WenmarOpen by Wenmar Pro

Service bulletins for the 2017 Ford Escape

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

249 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Only bulletins with component: Engine are shown. Show all

Bulletins, newest first
SSM 523352024-03-20. Service bulletin. ENGINE AND ENGINE COOLING. For 2015-2024 Ford and Lincoln vehicles equipped with turbocharged engines and customer concern of an engine oil leak, refer to Workshop Manual (WSM), Section 303-00 for oil leak inspection and testing methods. Ford has evaluated turbochargers replaced for oil leak symptoms and although oil may collect on the external surface of a turbocharger, it is extremely rare for a turbocharger assembly to be the root cause of the oil leak. Careful inspection of the turbocharger oil feed and drain tubes should be performed along with the recommended WSM procedures as needed. Warranty claims for turbocharger replacement going forward will be assessed.
SSM 514092023-04-04. Service bulletin. ENGINE AND ENGINE COOLING. Some 2014-2020 Fusion and 2017-2019 Escape vehicles may be equipped with a 1.5L Ecoboost engine that uses a 50-tooth variable camshaft timing (VCT) intake and exhaust unit from the assembly plant or if a service long block was installed. VCT locking tool 303-1097 is not compatible with this system. If VCT system service is required, replace both the intake VCT (service part DS7Z-6256-F) and exhaust VCT (service part DS7Z-6256-G) as a pair. An interim loaner tool program has been established to enable these repairs. Contact 1-800-403-4844 (Monday-Friday 8:00am to 8:00pm EST; Saturday 8:00am to 3:00pm EST) to obtain this tool. A VCT locking tool compatible with the 50-tooth system is under development and will be sent to dealerships. Continue to monitor OASIS for additional information.
TSB 22-23222022-08-23. Service bulletin. ENGINE AND ENGINE COOLING. Some 2014-2019 Fusion vehicles built on or before 10-Jun-2019 and 2017-2019 Escape vehicles built on or before 08-Apr-2019 equipped with a 1.5L EcoBoost engine may exhibit low coolant level, white exhaust smoke and/or runs rough condition with or without an illuminated malfunction indicator light (MIL) with only diagnostic trouble codes (DTCs) P0300, P0301-P0304, P0316, P0217, P1285 and/or P1299 stored in powertrain control module (PCM). This may be due to coolant intrusion into the cylinder. To resolve the condition, follow the Service Procedure to replace the short block and head gasket.
19B372022-06-13. Service bulletin. ENGINE AND ENGINE COOLING. Certain 2017-2019 Model Year Fusion and Escape Vehicles Equipped with a 1.5L GTDI Engine - Powertrain Control Module Programming - Some of the affected vehicles may exhibit collant intrusion into the cylinder bores. Customer symptoms include coolant loss, excessive tailpipe smoke, or illuminated malfunction indicator lights (MIL) due to engine misfire. Over time, this condition may damage the engine, requiring replacement of the short block.
TSB 22-22292022-06-13. Service bulletin. ENGINE AND ENGINE COOLING. Some 2015-2018 Edge and 2017-2019 Fusion/MKZ/Escape/MKC vehicles equipped with a 2.0L EcoBoost engine may exhibit a low coolant level, white exhaust smoke and/or a runs rough condition with or without an illuminated malfunction indicator lamp (MIL). Diagnostic trouble codes (DTCs) may include P0300, P0301-P0304, P0316, P0217, P1285 and/or P1299 stored in powertrain control module (PCM). This may be due to coolant intrusion into the cylinder. To correct the condition, follow the Service Procedure to replace the long block engine assembly.
21N122022-06-10. Service bulletin. ENGINE AND ENGINE COOLING. Certain 2017-2019 Model Year Fusion and Escape Vehicles Equipped with a 1.5L GTDI Engine – Short Block Replacement After Coolant Intrusion. In some of the affected vehicles the 1.5L EcoBoost engine may exhibit a low coolant level, white exhaust smoke and/or may run in a rough condition with or without an illuminated malfunction indicator light (MIL) with only diagnostic trouble codes (DTCs) P0300, P0301-P0304, P0316, P0217, P1285 and/or P1299 stored in powertrain control module (PCM). This may be due to coolant intrusion into a cylinder bore.
19B37-S42022-06-10. Service bulletin. ENGINE AND ENGINE COOLING; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE:SOFTWARE. Certain 2017-2019 Model Year Fusion and Escape Vehicles Equipped with a 1.5L GTDI Engine - Powertrain Control Module Reprogramming. Some of the affected vehicles may exhibit coolant intrusion into the cylinder bores. Customer symptoms include coolant loss, excessive tailpipe smoke, or illuminated malfunction indicator lights (MIL) due to engine misfire. Over time, this condition may damage the engine, requiring replacement of the engine short block.
TSB 22-21342022-04-20. Service bulletin. ENGINE AND ENGINE COOLING; EQUIPMENT. Some 2014-2019 Fusion vehicles built on or before 10-Jun-2019 and 2017-2019 Escape vehicles built on or before 08-Apr-2019 equipped with a 1.5L EcoBoost engine may exhibit low coolant level, white exhaust smoke and/or runs rough condition with or without an illuminated malfunction indicator light (MIL) with only diagnostic trouble codes (DTCs) P0300, P0301-P0304, P0316, P0217, P1285 and/or P1299 stored in powertrain control module (PCM). This may be due to coolant intrusion into the cylinder. To resolve the condition, follow the Service Procedure to replace the short block and head gasket.
TSB 22-21332022-04-20. Service bulletin. EQUIPMENT; ENGINE AND ENGINE COOLING. Some 2015-2018 Edge and 2017-2019 Fusion/MKZ/Escape/MKC vehicles equipped with a 2.0L EcoBoost engine may exhibit a low coolant level, white exhaust smoke and/or a runs rough condition with or without an illuminated malfunction indicator lamp (MIL). Diagnostic trouble codes (DTCs) may include P0300, P0301-P0304, P0316, P0217, P1285 and/or P1299 stored in powertrain control module (PCM). This may be due to coolant intrusion into the cylinder. To correct the condition, follow the Service Procedure steps to replace the long block engine assembly.
SSM 504392022-02-04. Service bulletin. ENGINE AND ENGINE COOLING. Some 2017-2020 Fusion/MKZ and 2017-2019 Escape/MKC vehicles equipped with a 2.0L EcoBoost engine may require replacement of the long block engine assembly. New service kits have been released which include all the one-time-use components required in the service procedure for removal and replacement of the long block engine assembly. Refer to the Ford Electronic Parts Catalog (ECAT) for long block service kit part number by application.
TSB 21-22692021-09-30. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); ENGINE AND ENGINE COOLING. Some 2014-2019 Fusion vehicles built on or before 10-Jun-2019 and 2017-2019 Escape vehicles built on or before 08-Apr-2019 equipped with a 1.5L EcoBoost engine may exhibit low coolant level, white exhaust smoke and/or runs rough condition with or without an illuminated malfunction indicator light (MIL) with only diagnostic trouble codes (DTCs) P0300, P0301-P0304, P0316, P0217, P1285 and/or P1299 stored in powertrain control module (PCM). This may be due to coolant intrusion into the cylinder. To resolve the condition, follow the Service Procedure to replace the short block and head gasket.
SSM 498212021-06-01. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION; ENGINE AND ENGINE COOLING. Some 2015-2021 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTC) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK11 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 495962021-03-03. Service bulletin. ENGINE AND ENGINE COOLING. Some 2017-2019 Escape/Fusion vehicles may exhibit a rolling idle after an engine repair that required the crankshaft pulley removal, or a drive belt component failure. The crankshaft pulley to be slightly out of alignment in relation to engine top dead center (TDC) causing an incorrect crankshaft position (CKP) sensor signal. To determine this as the cause of the rolling idle, position the crankshaft at TDC using essential special service tool (ESST) 303-748 then remove the CKP Sensor and attempt to install ESST 303-1550. If the bolt to hold 303-1550 cannot be installed by hand, this indicates that the crank pulley is not properly installed. Using a new crank bolt, install the pulley/vibration damper in its proper alignment following the WSM procedure in 303-01. Use ESST 303-393A to hold the flexplate/crankshaft when torqueing down the crank bolt.
SSM 492102020-10-06. Service bulletin. ENGINE AND ENGINE COOLING. Some 2009-2020 Ford and Lincoln vehicles equipped with turbochargers may exhibit an oil leak from the turbocharger oil supply or return tubes, O-rings or 6.7L pedestal gasket. Although oil may collect on the turbocharger, it is very rare for a turbocharger to leak oil. To isolate the source of the leak, refer to Workshop Manual (WSM), Section 303-00 General Information > Diagnosis and Testing > Engine > Engine Oil Leaks - Fluorescent Oil Additive Method procedure. When an oil leak is present at a turbocharger oil supply or drain tube, remove the affected oil tube and inspect for damage, and replace the O-ring seals, pedestal gasket or oil tube as required. Refer to WSM, Section 303-04. For claiming, use the affected oil tube or pedestal gasket as the causal part and applicable labor operations in Sections 6 and 9 of the Service Labor Time Standards (SLTS) Manual.
SSM 488952020-07-07. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); ENGINE; ELECTRICAL SYSTEM. Some 2017-2019 Escape vehicles equipped with a 1.5L or 2.0L engine may exhibit fuse F34 open with an illuminated MIL and diagnostic trouble codes (DTCs) P0034, P023A, P0245, P0480, P0481, P0645, P06A0, P06DB, P188D, P02602, and/or P2681 in the powertrain control module (PCM). The vehicle may also exhibit an all-wheel drive (AWD) fault warning and/or illuminated traction control (TC) lamp. Inspect the 12A690 (1.5L) or 12C508 (2.0L) wiring harness from the battery junction box (BJB) to the PCM for wiring harness retainers not installed correctly allowing chafing to occur at multiple points. Repair damaged wiring as required. Refer to the Wiring Diagram for repair information. For claiming, use causal part 12A690 (1.5L) or 12C508 (2.0L) and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
19B37-S32020-06-05. Service bulletin. ENGINE AND ENGINE COOLING; POWER TRAIN:AUTOMATIC TRANSMISSION. Some of the affected vehicles may exhibit coolant intrusion into the cylinder bores. Customer symptoms include coolant loss, excessive tailpipe smoke, or illuminated malfunction indicator lights (MIL) due to engine misfire. Over time, this condition may damage the engine, requiring replacement of the engine short block.
TSB 20-21002020-05-05. Service bulletin. ENGINE AND ENGINE COOLING. Some 2014-2019 Fusion vehicles built on or before 10-Jun-2019 and 2017-2019 Escape vehicles built on or before 08-Apr-2019 equipped with a 1.5L EcoBoost engine may exhibit low coolant level, white exhaust smoke and/or runs rough condition with or without an illuminated malfunction indicator light (MIL) with only diagnostic trouble codes (DTCs) P0300, P0301-P0304, P0316, P0217, P1285 and/or P1299 stored in powertrain control module (PCM). This may be due to coolant intrusion into the cylinder. To resolve the condition, follow the Service Procedure to replace the short block and head gasket.
19B37-S12020-02-04. Service bulletin. ENGINE AND ENGINE COOLING. Some of the affected vehicles may exhibit coolant intrusion into the cylinder bores. Customer symptoms include coolant loss, excessive tailpipe smoke, or illuminated malfunction indicator lights (MIL) due to engine misfire. Over time, this condition my damage the engine, requiring replacement of the engine short block.
TSB 19-23752020-01-07. Service bulletin. ENGINE AND ENGINE COOLING. This article supersedes TSB 19-2139 to update the production fix date. Some 2014-2019 Fusion vehicles built on or before 10-Jun-2019 and 2017-2019 Escape vehicles built on or before 08-Apr-2019 equipped with a 1.5L EcoBoost engine may exhibit low coolant level, white exhaust smoke and/or runs rough condition with or without an illuminated malfunction indicator light (MIL) with only diagnostic trouble codes (DTCs) P0300, P0301-P0304, P0316, P0217, P1285 and/or P1299 stored in powertrain control module (PCM). This may be due to coolant intrusion into the cylinder. To resolve the condition, replace the short block and head gasket.
TSB 19-23462020-01-07. Service bulletin. ENGINE AND ENGINE COOLING. Some 2015-2018 Edge and 2017-2019 Fusion/MKZ/Escape/MKC vehicles equipped with a 2.0L EcoBoost engine may exhibit a low coolant level, white exhaust smoke and/or a runs rough condition with or without an illuminated malfunction indicator lamp (MIL). Diagnostic trouble codes (DTCs) may include P0300, P0301-P0304, P0316, P0217, P1285 and/or P1299 stored in powertrain control module (PCM). This may be due to coolant intrusion into the cylinder. To correct the condition, follow the Service Procedure steps to replace the long block engine assembly.
TSB 19-23472019-12-04. Service bulletin. POWER TRAIN; ENGINE AND ENGINE COOLING. Some 2017 Escape vehicles equipped with a 1.5L EcoBoost engine may exhibit an malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P051B stored in the powertrain control module (PCM). This may be due to the crankcase pressure sensor/tube assembly. To correct the condition, follow the Service Procedure steps to replace the crankcase pressure sensor/tube assembly.
TSB 19-21392019-12-04. Service bulletin. ENGINE AND ENGINE COOLING. Some 2014-2019 Fusion vehicles built on or before 21-Feb-2019 and 2017-2019 Escape vehicles built on or before 06-Apr-2019 equipped with a 1.5L EcoBoost engine may exhibit low coolant level, white exhaust smoke and/or runs rough condition with or without an illuminated malfunction indicator light (MIL) with only diagnostic trouble codes (DTCs) P0300, P0301-P0304, P0316, P0217, P1285 and/or P1299 stored in powertrain control module (PCM). This may be due to coolant intrusion into the cylinder. To resolve the condition, replace the short block and head gasket.
SSM 481502019-09-09. Service bulletin. ENGINE AND ENGINE COOLING. Some 2014-2019 Fusion and 2017-2019 Escape with 1.5L engine may exhibit coolant usage and white smoke from exhaust. Follow Cooling System Pressure Test process in WSM, Section 303-03. Pressurize system to 138kPa(20 psi) and hold 5 hours. If system pressure drops 27.57kPa(4psi) after 5 hours and borescope inspection through spark plug holes shows coolant presence in bores, the short block must be replaced. Further teardown inspection is not required, nor is completing cost cap. Cost cap requirements are waived for repairs completed utilizing this SSM. Reuse the original cylinder head for the repair. Ford has found all returned 1.5L cylinder heads pass inspection and replacement was not required. Follow WSM, Section 303-01A for repair procedure and refer the parts catalog as needed. Any backorders experienced will be filled as quickly as possible.
SSM 481062019-08-07. Service bulletin. ENGINE AND ENGINE COOLING. Some 2014-2019 Fusion and 2017-2019 Escape vehicles with 1.5L Ecoboost engine exhibiting coolant consumption and white smoke from the exhaust. Follow Cooling System Pressure Test procedure in WSM, Section 303-03, and pressurize system to 138kPa(20 psi) and hold for 5 hours. If system pressure drops 27.57kPa (4psi) after 5 hours and borescope inspection through spark plug holes confirms coolant intrusion into the cylinders, short block replacement is required. Further teardown inspection is not required. Reuse the original cylinder head for the repair. Ford has found all returned 1.5L cylinder heads pass inspection and replacement was not required. Follow WSM, Section 303-01A procedures for repairs and refer the parts catalog as needed. Short block availability may be limited and temporary backorders will be filled as quickly as possible.
TSB 19-22082019-07-03. Service bulletin. ENGINE AND ENGINE COOLING. Some 2015-2018 Edge and 2017-2019 Fusion/MKZ/Escape/MKC vehicles equipped with a 2.0L EcoBoost engine may exhibit a low coolant level, white exhaust smoke and/or a runs rough condition with or without an illuminated malfunction indicator lamp (MIL). Diagnostic trouble codes (DTCs) may include P0300, P0301-P0304, P0316, P0217, P1285 and/or P1299 stored in powertrain control module (PCM). This may be due to coolant intrusion into the cylinder. To correct the condition, follow the Service Procedure steps to replace the long block engine assembly.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.