WenmarOpen by Wenmar Pro

Service bulletins for the 2024 Dodge Charger

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

270 on file from NHTSA, as of 2026-10-19.

About P0ADB on the 2024 Dodge Charger: what the code means, and the bulletins and recalls about the same components.

By type

By component

By trouble code

Only bulletins with trouble code: P0ADB are shown. Show all

Bulletins, newest first
08-311-262026-08-13. Service bulletin. POWER TRAIN; ELECTRICAL SYSTEM. Powertrain Modules Software Update Customers may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may SYMPTOM: exhibit/set one or more the following Diagnostic Trouble Codes (DTCs): ● P0AA7-00 - Hybrid/EV Battery Pack "A" Voltage Isolation Sensor. ● P1614-00 - ECU Reset/Recovery Occurred. ● B1A8A-00 - Multi-Module VIN Handshake Failure. ● P1CDB-00 - Hybrid/EV Wakeup Control 1 Output Circuit Short To Battery. ● P1E25-00 - EV Battery Failure Level 2. ● P0D10-00 - Hybrid/EV Battery Negative Contactor A Stuck Open. ● P0D09-00 - Hybrid/EV Battery Positive Contactor A Stuck Open. ● P0DE6-00 - Hybrid/EV Battery Pack Cell Voltage Low. NOTE: Active or stored. ● P1DAF - Incompatible Limp In Action Requested. NOTE: Active or stored. ● P1CDE-00 – Hybrid/EV Wakeup Control 2 Output Circuit Short to Ground. ● P1CDA-00 – Hybrid/EV Wakeup Control 1 Output Circuit/Open. ● U00C6-00 – Lost Communication With AIR Pressure Sensor. ● P0F00-00 - Hybrid/EV Battery Module 1 Performance. ● P0F01-00 - Hybrid/EV Battery Module 2 Performance. ● P0F02-00 - Hybrid/EV Battery Module 3 Performance. ● P0F03-00 - Hybrid/EV Battery Module 4 Performance. ● P0F04-00 - Hybrid/EV Battery Module 5 Performance. ● P0F05-00 - Hybrid/EV Battery Module 6 Performance. ● P0F06-00 - Hybrid/EV Battery Module 7 Performance. ● P0F07-00 - Hybrid/EV Battery Module 8 Performance. ● P0F08-00 - Hybrid/EV Battery Module 9 Performance. ● P0F09-00 - Hybrid/EV Battery Module 10 Performance. ● P0F0A-00 - Hybrid/EV Battery Module 11 Performance. ● P0F0B-00 - Hybrid/EV Battery Module 12 Performance. ● P0F0C-00 - Hybrid/EV Battery Module 13 Performance. ● P0CA6-00 - Hybrid/EV Battery Charging Current High. NOTE: If the following DTCs are present/active in the BPCM, Battery Pack replacement will be required. Guided Diagnostics will prompt you for the repair action if the diagnostic is present on the vehicle. ● P0ADB-00 - Hybrid/EV Battery Positive Contractor A Control Circuit Low. ● P0AE2-00 - Hybrid/EV Battery Precharge Contactor Circuit Stuck Closed. ● P0AA1-00 - Hybrid/EV Battery Positive Contactor "A" Stuck Closed. ● P0FF8-00 - Hybrid/EV Battery Precharge Contactor Circuit "B" Stuck Closed. Customers may also comment on one or more of the following: ● Vehicle will not start. ● A warning message will appear in the Instrument Panel Cluster (IPC) informing the driver to stop safely because the vehicle will be shutting down soon. ● Wrench icon is illuminated on the IPC. ● Vehicle will not enter Drive Ready Mode. This bulletin also includes the following software enhancements: ● Software enhancements to prevent multiple DTCs from falsely setting. ● Improved battery State of Charge (SoC) accuracy in off-nominal conditions. ● Bootloader update to prevent battery disconnect unit damage. ● Improvements in detecting pre-existing battery disconnect unit damage. ● Charging related enhancements that may lead to DTC P0CA6 falsely setting.
08-110-26 REV.A2026-03-18. Service bulletin. ELECTRICAL SYSTEM. RSU With Additional Sleep Cycles for HV Battery Integrity Check - Flash: Battery Pack Control Module (BPCM) Updates 11B3 Customers may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set one or more the following Diagnostic Trouble Codes (DTCs): ● P0AA7-00 - Hybrid/EV Battery Pack "A" Voltage Isolation Sensor. ● P1614-00 - ECU Reset/Recovery Occurred. ● B1A8A-00 - Multi-Module VIN Handshake Failure. ● P1CDB-00 - Hybrid/EV Wakeup Control 1 Output Circuit Short To Battery. ● P1E25-00 - EV Battery Failure Level 2. ● P0D10-00 - Hybrid/EV Battery Negative Contactor A Stuck Open. ● P0D09-00 - Hybrid/EV Battery Positive Contactor A Stuck Open. ● P0DE6-00 - Hybrid/EV Battery Pack Cell Voltage Low. NOTE: Active or stored. ● P1DAF - Incompatible Limp In Action Requested. NOTE: Active or stored. ● P1CDE-00 - Hybrid/EV Wakeup Control 2 Output Circuit Short to Ground. ● P1CDA-00 - Hybrid/EV Wakeup Control 1 Output Circuit/Open. ● U00C6-00 - Lost Communication With AIR Pressure Sensor. ● P0F00-00 - Hybrid/EV Battery Module 1 Performance. ● P0F01-00 - Hybrid/EV Battery Module 2 Performance. ● P0F02-00 - Hybrid/EV Battery Module 3 Performance. ● P0F03-00 - Hybrid/EV Battery Module 4 Performance. ● P0F04-00 - Hybrid/EV Battery Module 5 Performance. ● P0F05-00 - Hybrid/EV Battery Module 6 Performance. ● P0F06-00 - Hybrid/EV Battery Module 7 Performance. ● P0F07-00 - Hybrid/EV Battery Module 8 Performance. ● P0F08-00 - Hybrid/EV Battery Module 9 Performance. ● P0F09-00 - Hybrid/EV Battery Module 10 Performance. ● P0F0A-00 - Hybrid/EV Battery Module 11 Performance. ● P0F0B-00 - Hybrid/EV Battery Module 12 Performance. ● P0F0C-00 - Hybrid/EV Battery Module 13 Performance. ● P0CA6-00 - Hybrid/EV Battery Charging Current High NOTE: If the following DTCs are present/active in the BPCM, Battery Pack replacement will be required. Guided Diagnostics will prompt you for the repair action if the diagnostic is present on the vehicle. ● P0ADB-00 - Hybrid/EV Battery Positive Contractor A Control Circuit Low. ● P0AE2-00 - Hybrid/EV Battery Precharge Contactor Circuit Stuck Closed. ● P0AA1-00 - Hybrid/EV Battery Positive Contactor "A" Stuck Closed. ● P0FF8-00 - Hybrid/EV Battery Precharge Contactor Circuit "B" Stuck Closed. Customers may also comment on one or more of the following: ● Vehicle will not start. ● A warning message will appear in the Instrument Panel Cluster (IPC) informing the driver to stop safely because the vehicle will be shutting down soon. ● Wrench icon is illuminated on the IPC. ● Vehicle will not enter Drive Ready Mode. This bulletin also includes the following software enhancements: ● Software enhancements to prevent multiple DTCs from falsely setting. ● Improved battery State of Charge (SoC) accuracy in off-nominal conditions. ● Bootloader update to prevent battery disconnect unit damage. ● Improvements in detecting pre-existing battery disconnect unit damage. ● Charging related enhancements that may lead to DTC P0CA6 falsely setting This bulletin involves reprogramming the IDCM, BPCM, MCP A, MCP B and the EVCU with the latest available software and then, if needed, performing a Wheel End Disconnect Position Learn routine.
08-110-262026-03-18. Service bulletin. ELECTRICAL SYSTEM. RSU With Additional Sleep Cycles for HV Battery Integrity Check Customers may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may SYMPTOM: exhibit/set one or more the following Diagnostic Trouble Codes (DTCs): ● P0AA7-00 - Hybrid/EV Battery Pack "A" Voltage Isolation Sensor. ● P1614-00 - ECU Reset/Recovery Occurred. ● B1A8A-00 - Multi-Module VIN Handshake Failure. ● P1CDB-00 - Hybrid/EV Wakeup Control 1 Output Circuit Short To Battery. ● P1E25-00 - EV Battery Failure Level 2. ● P0D10-00 - Hybrid/EV Battery Negative Contactor A Stuck Open. ● P0D09-00 - Hybrid/EV Battery Positive Contactor A Stuck Open. ● P0DE6-00 - Hybrid/EV Battery Pack Cell Voltage Low. NOTE: Active or stored. ● P1DAF - Incompatible Limp In Action Requested. NOTE: Active or stored. ● P1CDE-00 - Hybrid/EV Wakeup Control 2 Output Circuit Short to Ground. ● P1CDA-00 - Hybrid/EV Wakeup Control 1 Output Circuit/Open. ● U00C6-00 - Lost Communication With AIR Pressure Sensor. ● P0F00-00 - Hybrid/EV Battery Module 1 Performance. ● P0F01-00 - Hybrid/EV Battery Module 2 Performance. ● P0F02-00 - Hybrid/EV Battery Module 3 Performance. ● P0F03-00 - Hybrid/EV Battery Module 4 Performance. ● P0F04-00 - Hybrid/EV Battery Module 5 Performance. ● P0F05-00 - Hybrid/EV Battery Module 6 Performance. ● P0F06-00 - Hybrid/EV Battery Module 7 Performance. ● P0F07-00 - Hybrid/EV Battery Module 8 Performance. ● P0F08-00 - Hybrid/EV Battery Module 9 Performance. ● P0F09-00 - Hybrid/EV Battery Module 10 Performance. ● P0F0A-00 - Hybrid/EV Battery Module 11 Performance. ● P0F0B-00 - Hybrid/EV Battery Module 12 Performance. ● P0F0C-00 - Hybrid/EV Battery Module 13 Performance. ● P0CA6-00 - Hybrid/EV Battery Charging Current High. M08 FSAR-TSB-7132 -2- NOTE: If the following DTCs are present/active in the BPCM, Battery Pack replacement will be required. Guided Diagnostics will prompt you for the repair action if the diagnostic is present on the vehicle. ● P0ADB-00 - Hybrid/EV Battery Positive Contract
08-090-262026-03-13. Service bulletin. ELECTRICAL SYSTEM. Flash: Battery Pack Control Module (BPCM) Updates 11B3 Customers may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may SYMPTOM: exhibit/set one or more the following Diagnostic Trouble Codes (DTCs): ● P0AA7-00 - Hybrid/EV Battery Pack "A" Voltage Isolation Sensor. ● P1614-00 - ECU Reset/Recovery Occurred. ● B1A8A-00 - Multi-Module VIN Handshake Failure. ● P1CDB-00 - Hybrid/EV Wakeup Control 1 Output Circuit Short To Battery. ● P1E25-00 - EV Battery Failure Level 2. ● P0D10-00 - Hybrid/EV Battery Negative Contactor A Stuck Open. ● P0D09-00 - Hybrid/EV Battery Positive Contactor A Stuck Open. ● P0DE6-00 - Hybrid/EV Battery Pack Cell Voltage Low. NOTE: Active or stored. ● P1DAF - Incompatible Limp In Action Requested. NOTE: Active or stored. ● P1CDE-00 – Hybrid/EV Wakeup Control 2 Output Circuit Short to Ground. ● P1CDA-00 – Hybrid/EV Wakeup Control 1 Output Circuit/Open. ● U00C6-00 – Lost Communication With AIR Pressure Sensor. ● P0F00-00 - Hybrid/EV Battery Module 1 Performance. ● P0F01-00 - Hybrid/EV Battery Module 2 Performance. ● P0F02-00 - Hybrid/EV Battery Module 3 Performance. ● P0F03-00 - Hybrid/EV Battery Module 4 Performance. ● P0F04-00 - Hybrid/EV Battery Module 5 Performance. ● P0F05-00 - Hybrid/EV Battery Module 6 Performance. ● P0F06-00 - Hybrid/EV Battery Module 7 Performance. ● P0F07-00 - Hybrid/EV Battery Module 8 Performance. ● P0F08-00 - Hybrid/EV Battery Module 9 Performance. ● P0F09-00 - Hybrid/EV Battery Module 10 Performance. ● P0F0A-00 - Hybrid/EV Battery Module 11 Performance. ● P0F0B-00 - Hybrid/EV Battery Module 12 Performance. ● P0F0C-00 - Hybrid/EV Battery Module 13 Performance. ● P0CA6-00 - Hybrid/EV Battery Charging Current High. J08 FSAR-TSB-7107 -2- NOTE: If the following DTCs are present/active in the BPCM, Battery Pack replacement will be required. Guided Diagnostics will prompt you for the repair action if the diagnostic is present on the vehicle. ● P0ADB-00 - Hybrid/EV Battery Positive Contractor A Cont
08-089-262026-03-13. Service bulletin. ELECTRICAL SYSTEM. RSU With Additional Sleep Cycles for HV Battery Integrity Check Customers may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may SYMPTOM: exhibit/set one or more the following Diagnostic Trouble Codes (DTCs): ● P0AA7-00 - Hybrid/EV Battery Pack "A" Voltage Isolation Sensor. ● P1614-00 - ECU Reset/Recovery Occurred. ● B1A8A-00 - Multi-Module VIN Handshake Failure. ● P1CDB-00 - Hybrid/EV Wakeup Control 1 Output Circuit Short To Battery. ● P1E25-00 - EV Battery Failure Level 2. ● P0D10-00 - Hybrid/EV Battery Negative Contactor A Stuck Open. ● P0D09-00 - Hybrid/EV Battery Positive Contactor A Stuck Open. ● P0DE6-00 - Hybrid/EV Battery Pack Cell Voltage Low. NOTE: Active or stored. ● P1DAF - Incompatible Limp In Action Requested. NOTE: Active or stored. ● P1CDE-00 - Hybrid/EV Wakeup Control 2 Output Circuit Short to Ground. ● P1CDA-00 - Hybrid/EV Wakeup Control 1 Output Circuit/Open. ● U00C6-00 - Lost Communication With AIR Pressure Sensor. ● P0F00-00 - Hybrid/EV Battery Module 1 Performance. ● P0F01-00 - Hybrid/EV Battery Module 2 Performance. ● P0F02-00 - Hybrid/EV Battery Module 3 Performance. ● P0F03-00 - Hybrid/EV Battery Module 4 Performance. ● P0F04-00 - Hybrid/EV Battery Module 5 Performance. ● P0F05-00 - Hybrid/EV Battery Module 6 Performance. ● P0F06-00 - Hybrid/EV Battery Module 7 Performance. ● P0F07-00 - Hybrid/EV Battery Module 8 Performance. ● P0F08-00 - Hybrid/EV Battery Module 9 Performance. ● P0F09-00 - Hybrid/EV Battery Module 10 Performance. ● P0F0A-00 - Hybrid/EV Battery Module 11 Performance. ● P0F0B-00 - Hybrid/EV Battery Module 12 Performance. ● P0F0C-00 - Hybrid/EV Battery Module 13 Performance. ● P0CA6-00 - Hybrid/EV Battery Charging Current High. M08 FSAR-TSB-7115 -2- NOTE: If the following DTCs are present/active in the BPCM, Battery Pack replacement will be required. Guided Diagnostics will prompt you for the repair action if the diagnostic is present on the vehicle. ● P0ADB-00 - Hybrid/EV Battery Positive Contract
08-022-25 REV. D2025-12-23. Service bulletin. ELECTRICAL SYSTEM. Flash: Battery Pack Control Module (BPCM) Updates 11B3 Customers may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● **P1E25 - EV Battery Failure Level 2 ● P0D10 - Battery Charging System Negative Contactor "A" - Actuator Stuck Open ● P0D09 - Battery Charging System Positive Contactor "A" - Actuator Stuck Open** ● P0DE6 - Hybrid/EV Battery Pack Cell Voltage Low. NOTE: Active or stored. ● P1DAF - Incompatible Limp In Action Requested. NOTE: Active or stored. ● P1CDE - Hybrid/EV Wakeup Control 2 Output Circuit Short to Ground. ● P1CDA - Hybrid/EV Wakeup Control 1 Output Circuit/Open. ● U00C6 - Lost Communication With AIR Pressure Sensor. ● P0F00 - Hybrid/EV Battery Module 1 Performance. ● P0F01 - Hybrid/EV Battery Module 2 Performance. ● P0F02 - Hybrid/EV Battery Module 3 Performance. ● P0F03 - Hybrid/EV Battery Module 4 Performance. ● P0F04 - Hybrid/EV Battery Module 5 Performance. ● P0F05 - Hybrid/EV Battery Module 6 Performance. ● P0F06 - Hybrid/EV Battery Module 7 Performance. ● P0F07 - Hybrid/EV Battery Module 8 Performance. ● P0F08 - Hybrid/EV Battery Module 9 Performance. ● P0F09 - Hybrid/EV Battery Module 10 Performance. ● P0F0A - Hybrid/EV Battery Module 11 Performance. ● P0F0B - Hybrid/EV Battery Module 12 Performance. ● P0F0C - Hybrid/EV Battery Module 13 Performance. ● P0CA6-00 - Hybrid/EV Battery Charging Current High. NOTE: If the following DTCs are present/active in the BPCM, Battery Pack replacement will be required. Guided Diagnostics will prompt you for the repair action if the diagnostic is present on the vehicle. ● P0ADB-00 - Hybrid/EV Battery Positive Contractor A Control Circuit Low. ● P0AE2-00 - Hybrid/EV Battery Precharge Contactor Circuit Stuck Closed. ● P0AA1-00 - Hybrid/EV Battery Positive Contactor "A" Stuck Closed. ● P0FF8-00 - Hybrid/EV Battery Precharge Contactor Circuit "B" Stuck Closed. Customers may also comment on one or more of the following: ● **Will not be able to start the vehicle. ● A warning message will appear in the Instrument Panel Cluster (IPC) informing the driver to stop safely because the vehicle will be shutting down soon.** ● Wrench icon is illuminated on the IPC. ● Vehicle will not enter Drive Ready Mode. This bulletin also includes the following software enhancement: ● Bootloader update to prevent battery disconnect unit damage. ● Improvements in detecting pre-existing battery disconnect unit damage. ● Charging related enhancements that may lead to DTC P0CA6 falsely setting This bulletin involves reprogramming the IDCM, BPCM, MCP A, MCP B and the EVCU with the latest available software and then, if needed, performing a Wheel End Disconnect Position Learn routine.
08-071-25 REV. C2025-07-17. Service bulletin. ELECTRICAL SYSTEM. RSU With Additional Sleep Cycles for HV Battery Integrity Check -Customers may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set one or more the following Diagnostic Trouble Codes (DTCs): ● P0DE6 - Hybrid/EV Battery Pack Cell Voltage Low. NOTE: Active or stored. ● P1DAF - Incompatible Limp In Action Requested. NOTE: Active or stored. ● P1CDE – Hybrid/EV Wakeup Control 2 Output Circuit Short to Ground. ● P1CDA – Hybrid/EV Wakeup Control 1 Output Circuit/Open. ● U00C6 – Lost Communication With AIR Pressure Sensor. ● P0F00 - Hybrid/EV Battery Module 1 Performance. ● P0F01 - Hybrid/EV Battery Module 2 Performance. ● P0F02 - Hybrid/EV Battery Module 3 Performance. ● P0F03 - Hybrid/EV Battery Module 4 Performance. ● P0F04 - Hybrid/EV Battery Module 5 Performance. ● P0F05 - Hybrid/EV Battery Module 6 Performance. ● P0F06 - Hybrid/EV Battery Module 7 Performance. ● P0F07 - Hybrid/EV Battery Module 8 Performance. ● P0F08 - Hybrid/EV Battery Module 9 Performance. ● P0F09 - Hybrid/EV Battery Module 10 Performance. ● P0F0A - Hybrid/EV Battery Module 11 Performance. ● P0F0B - Hybrid/EV Battery Module 12 Performance. ● P0F0C - Hybrid/EV Battery Module 13 Performance. ● P0CA6-00 - Hybrid/EV Battery Charging Current High. NOTE: If the following DTCs are present/active in the BPCM, Battery Pack replacement will be required. Guided Diagnostics will prompt you for the repair action if the diagnostic is present on the vehicle. ● P0ADB-00 - Hybrid/EV Battery Positive Contractor A Control Circuit Low. ● P0AE2-00 - Hybrid/EV Battery Precharge Contactor Circuit Stuck Closed. ● P0AA1-00 - Hybrid/EV Battery Positive Contactor "A" Stuck Closed. ● P0FF8-00 - Hybrid/EV Battery Precharge Contactor Circuit "B" Stuck Closed. Customers may also comment on one or more of the following: ● Wrench icon is illuminated on the Instrument Panel Cluster (IPC). ● Vehicle will not enter Drive Ready Mode. This bulletin also includes the following software enhancements: ● Bootloader update to prevent battery disconnect unit damage. ● Improvements in detecting pre-existing battery disconnect unit damage. ● Charging related enhancements that may lead to DTC P0CA6 falsely setting This bulletin involves reprogramming the IDCM, BPCM, MCP A, MCP B and the EVCU with the latest available software and then, if needed, performing a Wheel End Disconnect Position Learn routine.
08-022-25 REV. C2025-07-17. Service bulletin. ELECTRICAL SYSTEM. Flash: Battery Pack Control Module (BPCM) Updates 11A2 Customers may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set one or more the following Diagnostic Trouble Codes (DTCs): ● P0DE6 - Hybrid/EV Battery Pack Cell Voltage Low. NOTE: Active or stored. ● P1DAF - Incompatible Limp In Action Requested. NOTE: Active or stored. ● P1CDE – Hybrid/EV Wakeup Control 2 Output Circuit Short to Ground. ● P1CDA – Hybrid/EV Wakeup Control 1 Output Circuit/Open. ● U00C6 – Lost Communication With AIR Pressure Sensor. ● P0F00 - Hybrid/EV Battery Module 1 Performance. ● P0F01 - Hybrid/EV Battery Module 2 Performance. ● P0F02 - Hybrid/EV Battery Module 3 Performance. ● P0F03 - Hybrid/EV Battery Module 4 Performance. ● P0F04 - Hybrid/EV Battery Module 5 Performance. ● P0F05 - Hybrid/EV Battery Module 6 Performance. ● P0F06 - Hybrid/EV Battery Module 7 Performance. ● P0F07 - Hybrid/EV Battery Module 8 Performance. ● P0F08 - Hybrid/EV Battery Module 9 Performance. ● P0F09 - Hybrid/EV Battery Module 10 Performance. ● P0F0A - Hybrid/EV Battery Module 11 Performance. ● P0F0B - Hybrid/EV Battery Module 12 Performance. ● P0F0C - Hybrid/EV Battery Module 13 Performance. ● P0CA6-00 - Hybrid/EV Battery Charging Current High. NOTE: If the following DTCs are present/active in the BPCM, Battery Pack replacement will be required. Guided Diagnostics will prompt you for the repair action if the diagnostic is present on the vehicle. ● P0ADB-00 - Hybrid/EV Battery Positive Contractor A Control Circuit Low. ● P0AE2-00 - Hybrid/EV Battery Precharge Contactor Circuit Stuck Closed P0AA1-00 - Hybrid/EV Battery Positive Contactor "A" Stuck Closed. ● P0FF8-00 - Hybrid/EV Battery Precharge Contactor Circuit "B" Stuck Closed. Customers may also comment on one or more of the following: ● Wrench icon is illuminated on the Instrument Panel Cluster (IPC). ● Vehicle will not enter Drive Ready Mode. This bulletin also includes the following software enhancements: ● Bootloader update to prevent battery disconnect unit damage. ● Improvements in detecting pre-existing battery disconnect unit damage. ● Charging related enhancements that may lead to DTC P0CA6 falsely setting. This bulletin involves reprogramming the IDCM, BPCM, MCP A, MCP B and the EVCU with the latest available software and then, if needed, performing a Wheel End Disconnect Position Learn routine.
08-022-25 REV. B2025-05-07. Service bulletin. ELECTRICAL SYSTEM. "Flash: Battery Pack Control Module (BPCM) Updates 11A1 Customers may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set one or more the following Diagnostic Trouble Codes (DTCs): ● **P0DE6 - Hybrid/EV Battery Pack Cell Voltage Low. NOTE: Active or stored. ● P1DAF - Incompatible Limp In Action Requested. NOTE: Active or stored. ● P1CDE – Hybrid/EV Wakeup Control 2 Output Circuit Short to Ground. ● P1CDA – Hybrid/EV Wakeup Control 1 Output Circuit/Open. ● U00C6 – Lost Communication With AIR Pressure Sensor. ● P0F00 - Hybrid/EV Battery Module 1 Performance. ● P0F01 - Hybrid/EV Battery Module 2 Performance. ● P0F02 - Hybrid/EV Battery Module 3 Performance. ● P0F03 - Hybrid/EV Battery Module 4 Performance. ● P0F04 - Hybrid/EV Battery Module 5 Performance. ● P0F05 - Hybrid/EV Battery Module 6 Performance. ● P0F06 - Hybrid/EV Battery Module 7 Performance. ● P0F07 - Hybrid/EV Battery Module 8 Performance. ● P0F08 - Hybrid/EV Battery Module 9 Performance. ● P0F09 - Hybrid/EV Battery Module 10 Performance. ● P0F0A - Hybrid/EV Battery Module 11 Performance. ● P0F0B - Hybrid/EV Battery Module 12 Performance. ● P0F0C - Hybrid/EV Battery Module 13 Performance.** ● P0CA6-00 - Hybrid/EV Battery Charging Current High. NOTE: If the following DTCs are present/active in the BPCM, Battery Pack replacement will be required. Guided Diagnostics will prompt you for the repair action if the diagnostic is present on the vehicle. ● P0ADB-00 - Hybrid/EV Battery Positive Contractor A Control Circuit Low. ● P0AE2-00 - Hybrid/EV Battery Precharge Contactor Circuit Stuck Closed. ● P0AA1-00 - Hybrid/EV Battery Positive Contactor ""A"" Stuck Closed. ● P0FF8-00 - Hybrid/EV Battery Precharge Contactor Circuit ""B"" Stuck Closed. Customers may also comment on one or more of the following: ● Wrench icon is illuminated on the Instrument Panel Cluster (IPC). ● Vehicle will not enter Drive Ready Mode. This bulletin also includes the following software enhancements: ● Bootloader update to prevent battery disconnect unit damage. ● Improvements in detecting pre-existing battery disconnect unit damage. ● Charging related enhancements that may lead to DTC P0CA6 falsely setting. This bulletin involves reprogramming the **IDCM,** BPCM, MCP A, MCP B and the EVCU with the latest available software and then, if needed, performing a Wheel End Disconnect Position Learn routine"
08-025-25 REV. B2025-05-07. Service bulletin. ELECTRICAL SYSTEM. "Flash: Battery Pack Control Module (BPCM) Updates 6A1 Customers may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● **P0DE6 - Hybrid/EV Battery Pack Cell Voltage Low. NOTE: Active or stored. ● P1DAF - Incompatible Limp In Action Requested. NOTE: Active or stored. ● P1CDE – Hybrid/EV Wakeup Control 2 Output Circuit Short to Ground. ● P1CDA – Hybrid/EV Wakeup Control 1 Output Circuit/Open. ● U00C6 – Lost Communication With AIR Pressure Sensor. ● P0F00 - Hybrid/EV Battery Module 1 Performance. ● P0F01 - Hybrid/EV Battery Module 2 Performance. ● P0F02 - Hybrid/EV Battery Module 3 Performance. ● P0F03 - Hybrid/EV Battery Module 4 Performance. ● P0F04 - Hybrid/EV Battery Module 5 Performance. ● P0F05 - Hybrid/EV Battery Module 6 Performance. ● P0F06 - Hybrid/EV Battery Module 7 Performance. ● P0F07 - Hybrid/EV Battery Module 8 Performance. ● P0F08 - Hybrid/EV Battery Module 9 Performance. ● P0F09 - Hybrid/EV Battery Module 10 Performance. ● P0F0A - Hybrid/EV Battery Module 11 Performance. ● P0F0B - Hybrid/EV Battery Module 12 Performance. ● P0F0C - Hybrid/EV Battery Module 13 Performance.** ● P0CA6-00 - Hybrid/EV Battery Charging Current High. NOTE: If the following DTCs are present/active in the BPCM, Battery Pack replacement will be required. Guided Diagnostics will prompt you for the repair action if the diagnostic is present on the vehicle. ● P0ADB-00 - Hybrid/EV Battery Positive Contractor A Control Circuit Low. ● P0AE2-00 - Hybrid/EV Battery Precharge Contactor Circuit Stuck Closed. ● P0AA1-00 - Hybrid/EV Battery Positive Contactor ""A"" Stuck Closed. ● P0FF8-00 - Hybrid/EV Battery Precharge Contactor Circuit ""B"" Stuck Closed. Customers may also comment on one or more of the following: ● Wrench icon is illuminated on the Instrument Panel Cluster (IPC). ● Vehicle will not enter Drive Ready Mode. This bulletin also includes the following software enhancements: ● Bootloader update to prevent battery disconnect unit damage. ● Improvements in detecting pre-existing battery disconnect unit damage. ● Charging related enhancements that may lead to DTC P0CA6 falsely setting. This bulletin involves reprogramming the **IDCM,** BPCM, MCP A, MCP B and the EVCU with the latest available software and then, if needed, performing a Wheel End Disconnect Position Learn routine"
08-071-25 REV. A2025-05-07. Service bulletin. ELECTRICAL SYSTEM. "RSU With Additional Sleep Cycles for HV Battery Integrity Check - Flash: Battery Pack Control Module (BPCM) Updates 11A1 Customers may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set one or more the following Diagnostic Trouble Codes (DTCs): ● P0DE6 - Hybrid/EV Battery Pack Cell Voltage Low. NOTE: Active or stored. ● P1DAF - Incompatible Limp In Action Requested. NOTE: Active or stored. ● P1CDE – Hybrid/EV Wakeup Control 2 Output Circuit Short to Ground. ● P1CDA – Hybrid/EV Wakeup Control 1 Output Circuit/Open. ● U00C6 – Lost Communication With AIR Pressure Sensor. ● P0F00 - Hybrid/EV Battery Module 1 Performance. ● P0F01 - Hybrid/EV Battery Module 2 Performance. ● P0F02 - Hybrid/EV Battery Module 3 Performance. ● P0F03 - Hybrid/EV Battery Module 4 Performance. ● P0F04 - Hybrid/EV Battery Module 5 Performance. ● P0F05 - Hybrid/EV Battery Module 6 Performance. ● P0F06 - Hybrid/EV Battery Module 7 Performance. ● P0F07 - Hybrid/EV Battery Module 8 Performance. ● P0F08 - Hybrid/EV Battery Module 9 Performance. ● P0F09 - Hybrid/EV Battery Module 10 Performance. ● P0F0A - Hybrid/EV Battery Module 11 Performance. ● P0F0B - Hybrid/EV Battery Module 12 Performance. ● P0F0C - Hybrid/EV Battery Module 13 Performance. ● P0CA6-00 - Hybrid/EV Battery Charging Current High. NOTE: If the following DTCs are present/active in the BPCM, Battery Pack replacement will be required. Guided Diagnostics will prompt you for the repair action if the diagnostic is present on the vehicle. ● P0ADB-00 - Hybrid/EV Battery Positive Contractor A Control Circuit Low. ● P0AE2-00 - Hybrid/EV Battery Precharge Contactor Circuit Stuck Closed. ● P0AA1-00 - Hybrid/EV Battery Positive Contactor ""A"" Stuck Closed. ● P0FF8-00 - Hybrid/EV Battery Precharge Contactor Circuit ""B"" Stuck Closed. Customers may also comment on one or more of the following: ● Wrench icon is illuminated on the Instrument Panel Cluster (IPC). ● Vehicle will not enter Drive Ready Mode. This bulletin also includes the following software enhancements: ● Bootloader update to prevent battery disconnect unit damage. ● Improvements in detecting pre-existing battery disconnect unit damage. ● Charging related enhancements that may lead to DTC P0CA6 falsely setting. This bulletin involves reprogramming the IDCM, BPCM, MCP A, MCP B and the EVCU with the latest available software and then, if needed, performing a Wheel End Disconnect Position Learn routine"
08-071-25 REV. B2025-05-06. Service bulletin. ELECTRICAL SYSTEM. "RSU With Additional Sleep Cycles for HV Battery Integrity Check - Flash: Battery Pack Control Module (BPCM) Updates 11A1 Customers may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set one or more the following Diagnostic Trouble Codes (DTCs): ● P0DE6 - Hybrid/EV Battery Pack Cell Voltage Low. NOTE: Active or stored. ● P1DAF - Incompatible Limp In Action Requested. NOTE: Active or stored. ● P1CDE – Hybrid/EV Wakeup Control 2 Output Circuit Short to Ground. ● P1CDA – Hybrid/EV Wakeup Control 1 Output Circuit/Open. ● U00C6 – Lost Communication With AIR Pressure Sensor. ● P0F00 - Hybrid/EV Battery Module 1 Performance. ● P0F01 - Hybrid/EV Battery Module 2 Performance. ● P0F02 - Hybrid/EV Battery Module 3 Performance. ● P0F03 - Hybrid/EV Battery Module 4 Performance. ● P0F04 - Hybrid/EV Battery Module 5 Performance. ● P0F05 - Hybrid/EV Battery Module 6 Performance. ● P0F06 - Hybrid/EV Battery Module 7 Performance. ● P0F07 - Hybrid/EV Battery Module 8 Performance. ● P0F08 - Hybrid/EV Battery Module 9 Performance. ● P0F09 - Hybrid/EV Battery Module 10 Performance. ● P0F0A - Hybrid/EV Battery Module 11 Performance. ● P0F0B - Hybrid/EV Battery Module 12 Performance. ● P0F0C - Hybrid/EV Battery Module 13 Performance. ● P0CA6-00 - Hybrid/EV Battery Charging Current High. NOTE: If the following DTCs are present/active in the BPCM, Battery Pack replacement will be required. Guided Diagnostics will prompt you for the repair action if the diagnostic is present on the vehicle. ● P0ADB-00 - Hybrid/EV Battery Positive Contractor A Control Circuit Low. ● P0AE2-00 - Hybrid/EV Battery Precharge Contactor Circuit Stuck Closed. ● P0AA1-00 - Hybrid/EV Battery Positive Contactor ""A"" Stuck Closed. ● P0FF8-00 - Hybrid/EV Battery Precharge Contactor Circuit ""B"" Stuck Closed Customers may also comment on one or more of the following: ● Wrench icon is illuminated on the Instrument Panel Cluster (IPC). ● Vehicle will not enter Drive Ready Mode. This bulletin also includes the following software enhancements: ● Bootloader update to prevent battery disconnect unit damage. ● Improvements in detecting pre-existing battery disconnect unit damage. ● Charging related enhancements that may lead to DTC P0CA6 falsely setting"
08-071-252025-03-25. Service bulletin. ELECTRICAL SYSTEM. "Flash: Battery Pack Control Module (BPCM) Updates Customers may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set one or more the following Diagnostic Trouble Codes (DTCs): ● P167B-00 - Controlled System Shutdown. ● P0CA6-00 - Hybrid/EV Battery Charging Current High. NOTE: If the following DTCs are present/active in the BPCM, Battery Pack replacement will be required. Guided Diagnostics will prompt you for the repair action if the diagnostic is present on the vehicle. ● P0AA1-00 - Hybrid/EV Battery Positive Contactor ""A"" Stuck Closed. ● P0FF8-00 - Hybrid/EV Battery Precharge Contactor Circuit ""B"" Stuck Closed. ● P0ADB-00 - Hybrid/EV Battery Positive Contactor ""A"" Control Circuit Low. ● P0AE2-00 - Hybrid/EV Battery Contactor Circuit Stuck Closed. Customers may also comment on one or more of the following: ● Wrench icon is illuminated on the Instrument Panel Cluster (IPC). ● Vehicle will not enter Drive Ready Mode. ● Battery range incorrect. This bulletin also includes the following software enhancements: ● Bootloader update to prevent battery disconnect unit damage. ● Improvements in detecting pre-existing battery disconnect unit damage. ● Charging related enhancements that may lead to DTC P0CA6 falsely setting. ● Improved battery State of Charge (SoC) accuracy in off-nominal conditions. This bulletin involves reprogramming the BPCM, MCP A, MCP B and the EVCU with the latest available software and then, if needed, performing a Wheel End Disconnect Position Learn routine."
08-022-252025-02-04. Service bulletin. ELECTRICAL SYSTEM. "Flash: Battery Pack Control Module (BPCM) Updates Customers may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0ADB-00 - Hybrid/EV Battery Positive Contractor A Control Circuit Low. ● P0AE2-00 - Hybrid/EV Battery Precharge Contactor Circuit Stuck Closed. Customers may also comment on one or more of the following: ● Wrench icon is illuminated on the Instrument Panel Cluster (IPC). ● Vehicle will not enter Drive Ready Mode. ● Battery range incorrect. This bulletin also includes the following software enhancement: ● Improved battery State of Charge (SoC) accuracy in off-nominal conditions. This bulletin involves reprogramming the BPCM, MCP A, MCP B and the EVCU with the latest available software and then, if needed, performing a Wheel End Disconnect Position Learn routine"
08-267-242025-01-03. Service bulletin. ELECTRICAL SYSTEM. "Flash: Battery Pack Control Module (BPCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set the following Diagnostic Trouble Code (DTC): ● P0ADB-00 - Hybrid/EV Battery Positive Contractor A Control Circuit Low. ● P0AE2-00 - Hybrid/EV Battery Precharge Contactor Circuit Stuck Closed. Customers may also comment on one or more of the following: ● Wrench icon is illuminated on the Instrument Panel Cluster (IPC). ● Vehicle will not enter Drive Ready Mode. ● Battery range incorrect. This bulletin also includes the following software enhancement: ● Improved battery State of Charge (SoC) accuracy This bulletin involves reprogramming the BPCM, MCP A, MCP B and the EVCU with the latest available software and then, if needed, performing a Wheel End Disconnect Position Learn routine."

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.