, then run the configuration applications for the TCU-Telematics Control Unit (TCU) Module Configuration and the ACM-Audio Front Control Module (ACM) Configuration using the latest level of the FDRS scan tool. For claiming, use causal part 14G087 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual. |
| SSM 52503 | 2024-05-17. Service bulletin. FUEL/PROPULSION SYSTEM. Some 2023-2024 Explorer/Aviator vehicles equipped with the 3.0L EcoBoost engine and up to 15,000 miles (24,140 km) may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P219A (Bank 1 Air-Fuel Ratio Imbalance) and/or P219B (Bank 2 Air-Fuel Ratio Imbalance) stored in the powertrain control module (PCM) with no effect on vehicle operation. To correct this condition, replace the fuel injector assemblies (service part L1MZ-9F593-B) for only the respective bank setting the DTC. Refer to Workshop Manual, Section 303-04B. For claiming, use causal part 9F593 and applicable labor standards in Section 10 of the Service Labor Time Standards (SLTS) Manual. |
| SSM 52482 | 2024-05-03. Service bulletin. UNKNOWN OR OTHER. Some 2020-2024 Explorer/Aviator vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P0627, P025A, P025B, P00C6, P008A and/or U0109 stored in the powertrain control module (PCM). Diagnosis should include checking the fuel pump monitor (VE518) and/or a fuel pump control (VE225) circuits, connector pin push-outs, damaged pins/terminals, and/or loose/corroded grounds. Inspect FPCM connector C433/C4033, ground G407, and inline connections C1147 and C3136 for being fully seated and damage free prior to performing guided diagnostics or replacing any components. |
| SSM 52476 | 2024-05-03. Service bulletin. EQUIPMENT. All accessory stick-on keyless entry keypads come with a wallet card containing the master code. If the accessory keypad was factory installed, this card will be placed in the glove box and should be handed to the vehicles owner during initial delivery. Unlike the integrated (wired) factory keypad, the accessory keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool. If the wallet card for an accessory keypad is lost, follow these steps to recover the code. Dealer Key Code access is granted through the Dealer Program Enrollment System (DPES); dealership management can authorize users. The authorized user must go to FMCDealer.com > Parts and Service > Parts Product Line Information > Keys/Entry Devices > Aftermarket Keyless Entry Keypad Code Access. Follow the instructions on the screen to obtain the master code for the accessory keypad. |
| SSM 52390 | 2024-04-04. Service bulletin. EQUIPMENT; BACK OVER PREVENTION: SENSING SYSTEM: CAMERA. Some 2023-2024 Explorer vehicles built on or after 31-Jul-2023 (minor feature code J3KAJ which can be confirmed by double-clicking the VIN on PTS in the upper left corner) are no longer equipped with the 360 degree view camera or reverse brake assist features. Vehicles affected are equipped with only rear functioning cameras. The vehicle is not misbuilt. Do not submit a claim for this condition. Affected vehicles of this change can be verified by entering a vehicle identification number (VIN) on Professional Technician System (PTS) to check for a 360-degree camera credit on the window sticker. Diagnosis and repair for any parking aid concerns on these vehicles should follow Workshop Manual (WSM) Section 413-13B for Rear Parking Aid Camera System only. Do not use the 360 degree view camera or reverse brake assist diagnostics or repair procedures. |
| SSM 52351 | 2024-04-04. Service bulletin. EQUIPMENT; VISIBILITY:DEFROSTER/DEFOGGER/HVAC SYSTEM. Certain 2023-2024 Explorer vehicle trim levels built on or after 6-Feb-2023 are no longer equipped with the rear heating ventilation and air conditioning (HVAC) control panel on the rear of the center console. The following Explorer trim levels no longer include the rear HVAC control panel: Base, XLT 200A, XLT 202A without the Sport Appearance Package (sales code: 68M). Customers can adjust the rear climate control system via the front HVAC control panel. Installation of a rear HVAC control panel is not warrantable. |
| SSM 52348 | 2024-03-20. Service bulletin. ELECTRICAL SYSTEM:IGNITION:ANTI-THEFT:IMMOBILIZER/PROXIMITY:KEY/SENDER. 2024 Explorer/Aviator vehicle key fobs are shipped from the factory zip tied together. If the vehicle does not come with the key fob pairs zip tied together at transport delivery to the dealership, validate that both key fobs work. If both key fobs do not work or if only one key fob is present when vehicle is recieved at transport delivery to the dealership, a claim must be made using the Delivery App, or delivery receipt/ePOD process. This is not a warrantable item as per the warranty policy manual section 2.1.00. Note that zip tied key fobs might not allow the Passive Entry feature to function correctly. |
| SSM 52335 | 2024-03-20. Service bulletin. ENGINE AND ENGINE COOLING. For 2015-2024 Ford and Lincoln vehicles equipped with turbocharged engines and customer concern of an engine oil leak, refer to Workshop Manual (WSM), Section 303-00 for oil leak inspection and testing methods. Ford has evaluated turbochargers replaced for oil leak symptoms and although oil may collect on the external surface of a turbocharger, it is extremely rare for a turbocharger assembly to be the root cause of the oil leak. Careful inspection of the turbocharger oil feed and drain tubes should be performed along with the recommended WSM procedures as needed. Warranty claims for turbocharger replacement going forward will be assessed. |
| SSM 52314 | 2024-03-20. Service bulletin. POWER TRAIN. During service and repair requiring removal and replacement of a crankshaft bolt and/or crankshaft damper, achieving proper torque of the crankshaft pulley bolt is critical. Incorrect torque may allow the bolt to loosen resulting in the timing gear breaking and engine damage. Replacement of the bolt is critical to the repair and accurately following the installation procedure in the Workshop Manual (WSM) Section, 303-01 is extremely important. The bolt torque procedure can be found in the crankshaft front seal removal and installation procedure or in the engine assembly procedure. |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.