WenmarOpen by Wenmar Pro

Service bulletins for the 2017 Ford C-max

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

126 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Only bulletins with component: Engine are shown. Show all

Bulletins, newest first
TSB 22-21622022-05-12. Service bulletin. ENGINE; ELECTRICAL SYSTEM. Some 2014-2017 C-MAX Energi, 2014-2020 Fusion plug-in hybrid electric vehicle (PHEV), 2015-2017 MKZ/MKZ Hybrid/MKC, 2016-2017 MKX, 2016-2018 Focus battery electric vehicle (BEV) and 2017 Continental vehicles equipped with SYNC screens 8 inch or larger may be unable to complete modem authorization after 3G to 4G modem upgrade was performed. No Authorization Popup displayed on SYNC infotainment screen during the Authorization process. This may be due to the Sync Software. To correct the condition, follow the Service Procedure to toggle Valet Mode.
SSM 498212021-06-01. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION; ENGINE AND ENGINE COOLING. Some 2015-2021 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTC) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK11 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 485982020-03-03. Service bulletin. ENGINE AND ENGINE COOLING; EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. 2013-2018 C-Max, 2013-2020 Fusion Hybrid/MKZ Hybrid vehicles may exhibit a MIL with Diagnostic Trouble Code (DTC) P0340 and/or P0344. This may occur due to excessive moisture build up in the engine oil. Excess moisture occurs when the vehicle is driven short distances and/or less than 6,000 combined miles per year. To correct the condition, replace the camshaft position sensor (CMP) and change the engine oil. Advise the customer to perform more frequent oil changes and allow the internal combustion engine to reach operating temperature when running to prevent reoccurrence. Refer to the owners guide - maintenance - engine oil check - operating in cold climates and short driving cycles.
TSB 19-22072019-07-03. Service bulletin. ENGINE AND ENGINE COOLING; POWER TRAIN. Some 2013-2017 C-Max/Fusion/MKZ Hybrid/Energi vehicles may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P1450, P0456, P0457, P04EE and/or P04EF. This may be due to the sealing capability of the canister purge valve. To correct the condition, follow the Service Procedure steps to update the PCM software and replace the canister purge valve.
TSB19-21582019-06-05. Service bulletin. ENGINE AND ENGINE COOLING; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Some 2017-2019 Fusion Hybrid/Fusion Energi/MKZ Hybrid and 2017-2018 C-Max vehicles built on or before 27-Jan-2019 may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P013A stored in the powertrain control module (PCM). This may be due to downstream oxygen sensor parameters in the PCM software. To correct the condition, follow the Service Procedure to update the PCM software.
SSM 477902019-04-08. Service bulletin. ELECTRICAL SYSTEM; ENGINE. Some 2013-2019 Fusion/MKZ and 2013-2018 C-Max vehicles with 2.0L HEV/PHEV engine may exhibit multiple drivability or electrical concerns with one or more diagnostic trouble codes, being the most common P26C3, P26CA, P26D0, P2800, P2802, U019F and U0284. On Fusion/MKZ inspect connectors C146, C1651, C1812, C168C, C1717 and C134 for signs of water entry or corrosion. On C-Max, inspect connectors C134, C140, C144, C1651, C1717 and C1812 and service as necessary. NOTE: Connector C1717 is only equipped on PHEVs for both Fusion and C-Max.
SSM 475022018-09-24. Service bulletin. ENGINE AND ENGINE COOLING. Some 2017-2018 Fusion, MKZ and C-Max vehicles with 2.0L Gas/Electric engine may exhibit an illuminated MIL with DTC P013A in the Powertrain Control Module(PCM). This may be due to an exhaust system leak. Exhaust leak inspection should be conducted before performing Powertrain Control/Emissions Diagnostics PC/ED Manual diagnostic routines. Inspect for carbon soot/moisture witness marks at exhaust connections. Inspect welds including CMS Boss, flex pipe and flanges. Inspect Catalyst Monitor Sensor(CMS) threads and crush washer to confirm sensor is fully seated in pipe boss. Do not use Vacutec smoke machine to diagnose sensor leaks. Applying soapy water solution to exhaust connections including CMS threads, while exhaust flow is restricted at the tailpipe and exhaust system is pressurized at 5 PSI(do not exceed 5 PSI), will increase ability to identify and confirm leaks
18M022018-07-23. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL. Certain 2017 Model Year Multiple Vehicle Lines - California Emission Warranty Parts Coverage
SSM 468162017-10-21. Service bulletin. ENGINE. 2017 vehicles equipped with a 2.0L GTDI, 2.3L GTDI, or 2.5L PFI engine will either be equipped with a diamond washer on each side of a smooth-faced crankshaft timing sprocket (early build), or a crankshaft timing sprocket with laser etched faces and no diamond washers (late build). If equipped, diamond washers should be cleaned, inspected and reused, if undamaged. Diamond washers should never be installed along with a laser etched crankshaft timing sprocket. Related WSM procedure information is in the process of being updated.
SSM 460852017-08-01. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:MANIFOLD/HEADER/MUFFLER/TAIL PIPE; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:GAS RECIRCULATION VALVE (EGR VALVE); ENGINE AND ENGINE COOLING:ENGINE:OTHER FUEL TYPES:TURBO/SUPERCHARGER; ENGINE AND ENGINE COOLING:COOLING SYSTEM:HOSES/LINES/PIPING/FITTINGS; ENGINE AND ENGINE COOLING; ENGINE AND ENGINE COOLING:COOLING SYSTEM:RADIATOR ASSEMBLY; ENGINE; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CRANKCASE (PCV); ENGINE AND ENGINE COOLING:COOLING SYSTEM; ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:TURBO/SUPERCHARGER; ENGINE AND ENGINE COOLING:ENGINE:DIESEL; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM; ENGINE AND ENGINE COOLING:ENGINE:GASOLINE; ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:BELTS AND ASSOCIATED PULLEYS; ENGINE AND ENGINE COOLING:ENGINE; ENGINE AND ENGINE COOLING:COOLING SYSTEM:FAN. The Powertrain Control/Emissions Diagnosis (PC/ED) manual has been revised for diagnosing electronic throttle bodies (ETBs). The ETC_ACT and ETC_DSD PIDs should not used to diagnose possible ETB concerns. The IDS has a limited refresh rate when reading these PIDs and cannot display quickly enough to validate a concern. The PCM automatically monitors these inputs more accurately and will set diagnostic trouble codes (DTCs) when appropriate. Using these PIDs for diagnostics will lead to inaccurate results and improper ETB replacements. If a concern is intermittent and no DTCs are present, refer to historical DTCs and the PC/ED, Section 3 No DTCs Present Index chart for further information.
SSM 460762017-08-01. Service bulletin. EQUIPMENT; ENGINE. Some 2016 Model Year Fusion, MKZ and C-MAX Hybrid Electric Vehicles(HEV) vehicles equipped with 2.0L DOHC Gas/Electric engines may exhibit MIL On with Diagnostic Trouble Code P0137(O2 Sensor Circuit Low Voltage (Bank 1 Sensor 2) in Powertrain Control Module(PCM) memory and U3003 (Battery Voltage) in Battery Energy Control Module(BECM) memory due to low battery voltage. Perform Battery diagnostic tests referenced in Workshop Manual Section 414-01 Battery, Mounting and Cables-Diagnosis and Testing. After repairs for low voltage concern are repaired, clear Diagnostic Trouble Codes. If DTC P0137 and U3003 do not repeat return vehicle to the Customer. If DTC P0137 repeats perform Powertrain Control and Emissions Manual(PCED) diagnostic DW. Engineering is currently investigating this concern.
TSB 17-20722017-08-01. Service bulletin. ENGINE; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Some 2017 C-MAX/Fusion Hybrid/Energi and MKZ Hybrid vehicles may exhibit an illuminated MIL with DTC P0071 stored in the powertrain control module (PCM). This DTC can be set after the vehicle is stored inside a warm location for several hours and then driven on a cold day. Under these conditions the PCM may see a temperature sensor concern when it first compares the ambient air temperature (AAT) sensor to other engine temperature sensors and set the DTC. Reprogram the PCM to the latest calibration using Integrated Diagnostic System (IDS) release 104.04 or higher. Make sure you are connected to the internet when entering module programming to obtain the latest updates. Calibration files may also be obtained at www.motorcraftservice.com.
SSM 464102017-03-20. Service bulletin. ENGINE; EQUIPMENT:APPLIANCE:AIR CONDITIONER. SOME 2017 FUSION HEV/PHEV, C-MAX HEV/PHEV, AND MKZ HEV VEHICLES MAY EXHIBIT AN ILLUMINATED MIL WITH DTC P0071 AND/OR DEGRADED HVAC PERFORMANCE IN AUTOMATIC MODE ONLY WITH AN AMBIENT TEMPERATURE READING OF 50 DEGREES F DISPLAYED IN THE MESSAGE CENTER. IF AFTER PERFORMING NORMAL PINPOINT TEST DIAGNOSIS, A COMPONENT FAILURE IS NOT IDENTIFIED, DO NOT CONTINUE WITH FURTHER DIAGNOSIS OR PART REPLACEMENT. HAVING THE VEHICLE PARKED AND STARTED IN A WARM ENCLOSED AREA BEFORE BEING DRIVEN INTO COLD TEMPERATURES CAN INADVERTENTLY CAUSE THESE SYMPTOMS AND DTC. THE HVAC AND MESSAGE CENTER FUNCTIONS WILL RETURN TO NORMAL AFTER THE VEHICLE IS SHUT DOWN AND RESTARTED. CLEAR THE DTC USING THE FORD INTEGRATED DIAGNOSTIC TOOL (IDS) OR EQUIVALENT. ENGINEERING IS INVESTIGATING. MONITOR OASIS FOR UPDATES.
SSM 462952017-03-15. Service bulletin. ENGINE. TO HELP DIFFERENTIATE ENGINE OIL LEAKS FROM OTHER POSSIBLE SOURCES, A NEW WHITE-COLORED FLUORESCENT ENGINE OIL DYE IS AVAILABLE. WORKSHOP MANUAL (WSM), SECTION 303-00 HAS BEEN REVISED TO REFERENCE THE NEW WHITE-COLORED DYE. THE NEW WHITE FLUORESCENT DYE PROVIDES A DISTINCT WHITE GLOW TO IDENTIFY ENGINE OIL LEAKS. THE NEW WHITE FLUORESCENT DYE REQUIRES A PURE UV DIAGNOSTIC INSPECTION LAMP. THE WHITE-COLORED FLUORESCENT DYE AND PURE UV LAMP ARE NOW IN THE ROTUNDA CATALOG. DYE AND LAMP PART NUMBERS. GASOLINE ONLY DYE: 1 OUNCE BOTTLE 164-TP-33200601. DIESEL ONLY DYE: 8 OUNCE BOTTLE: 164-TP-3320-0008. PURE UV DIAGNOSTIC INSPECTION LAMP 164-TP8695 OR 164-R3748.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.