Service bulletins for the 2014 Dodge Challenger
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
200 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
| 18-034-14 REV. A | 2018-06-18. Service bulletin. ENGINE. P0520- Engine Oil Pressure Sensor Circuit This bulletin involves replacing the oil pressure sensor with a revised part. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that the following Diagnostic Trouble Code (DTC) has been set: P0520 - Engine Oil Pressure Sensor Circuit |
|---|---|
| Z5091195A$ | 2018-06-11. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM); EQUIPMENT; EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.; EQUIPMENT:ELECTRICAL. RES / RHA / REB radio that supports Bluetooth and Hands-Free For issues with Bluetooth, Hands-Free Calling, and/or Voice Commands, DO NOT replace the radio. Diagnose the Hands-Free Module system (also called the Telematics Module). The Telematics Module (and associated components) is the system responsible for these features. A power cycle may be required for the hands-free module for proper diagnosis.~ Please reference; 8T - Navigation/Telecommunication Diagnosis and Testing (DIAGNOSIS AND TESTING - HANDS FREE PHONE) |
| 18-094-16 | 2018-06-11. Service bulletin. EXTERIOR LIGHTING; BACK OVER PREVENTION; EQUIPMENT; POWER TRAIN; ELECTRICAL SYSTEM. Flash: Powertrain Diagnostic And System Enhancements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. A small number of customers may experience one or more of the following conditions: With the cluster set on metric units, they are unable to accurately increase or decrease the cruise control set speed using the resume or set buttons. Instead of changing vehicle speed by 1 kph when pressing the buttons, the vehicle speed will increase approximately 1.6 kph. Potential gear hunting during cruise operation at lower vehicle speeds 40-64 kph (25-40 mph). In addition, a small number of customers may experience certain symptoms/conditions or a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that the following Diagnostic Trouble Codes have been set: P1115 - General Temperature Rationality. P0456 - EVAP System Small Leak. P0441 - EVAP Purge System Performance. P2610 - PCM Internal Engine Off Timer Performance. P0300 - Multiple Cylinder Misfire. P0301 - Cylinder 1 Misfire. P0302 - Cylinder 2 Misfire. P0303 - Cylinder 3 Misfire. · P0304 - Cylinder 4 Misfire. · P0305 - Cylinder 5 Misfire. · P0306 - Cylinder 6 Misfire. · P0307 - Cylinder 7 Misfire. · P0308 - Cylinder 8 Misfire. · P0335 - Crankshaft Position Sensor Circuit. · P0122 - Throttle Position Sensor 1 Circuit Low. · P0123 - Throttle Position Sensor 1 Circuit High. · P0222 - Throttle Position Sensor 2 Circuit Low. · P0223 - Throttle Position Sensor 2 Circuit High. · P2299 - Brake Pedal Position / Accelerator Pedal Position Incompatible.** · P2096 - Downstream Fuel Trim System 1 Lean. (LC vehicles with Sales Code ESH with a manual transmission (Sales Code DEC). · P2097 - Downstream Fuel Trim System 1 Rich. (LC vehicles with Sales Code ESH with a manual transmission (Sales Code DEC). · P2098 - Downstream Fuel Trim System 2 Lean. (LC vehicles with Sales Code ESH with a ma |
| 9003694 | 2018-06-11. Service bulletin. ENGINE AND ENGINE COOLING. Oil Pump Assembly If error code P06DD present on any Pentastar V6 application, please inspect oil pump for relief valve failure. See photo attached. If valve is found out of place please call Bob Jackson (248) 944-0466 bob.jackson@fcagroup.com, or Joe Lovell (734) 309-6467 joe.lovell@fcagroup.com before proceeding. If unable to reach after 15 minutes record the following information and proceed with oil pump replacement and hold part for return to FCA via Fastrack system |
| 9003681 | 2018-06-11. Service bulletin. SEAT BELTS. Restraints Information Sheet (I-Sheet) has been added to Star Parts. Print I-Sheet for technician use. |
| 9003687 | 2018-06-11. Service bulletin. SEAT BELTS. Restraints Remove I-Sheet from packaging. Correct information sheet (I-Sheet) has been added to Star Parts. Print I-Sheet for technician use. |
| 68277402A | 2018-06-11. Service bulletin. VEHICLE SPEED CONTROL:CRUISE CONTROL. Adaptive Cruise Control Sensor 1) If you are replacing this part due to the cluster displaying Clean Radar Sensor in Front of Vehicle or DTC C1266 ACC Sensor Blinded, please verify that there is no blockage in front of the sensor. Blockage can occur from mud, ice, snow, front end damage, bracket damage, the sensor not attached to the bracket properly or an aftermarket fascia installed. This fault can occur intermittently in muddy or icy/snowy conditions and is considered normal operation. Under some circumstances, a misaligned sensor can also cause the C1266 DTC, please complete an alignment procedure. No replacement is required.~ 2) If you are replacing this part due to the cluster displaying ?ACC/FCW Unavailable Service Required?, please check the DTC fault codes. This will indicate which module needs to be serviced (TCM, PCM, ESP/ABS, etc). This fault is not due to the ACC Sensor. No sensor replacement is required.~ 3) If you have fault code DTC C125E ACC Sensor Adjustment Required, please verify that the radar sensor is fully seated in the clips and there is no damage (if clips are damaged on a 2013 or earlier vehicle, order P/N 68085813A$, otherwise please replace the module), please verify there is no blockage to the sensor due to mud, ice, snow, front end damage, bracket damage or the sensor not attached to the bracket properly. Perform the Vertical Alignment and the Electronic Horizontal Alignments procedure as stated in the service manual. Please note, if the horizontal alignment procedure will not complete, check the vertical alignment and confirm that the sensor is seated properly. Rerun the horizontal alignment procedure. No sensor replacement is required. **Hints for running Horizontal Alignment procedure: A) Verify speed is between 45 and 75 mph, B) verify the road is relatively straight with signs, poles, guard rails, etc C) Do not tail a vehicle too closely this inhibits the learning procedure |
| 68105583A | 2018-06-11. Service bulletin. ENGINE AND ENGINE COOLING. Pentastar Oil Filter Adapter: Before replacing this part, please call any one of the following people. Engineering is seeking information regarding this part.~ Dye must be used to determine where the leak is coming from before replacing. Also please check the recently updated Service Bulletin Number 09-008-15. ~ First: Nick Morand Cell (248) 410-8078 - Nick.morand@fcagroup.com Second: Bob Jackson Cell (248) 944-0466 - bob.jackson@fcagroup.com Third: Joe Lovell Cell (734 309-6467 - joe.lovell@fcagroup.com If a response is not received within 15 mins, then proceed with the necessary repair.~ |
| 08-112-14 | 2018-06-11. Service bulletin. EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.. Hands Free Feature Inoperative This bulletin involves updating the Hands Free Module (HFM) software. The customer may notice that the hands free feature (Bluetooth) does not work. On further inspection Diagnostic Trouble Code (DTC), U0197 - Lost Communication With Hands Free Phone Module may be found. |
| 23-026-14 REV. A | 2018-06-11. Service bulletin. STRUCTURE:BODY:DOOR. Wind Noise At The Left And/Or Right Door This bulletin involves repositioning the outer door mounted window seal flag. The customer may describe a wind noise at the left and/or right door. |
| 18-037-14 REV. B | 2018-06-11. Service bulletin. POWER TRAIN. Flash: 6.4L Powertrain Diagnostic And System Improvements For MIL Illumination This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that the following Diagnostic Trouble Code has been set: * P2096 - Downstream Fuel Trim System 1 Lean. * P2097 - Downstream Fuel Trim System 1 Rich. * P2098 - Downstream Fuel Trim System 2 Lean. * P2099 - Downstream Fuel Trim System 2 Rich. * P0300 - Multiple Cylinder Misfire (set during engine warm-up) |
| 08-086-14 REV. A | 2018-06-11. Service bulletin. EQUIPMENT. RBZ Or RHB Radio Software Enhancements This bulletin involves upgrading the software on the RBZ or RHB Radio. The customer may experience one or more of the following. When changing the language on the radio, the navigation may still display English. Help prevent navigation lockup. Ghost image of the vehicle?s brand logo on the display screen. Digital photos loaded onto the hard drive intermittently get lost. Sirius audio pop on power up. HFM audio pop on power up. HFM Mode resume with no information.SYMPTOM/CONDITION FOR RHB RADIOS ONLY: Trip planner does not save a route after is was created. Route guidance does not activate after the vehicle shuts down. Longitude entry does not allow enough digits. CD/DVD will not play. Navigation accept screen will not clear. Navigation shows ?acquiring signal? for an extended period of time. New navigation graphics. |
| 18-054-14 | 2018-06-11. Service bulletin. ENGINE AND ENGINE COOLING. Intermittent Extended Crank, Long Crank Time. This bulletin involves inspecting the Bank 1 Camshaft Position Sensor serial number and if necessary, replacing the sensor. A small number of customers may experience an intermittent 1 to 5 second extended crank condition when starting their vehicle. No DTCs will be present when this occurs. |
| 08-086-14 | 2018-06-11. Service bulletin. EQUIPMENT. RBZ Or RHB Radio Software Enhancements This bulletin involves upgrading the software on the RBZ or RHB Radio. The customer may experience one or more of the following. ? When changing the language on the radio, the navigation may still display English. ? Help prevent navigation lockup. ? Ghost image of the vehicle?s brand logo on the display screen. ? Digital photos loaded onto the hard drive intermittently get lost. ? CD/DVD will not play (RHB only). ? Navigation accept screen will not clear (RHB only). ? Navigation shows ?acquiring signal? for an extended period of time (RHB only). ? New navigation graphics (RHB only). ? Sirius audio pop on power up. ? HFM audio pop on power up. ? HFM Mode resume with no information. ? Trip planner does not save a route after is was created (RHB only). ? Route guidance does not activate after the vehicle shuts down (RHB only). ? Longitude entry does not allow enough digits (RHB only). |
| 23-026-14 | 2018-06-11. Service bulletin. VISIBILITY:GLASS, SIDE/REAR. Wind Noise At The Left And/Or Right Door This bulletin involves repositioning the outer door mounted window seal flag. The customer may describe a wind noise at the left and/or right door. |
| 18-034-14 | 2018-06-11. Service bulletin. ENGINE AND ENGINE COOLING. P0520- Engine Oil Pressure Sensor Circuit This bulletin involves replacing the oil pressure sensor with a revised part. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that the following Diagnostic Trouble Code (DTC) has been set: P0520 - Engine Oil Pressure Sensor Circuit |
| 19-002-14 REV. A | 2018-06-11. Service bulletin. STEERING. Steering Column Squeak / Moan While Turning Wheel This bulletin involves removing/installing the steering column, removing/installing the bulkhead pass through boot, removing the wiper seal, and applying lubricant to the intermediate shaft bearing sleeve. Customer may describe a squeak and/or moan noise while turning the steering wheel. Noise can be heard both while vehicle is stationary or while driving. Noise is typically more noticeable during cold temperatures and may go away when vehicle warms up. |
| 18-027-14 | 2018-06-11. Service bulletin. ELECTRICAL SYSTEM. Flash: Powertrain System Improvements/Enhancements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. The following powertrain system improvements/enhancements are included in this software release: Corrected a generic scan tool display issue regarding Mode 6 data accuracy. |
| 9002503 | 2018-06-11. Service bulletin. EQUIPMENT; POWER TRAIN; BACK OVER PREVENTION; VISIBILITY; SUSPENSION; ELECTRICAL SYSTEM; FUEL SYSTEM, GASOLINE. Part Description: RHR Radio Issue Description: Issue 1: While performing RHR radio reflash (software update), on rare occasions, the flash can fail to properly update the radio resulting in the radio running in Emergency IFS mode. This error condition can occur due to interrupting the software update, background radio operations interfering with the reflash process, etc. The radio will reboot, but with limited functionality (examples may include but are not limited to: NAV, Voice Recognition, Bluetooth, or AUX jack are inop, no available space shown on HDD, etc.). The radio can still be properly updated by simply reinserting the software update disc and performing the reflash procedure again. To assist in the verification that the radio is running Emergency IFS perform the following:~ 1. Power on radio~2. Press MENU H/K~3. Press System Setup S/K~4. Press Manage HDD S/K~5. Press Display Available Space on HDD S/K~6. When running Emergency IFS, all items under Used, Available, and Capacity report as dashes~ Issue 2: If you are having troubles connecting a phone or a MP3 player, try removing the battery on the device and then going through the pairing/connection procedure again. If you cannot remove the battery on the device, perform a reboot. Each manufacturer has a different series of buttons to hold down to perform a reboot. If the problem still persists, try the device on another like vehicle with the same radio. If you are having the same connection issues on another like vehicle, the device may be faulty or it may not be compatible with the RHR radio. Go to www.chrysler.com/hostb/crossbrand/owners/en and click on ?Bluetooth Phone Compatibility Test Results? link for a list of phones that are compatible. For MP3 players and media storage devices, only .wma, .aac, .mp3, .sacd, .jpeg & .jpg files are supported. Remove all other file types and reevaluate the concern. ~ Issue 3: If upgrading a vehicle from a low line radio that has factory installed UConnect |
| 08-024-14 | 2018-05-21. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.. RHW RHP Radio Software Enhancements This bulletin involves upgrading the software on the RHW or RHP Radio. The customer may experience one or more of the following conditions. Navigation voice prompt is now announced near maneuvers such as exit ramps. Radio freeze when playing large number of .M4A or .WMA files,and recovers with ignition cycle. Battery signal strength display is not displayed into the radio screen (with iPhone 5). Traffic Announcement and Voice Recognition share the same volume control. Traffic Announcement volume drops after phone calls. Mismatch in the ?Distance to next turn? between the radio and EVIC displays. German translations are incorrect. Radio reset when copying certain .MP3 files from USB flash drive to the radio. Radio stations info is not correct into the right side of the radio display (radio menu). Radio mute issue in tuner mode. Preset loss during/after AF Switching. Erratic alternate frequency switching. Bluetooth phone muting during European traffic announcement. Enhancements to the loss of preset condition. Lost channel presets, home addresses, address book entries & Travel Link favorites. Not able to change default country and state then route. Unable to load .jpeg files onto hard drive to display on touch screen. Vehicle with Start/Stop feature, the screen will go black when the engine turns off at a stop. (International only). Cancel key inoperative after pressing the international button. iPhone 4 dial not possible after second call. Devices button disabled in VES menu. Unable to route to a recent route after a map update. Duplicate phone numbers in popup after pressing the international button. During active call and on hold, DIAL button should be displayed (not ?TONE? button). International button not visible. Point of Interest (POI) Search enhancements. Devices button wrongly labeled as DVD using the remote DVD player. iPod, track selection enhancements. |
| 18-015-14 | 2018-05-21. Service bulletin. POWER TRAIN; ENGINE AND ENGINE COOLING. Flash: Malfunction Indicator Lamp (MIL) Illumination. Includes Various Driveability Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that the following Diagnostic Trouble Codes have been set: P0300 - Multiple Cylinder MisfireThe P0300 improvement only applies to vehicles using a block heater in ambient temperatures greater than -20°F(-29°C). P0606 - Internal Control Processor P219A - Air-Fuel Ratio Cylinder Imbalance Bank 1This release also contains the following improvements: (applies only to LC vehicles) Accuracy improvements for the Automatic Oil Change Indicator (AOCI) system. |
| 19-002-14 | 2018-05-21. Service bulletin. VISIBILITY; POWER TRAIN; STEERING. Steering Column Squeak / Moan While Turning Wheel This bulletin involves removing/installing the steering column, removing/installing the bulkhead pass through boot, removing the wiper seal, and applying lubricant to the intermediate shaft bearing sleeve. Customer may describe a squeak and/or moan noise while turning the steering wheel. Noise can be heard both while vehicle is stationary or while driving. Noise is typically more noticeable during cold temperatures and may go away when vehicle warms up. |
| 18-088-16 REV. A | 2018-05-07. Service bulletin. ENGINE AND ENGINE COOLING; ELECTRICAL SYSTEM; POWER TRAIN. Flash: Powertrain Diagnostic And System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination or a less than desired powertrain response when operating their vehicles in high ambient temperatures. Upon further investigation the technician may find one or more of the following DTCs have been set: · **P0335 - Crankshaft Position Sensor Circuit. · P2610 - PCM Internal Engine Off Timer Performance. · P0456 - EVAP System Small Leak (Sales Code ERB).** · U0140 - Lost Communication With Body Control Module - (BCM) (VF, LD, LX vehicles only). · P0606 - Internal Control Processor. |
| 18-088-16 REV. A | 2018-02-21. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Flash: Powertrain Diagnostic And System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination or a less than desired powertrain response when operating their vehicles in high ambient temperatures. Upon further investigation the technician may find one or more of the following DTCs have been set: · **P0335 - Crankshaft Position Sensor Circuit. · P2610 - PCM Internal Engine Off Timer Performance. · P0456 - EVAP System Small Leak (Sales Code ERB).** · U0140 - Lost Communication With Body Control Module - (BCM) (VF, LD, LX vehicles only). · P0606 - Internal Control Processor. |
| 9002519 | 2018-02-21. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. 82212076, 82203694 - Fabric Cleaner This "fabric cleaner" is not intended for sale in California, the otc states (Connecticut, Delaware, Massachusetts, Maine, New Hampshire, New Jersey, New York, Pennsylvania, Virginia, and Washington dc), and some ladco states (Illinois, Michigan, and Ohio). Mopar offers an alternative product (82213192) which is a water based product approved for sale in the aforementioned states.~ ~ Please inform the customer & your prep dept that spraying excessive amounts of the fabric protector on load floors will result in the breaking down of the adhesive (glue) that is used to create the bond between the fabric (carpet) and the load floor. This will apply to any vehicles equipped with rear load floors such as WK, WD, PM, MK, KA, KK. The carpet will appear to be loose, wrinkly, or bunch up~ |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.