WenmarOpen by Wenmar Pro

Service bulletins for the 2024 Ford Escape

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

163 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

Only bulletins with component: Transmission and driveline are shown. Show all

Bulletins, newest first
SSM 537642025-05-21. Service bulletin. POWER TRAIN; ENGINE. Some 2020 Continental, 2020-2024 Edge/Nautilus, 2020-2025 Explorer/Aviator/Escape/Corsair/F-150/F-Super Duty/Ranger/Transit/E-Series, 2021-2025 Bronco, and 2022-2025 Maverick vehicles may require an engine cooling system flush to be performed for various concerns. Workshop Manual (WSM), Section 303-03 has been updated to eliminate the need to remove and install the radiator assembly to perform a radiator flush.
24B262024-10-03. Service bulletin. POWER TRAIN. In all of the affected vehicles, the transmission sun gear bearing was incorrectly installed and may cause premature failure of the transmission.
TSB 24-21932024-09-24. Service bulletin. POWER TRAIN. Some 2023-2024 Escape vehicles equipped with a HF45 transmission may exhibit an illuminated powertrain malfunction (wrench) indicator with DTC P07E6 stored in the inverter system controller SOBDMC, the GSM will display a flashing P on the dial, the P on the instrument cluster is not illuminated, and the vehicle will be stuck in the park (P) position.
TSB 24-22462024-08-19. Service bulletin. POWER TRAIN. Some 2023-2024 Escape vehicles built on or before 10-Jun-2024 and equipped with 1.5L engine may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P0496 stored in the powertrain control module (PCM). To correct this condition, follow the Service Procedure to reprogram the PCM.
TSB 24-21392024-06-03. Service bulletin. POWER TRAIN. Some 2020-2024 Escape and Corsair Vehicle equipped with the 8F35 or the HF45 transmission may exhibit a click or ting noise during acceleration from a stop, or in some cases during the end of a stop event. This may be due to the front half shaft sticking to the wheel bearing surface. To correct this condition, perform the Service Procedure below to lubricate the halfshaft and wheel bearing hub assembly mating surface.
SSM 524192024-04-24. Service bulletin. POWER TRAIN. Some 2023-2024 Escape/Corsair vehicles equipped with a 1.5L or 2.0L EcoBoost engine, 2024 Mustang vehicles equipped with a 2.3L EcoBoost engine, and 2024 Nautilus vehicles may exhibit an engine misfire condition with diagnostic trouble codes (DTC) P0301, P0302, P0303 and/or P0304 set in the powertrain control module (PCM). If the codes are stored in the PCM, remove and inspect the condition of all the spark plugs. If any spark plugs appear to be damaged, use a borescope to inspect the condition of the cylinder walls. If the cylinder walls are scored/scraped/damaged, replace the long block engine assembly (6006) to resolve this condition. If the cylinder walls are not scored/scraped/damaged, replace the damaged spark plug(s) and advise the customer that engineering is investigating this issue. Monitor OASIS for additional information and schedule service appointments for customers once the repair becomes available.
TSB 24-20782024-04-03. Service bulletin. POWER TRAIN. This article supersedes TSB 23-2244 to add 2024 model year. Some 2020-2024 Escape hybrid vehicles equipped with a 2.5L (FHEV) full hybrid electric vehicle powertrain and 4-wheel drive (4WD) may exhibit a grinding or rubbing noise while braking at or below 10 mph (16 km/h) from the front of the vehicle. This may be due to an inadequate gap between the driveshaft and the heat shield. To correct this condition, follow the Service Procedure to diagnose and position the heat shield away from the driveshaft.
SSM 523142024-03-20. Service bulletin. POWER TRAIN. During service and repair requiring removal and replacement of a crankshaft bolt and/or crankshaft damper, achieving proper torque of the crankshaft pulley bolt is critical. Incorrect torque may allow the bolt to loosen resulting in the timing gear breaking and engine damage. Replacement of the bolt is critical to the repair and accurately following the installation procedure in the Workshop Manual (WSM) Section, 303-01 is extremely important. The bolt torque procedure can be found in the crankshaft front seal removal and installation procedure or in the engine assembly procedure.
SANVol 2 Issue 12024-02-06. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); POWER TRAIN; ELECTRICAL SYSTEM. The Service Awareness Newsletter is an informal communication that contains information that may not be presently available in a TSB, SSM, GSB, or other electronic communication. This artile includes ifnormation on warranty, technical service tips and other service information.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.