P1285 on the 2023 Ford Escape
The bulletins listed name this code in NHTSA's summary, or are about the same components. A bulletin or a recall listed here may apply to the model year. None of it is a diagnosis.
This code is specific to a manufacturer and is not described here. Its meaning is in the manufacturer's service information.
| SSM 55142 | 2026-09-04. Service bulletin. Some 2023-2025 Escape vehicles built on or before 16-Sep-2024 equipped with 1.5L EcoBoost engine may exhibit an "Engine Coolant Over-Temperature" warning message displayed in the IPC and an illuminated MIL with DTCs P1285 and/or P1299 stored in the powertrain control module (PCM) during hard acceleration or under high load conditions. This may be due to machining chips trapped in the cylinder head causing a potential blockage in the coolant passage near the cylinder head temperature 2 (CHT2) port. To diagnose this condition, start the vehicle and idle for 15 minutes. Perform a road test at a temperature above -20°C (-4°F) and apply wide-open throttle (WOT) hard accelerations in rapid succession. If the concern cannot be replicated, drain and refill the coolant system. If the concern can be replicated, drain the coolant system. Perform the Engine Cooling System Flushing procedure in Workshop Manual (WSM) > 303-03A Engine Cooling - 1.5L EcoBoost > General Procedures. Do not use the VC1 flush additive. Reassemble the engine. Fill and bleed the coolant system and re-evaluate the concern. If the concern pers |
|---|---|
| SSM 54288 | 2025-10-14. Service bulletin. Some 2023-2025 Escape vehicles built on or before 16-Sep-2024 equipped with 1.5L EcoBoost engine may exhibit an "Engine Coolant Over-Temperature" warning message displayed in the IPC and an illuminated MIL with DTCs P1285 and/or P1299 stored in the powertrain control module (PCM) during hard acceleration or under high load conditions. This may be due to machining chips trapped in the cylinder head causing a potential blockage in the coolant passage near the cylinder head temperature 2 (CHT2) port. To diagnose this condition, start the vehicle and idle for 15 minutes. Perform a road test at a temperature above -20°C (-4°F) and apply wide-open throttle (WOT) hard accelerations in rapid succession. If the concern cannot be replicated, drain and refill the coolant system. If the concern can be replicated, drain the coolant system. Perform the Engine Cooling System Flushing procedure in Workshop Manual (WSM) > 303-03A Engine Cooling - 1.5L EcoBoost > General Procedures. Do not use the VC1 flush additive. Reassemble the engine. Fill and bleed the coolant system and re-evaluate the concern. |
| SSM 54114 | 2025-08-07. Service bulletin. Some 2023-2025 Escape vehicles built on or before 16-Sep-2024 equipped with 1.5L EcoBoost engine may exhibit an "Engine Coolant Over-Temperature" warning message displayed in the IPC and an illuminated MIL with DTCs P1285 and/or P1299 stored in the powertrain control module (PCM) during hard acceleration or under high load conditions. This may be due to machining chips trapped in the cylinder head causing a potential blockage in the coolant passage near the cylinder head temperature 2 (CHT2) port. To diagnose this condition, start the vehicle and idle for 15 minutes. Perform a road test at a temperature above -20°C (-4°F) and apply wide-open throttle (WOT) hard accelerations in rapid succession. If the concern cannot be replicated, drain and refill the coolant system. If the concern can be replicated, drain the coolant system. Perform the Engine Cooling System Flushing procedure in Workshop Manual (WSM) > 303-03A Engine Cooling - 1.5L EcoBoost > General Procedures. Do not use the VC1 flush additive. Reassemble the engine. Fill and bleed the coolant system and re-evaluate the concern. If the concern pers |
| SSM 54068 | 2025-07-30. Service bulletin. Some 2023-2025 Escape vehicles built on or before 16-Sep-2024 equipped with 1.5L EcoBoost engine may exhibit an "Engine Coolant Over-Temperature" warning message displayed in the IPC and an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P1285 and/or P1299 stored in the powertrain control module (PCM) during hard acceleration or under high load conditions. This may be due to machining chips trapped in the cylinder head causing a potential blockage in the coolant passage near the cylinder head temperature 2 (CHT2) port. To diagnose this condition, start the vehicle and idle for 15 minutes. Perform a road test at a temperature above -20°C (-4°F) and apply wide-open throttle (WOT) hard accelerations in rapid succession. If the concern cannot be replicated, drain and refill the coolant system. If the concern can be replicated, drain the coolant system. Disconnect the charge air cooler inlet and outlet hose, overflow hose, upper and lower hose of the radiator and position these components aside. Disconnect the inlet and outlet coolant hoses of the heater core and position |
| SSM 52219 | 2024-02-06. Service bulletin. Some 2023-2024 Escape vehicles built on or before 11-Jan-2024 equipped with 1.5L engines may exhibit an Engine Coolant Over-Temperature Warning message displayed in the IPC and an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P1285 and/or P1299 stored in the powertrain control module (PCM) during hard acceleration or under high load conditions. This may be due to machining chips trapped in the cylinder head causing a potential blockage in the coolant passage near the cylinder head temperature (CHT2) port. To diagnose this condition, start the vehicle and idle for 15 minutes. Perform a road test at a temperature above -20°C (-4°F) and apply wide-open throttle (WOT) hard accelerations in rapid succession. If the concern can not be replicated, drain and refill the coolant system. If the concern can be replicated, drain the coolant system. Disconnect the charge air cooler inlet and outlet hose, overflow hose, upper and lower hose of the radiator and position these components aside. Disconnect the inlet and outlet coolant hoses of the heater core and position these compone |
| SSM 52162 | 2024-01-18. Service bulletin. Some 2023 Escape vehicles equipped with 1.5L engines may exhibit an Engine Coolant Over-Temperature Warning message displayed in the instrumental panel cluster (IPC) and an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P1285 and/or P1299 stored in the powertrain control module (PCM) during hard acceleration or under high load conditions. Ford is aware of the concern and this condition does not affect vehicle durability and no additional diagnosis or service is required for this condition at this time. Inform customers that they can continue to drive the vehicle and engineering is currently working on a solution for this condition that is expected in Q1 of 2024. Replacement of the cylinder head temperature (CHT) sensor may not resolve this condition. Monitor OASIS for additional information and schedule service appointments for customers once the repair becomes available. |
6 on file from NHTSA, as of 2026-10-19. See them in the bulletin list. A bulletin lists model years: read the document for which vehicles it concerns.