WenmarOpen by Wenmar Pro

Service bulletins for the 2019 Chrysler 300

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

270 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

Only bulletins with component: Transmission and driveline are shown. Show all

Bulletins, newest first
S26210000042026-10-07. Service bulletin. POWER TRAIN. The Customer May Complain About a Popping Noise, Grinding Noise, or an Intermittent No Reverse or Forward Transmission Engagement. The Tech May Find Damaged and/or Worn Transmission Output Shaft Splines (850RE Transmission Only)
S2621000003 REV.A2026-03-18. Service bulletin. POWER TRAIN. The vehicle will exhibit a service transmission/check engine warning indicator for the following transmission models: 845RE, 8HP45, 850RE, 8HP50, 8HP70, 8HP75, 8HP75-PHEV, 8HP75-LCV, 8HP90, 8HP95. Transmissions may exhibit the following diagnostic codes: P07E4, P1DB2, P0716, P1B14, P0733, P1D90, P1DB7, P1B13.
18-089-242025-01-03. Service bulletin. POWER TRAIN. "Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● **P0420 - Catalyst System Efficiency Below Threshold Bank 1. ● P0430 - Catalyst System Efficiency Below Threshold Bank 2.** ● P0456 - EVAP System Small Leak. NOTE: If DTC P0456 is present use the wiTECH Small Leak Verification test (SLVT) to determine if a leak is present in the system. This bulletin involves reprogramming the PCM with the latest available software."
995002024-07-31. Other. POWER TRAIN. CARRIER – PLANETARY & SHAFT KIT - OUTPUT
91003442024-06-04. Service bulletin. POWER TRAIN. "VALVE BODY & CONTROL UNIT Transmission Ensure clutch pressure check has been completed and documented prior to valve body replacement."
S22210000032024-01-08. Service bulletin. POWER TRAIN. 8-Speed Transmission, Additional Transmission Fluid Leak Inspection/Repair Guidelines.
S22210000032023-10-30. Service bulletin. POWER TRAIN. 8-Speed Transmission, Additional Transmission Fluid Leak Inspection/Repair Guidelines.
S18080001522023-04-17. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). CEL (Check Engine Lamp) Illuminates, Recent PCM Replace or Flash Update Performed, Diagnostic Trouble Codes (DTCs) P057B Brake Pedal Position Sensor Circuit Performance, P1572 Brake Pedal Stuck, C0042-54 Brake Pedal Missing Calibration
S22210000032023-01-09. Service bulletin. POWER TRAIN. 8-Speed Transmission, Additional Transmission Fluid Leak Inspection/Repair Guidelines.
S20180000082022-10-17. Service bulletin. POWER TRAIN; ELECTRICAL SYSTEM. Engine Surge Feel and/or Diagnostic Trouble Code P0299 ? Turbo Underboost Condition After Updating The Powertrain Control Module (PCM) Software. (ETL, ETM, ETN Engines)
S22080000732022-10-17. Service bulletin. POWER TRAIN. No Start, After Flash And Or PCM Replace, DTC P0513 Invalid Skim Key Setting
08054212022-09-26. Service bulletin. ELECTRICAL SYSTEM; EXTERIOR LIGHTING; POWER TRAIN. High Beam Headlamps Flicker This bulletin involves installing jumper wires from the Power Distribution Center(PDC) to the headlamp connectors. The technician may find one or more of the following Diagnostic Trouble Codes (DTCs).B1632-15 - Left High Beam Control-Circuit Short To Battery Or Open. B1636-11 - Right High Beam Control-Circuit Short To Ground. In addition the customer may describe the following:High beam headlamps flicker in cold weather. High beams lamps not working properly in cold weather.
S18210000012022-09-26. Service bulletin. POWER TRAIN. Gear Ratio DTC?s, Transmission Shift Concerns, Does Not Shift At Times, Shudders
90040092022-09-26. Service bulletin. POWER TRAIN. Transmission Kit with Torque Converter 1. All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.
08-054-212021-05-24. Service bulletin. ELECTRICAL SYSTEM; EXTERIOR LIGHTING; POWER TRAIN. High Beam Headlamps Flicker This bulletin involves installing jumper wires from the Power Distribution Center(PDC) to the headlamp connectors. The technician may find one or more of the following Diagnostic Trouble Codes (DTCs).B1632-15 - Left High Beam Control-Circuit Short To Battery Or Open. B1636-11 - Right High Beam Control-Circuit Short To Ground. In addition the customer may describe the following:High beam headlamps flicker in cold weather. High beams lamps not working properly in cold weather.
S2008000113 Rev.2021-05-24. Service bulletin. POWER TRAIN. No Start Intermittently, Vehicle Requires Multiple Keyless Push To Start Attempts To Start Vehicle, Intermittent Key Not Detected Message
18-108-202021-03-01. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); ELECTRICAL SYSTEM. Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs):P0420 - Catalyst System Efficiency Below Threshold Bank 1 P0430 - Catalyst System Efficiency Below Threshold Bank 2. Customers may describe the following:Hearing a pre-detonation noise (Spark Knock) sound in the engine during acceleration.
S20180000082020-07-27. Service bulletin. POWER TRAIN. Engine Surge Feel and/or Diagnostic Trouble Code P0299 ? Turbo Underboost Condition After Updating The Powertrain Control Module (PCM) Software. (ETL, ETM, ETN Engines)
18-038-202020-05-26. Service bulletin. POWER TRAIN; ELECTRICAL SYSTEM. Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that the followingDiagnostic Trouble Code (DTC) has been set:P0456 - EVAP System Small Leak.If DTC P0456 is present use the wiTECH Small Leak Verification Test (SLVT) to determine if a leak is present in the system. Customers may also experience the following:Noise heard from the drivetrain while stationary and vehicle is in Sport/Track modes.
21-031-202020-05-26. Service bulletin. POWER TRAIN; ELECTRICAL SYSTEM. Flash: Transmission Control Module (TCM) Updates This bulletin involves reprogramming the TCM with the latest available software. Customers may describe the following: After a cold start (in rare instances), the vehicle can be shifted intodrive and the vehicle will not move. Shifting to park and back to drive rectifies the situation.
90037632020-01-21. Service bulletin. POWER TRAIN. Transfer case seal, Transmission Output Seal If vehicle has a fluid leak between the transfer case and the transmission on an AWD vehicle and it has been determined that the transfer case is leaking from the vent hole, don't replace the input seal. The vehicle can be repaired by: Transfer Case replace - 68214750A$ 3.6 Pentastar 68214751A$ 5.7 Hemi Replace Front Case Half - 68101734A$ 3.6 Pentastar 68101734A$ 5.7 Hemi Note: The transfer case oil already has dye in it so leak confirmation with a black light can be achieved.
18-085-192019-12-02. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with updated software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that the following Diagnostic Trouble Code (DTC) has been set: P0456 - EVAP System Small Leak.If DTC P0456 is present use the wiTECH Small Leak Verification test (SLVT) to determine if a leak is present in the system.Perform this software flash only on vehicles with less than 57 miles on the odometer.
18-077-192019-12-02. Service bulletin. ELECTRICAL SYSTEM; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that the following Diagnostic Trouble Code (DTC) has been set: P0456 - EVAP System Small Leak.
90041502019-12-02. Service bulletin. FUEL SYSTEM, GASOLINE; POWER TRAIN. SEAL, Input If looking to replace stubshaft due to ATX fluid leaking, do not replace PTU seals. None of the seals from the PTU side will need to be replaced whenever the ATX stubshaft is replaced, even though V-seal (68408748A$) is in direct contact with the stubshaft, it will not avoid grease/oil leakage from transmission side. PTU V-seals are intended to act as a dust cover for stubshaft - PTU input shaft spline interface. PTU Input shaft seal (68408749A$) is intended to hold PTU oil and debris ingress; it should be replaced only if the fluid leakage is confirmed to be PTU oil and not ATX trans. fluid.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.