WenmarOpen by Wenmar Pro

Service bulletins for the 2014 Chevrolet Volt

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

1655 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Only bulletins with component: Engine are shown. Show all

Bulletins, newest first
PIP4843H2017-08-15. Service bulletin. ELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING; ELECTRICAL SYSTEM:ALTERNATOR/GENERATOR/REGULATOR. This Preliminary Information communication advises the technician that effective November 1st, 2010 the Drive Motor Generator Control Module part number 24266807 and 24279524 will be placed on restriction through the General Motors Technical Assistance Center. Dealer will need to contact General Motors Technical Assistance Center for further assistance.
PIP4870B2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE; ELECTRICAL SYSTEM:12V/24V/48V BATTERY. This Preliminary Information communication provides information to the technician about vehicles that may have a engine noise is sometimes louder than expected. Also will explain the known normal and abnormal reasons why the engine may be louder. When the vehicle speed is between 25-50 miles per hour the road noise does not mask the engine noise this is considered normal. When the vehicle is first started for the day the system will perform a catalyst preconditioning for about a minute. At this time the engine will seem louder than normal, this is normal. At times the engine often runs at wide open throttle, but at a reduced speed. This sound is uncharacteristic of a four-cylinder engine in a traditional sedan, but is a characteristic of an extended range electric vehicle such as the Chevrolet Volt. Technician will be able to inspect for abnormal induction ground-out conditions. These locations should be checked lower rubber isolator on air box not installed correctly or missing, upper induction resonator cover not installed properly, refrigerant line not bolted to engine support bracket, and throttle body contacting coolant pipes behind it. Abnormal exhaust ground-out conditions should also be inspected. These locations are at the exhaust clamp rearward of the second catalytic converter is contacting the battery heat shield, exhaust resonator underbody is contacting the heat shield. Repair any abnormal issue found.
PIP4880D2017-08-15. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; ELECTRICAL SYSTEM; ENGINE; EQUIPMENT:ELECTRICAL. This Preliminary Information communication provides information to the technician with the steps to diagnose and repair vehicles with a Malfunction Indicator Lamp on. Technician may find a Diagnostic Trouble Code P0335 and or P0336 stored in the Power inverter module. Technician will need to inspect G113 if the ground eyelet is not tight replacing the bolt with a shorter bolt. If either of the Diagnostic Trouble Codes P0335 or P0336 are stored in both the Engine Control Module and the Power inverter module or the codes are current, please follow published Service Information diagnostics. If the vehicle is a model year 2014, update the Power Inverter Module with the latest software in TIS2Web.
PIP4859C2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING; ELECTRICAL SYSTEM:12V/24V/48V BATTERY. This Preliminary Information communication provides information to the technician on the steps to vacuum fill to ensure the cooling system is properly filled. Technician will need to use special tool GE-47716 Vac-N-Fill Coolant Refill Tool. Technician will also perform Hybrid/EV Battery Pack Coolant Pump Bleed Procedure in the GDS2 tool. After performing the GDS2 coolant bleed procedure drive vehicle for approximately 5 miles in a slalom type of situation to purge any remaining air from battery pack cooling plates.
PIP5000B2017-08-15. Service bulletin. ENGINE; ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician about vehicles that have a check engine light on. Technician will find Diagnostic Trouble Codes P0700 set in the Engine Control Module and P0797 set in the Transmission Control Module. Technician should use published Service Information diagnostics for the Diagnostic Trouble Codes.
PIP4910C2017-08-15. Service bulletin. ELECTRICAL SYSTEM:12V/24V/48V BATTERY; ENGINE AND ENGINE COOLING. This Preliminary Information communication provides information to the technician about servicing any of the cooling systems on the these vehicles, which includes the High Voltage Battery Assembly, pumps, reservoirs, hoses, air separators, radiators, PIM, engine or heater system it is important to use the proper coolant and water mixture. The Power Electronics / Charging and Battery Cooling systems require a 50/50 mix of GM DEX-COOL® and de-ionized water.
PIP51632017-08-15. Service bulletin. ENGINE AND ENGINE COOLING. This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
PIC59432017-08-15. Service bulletin. ENGINE AND ENGINE COOLING; ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician about vehicles that have no heat in EV electric mode Technician will find a Diagnostic Trouble Code B101D in the Coolant Heater Control Module. Technician will need to check the coolant heater control module for proper operation. If the Diagnostic Trouble Code B101D is set replace the Coolant Heater Control Module.
PIP52262017-08-15. Service bulletin. ENGINE AND ENGINE COOLING. This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Only replace the roller rocker that is missing needle bearings. Be sure to clean the oil drains to retrieve the needle bearings. Each roller rocker has 66 bearings.
PIP52222017-08-15. Service bulletin. ELECTRICAL SYSTEM; ENGINE; ELECTRICAL SYSTEM:12V/24V/48V BATTERY. This Preliminary Information communication provides information to the technician about the difficulty in detecting internal combustion engine misfires with a fully charged high voltage battery. Technician should ensure that the high voltage battery charge indicator is showing at least 2 bars below fully charged whenever performing strategy based diagnostics related to misfire.
PIP5163A2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING. This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
PIP4843D2017-08-15. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; ELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING. This Preliminary Information communication advises the technician that the Drive Motor Generator Control Module part number 24266807 is being placed on restriction through the General Motors Technical Assistance Center. Dealer will need to contact General Motors Technical Assistance Center for further assistance.
PIP52022017-08-15. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); ENGINE AND ENGINE COOLING. This Preliminary Information communication provides information to the technician the steps to diagnose and repair vehicles that have Check Engine Light illuminated with an "Engine Unavailable" and "Reduced Propulsion" messages on the Driver Information Center. Technician may find Diagnostic Trouble Codes a P0AB9 and P0AC4. Technician should not clear any Diagnostic Trouble Codes and ensure Global Diagnostic System 2 is up to date. Technician will need to use Global Diagnostic System 2 and check all modules for Diagnostic Trouble Codes. Now use Global Diagnostic System 2 to create freeze frame data from Hybrid Powertrain Control Module and the Engine Control Module and save a report. Technician will need to verify that the vehicle had not been run very low or out of fuel. Also verify the customer did not press the Power Button causing the vehicle to turn off while driving. Verify that the Internal Combustion Engine runs properly and no other engine related or communication related Diagnostic Trouble Codes are present. Technician should inquire if the remote star was used on the last two drive cycles before the Diagnostic Trouble Code set. Technician should update the Engine Control Module if so. Technician should inspect the ground locations G106 (engine block) and G113 (drive unit case) have been cleaned and are secure making sure the ground eyelets do not spin. Technician should also check for past service history for prior mechanical engine or wiring harness repairs. Inspect the cam timing connector and repair any damage.
PIP4670D2017-08-15. Service bulletin. ELECTRICAL SYSTEM; ENGINE. This Preliminary Information communication provides information to the technician about a no start or another concern after swapping an Engine Control Module or other modules from one vehicle to another. The Global Architecture electrical system associated with these vehicles does not allow controller swaps between vehicles.
PIP5008A2017-08-15. Service bulletin. ELECTRICAL SYSTEM; ENGINE. This Preliminary Information communication provides information to the technician about vehicles that have a Check Engine Malfunction Indicator Lamp on and possibly an Engine Unavailable message on the Driver Information Center. Technician may find Diagnostic Trouble Code?s P0AB9 in set in the Hybrid Powertrain Control Module and P0AC4 set in the Engine Control Module. Technician should not clear any Diagnostic Trouble Codes. Technician will need to verify that the vehicle has not been run very low or out of fuel, customer did not key off while driving, and the engine runs properly and no other engine related or communication related Diagnostic Trouble Codes are present. Technician will need to check for clean and tight ground location G106 and G113.
10-00-89-005F2017-07-18. Service bulletin. EQUIPMENT; ENGINE. This informational bulletin provides warranty policy information on revised wiring repair labor operations and required additional information.
16-NA-2222017-05-25. Service bulletin. ENGINE. THIS INFORMATIONAL BULLETIN PROVIDES THE TECHNICIAN WITH WHAT MAY HAPPEN TO AN ENGINE DUE TO LACK OF MAINTENANCE.
PIP5282A2017-05-18. Service bulletin. ENGINE. THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ABOUT THE CALCULATION AND OPERATION OF THE ENGINE OIL LIFE MONITOR. THE MONITOR CALCULATES THE PERCENT OF OIL LIFE REMAINING, BASED ON 3 PATHWAYS. THE FIRST PATHWAY FOR OIL LIFE CALCULATION IS ENGINE REVOLUTIONS. THE SECOND PATHWAY FOR OIL LIFE CALCULATION IS THE MILEAGE FORM THE LAST REST FOR ALL GENERAL MOTORS POWERTRAINS EXCEPT THE VOLT. THE THIRD PATHWAY FOR OIL LIFE CALCULATION IS THE AMOUNT OF TIME THE OIL IS IN THE ENGINE. THE VOLT USES A 2 YEAR TIMER INSTEAD OF 1 YEAR. IT ALSO USES THE ENGINE REVOLUTION COUNTER. IT DOES NOT USE THE MILEAGE PATHWAY TO COUNT DOWN.
PIP5029G2017-05-16. Service bulletin. ENGINE. THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT HAVE A MALFUNCTION INDICATOR LAMP ON OR ENGINE MISFIRE, ROUGH IDLE, EXTENDED CRANK, OR CRANK NO START IN SOME CASES. TECHNICIAN WILL NEED TO PERFORM PUBLISHED SERVICE INFORMATION DIAGNOSTICS. IF TECHNICIAN FINDS CARBON, AN UPPER ENGINE AND VALVE CLEANING SHOULD BE PERFORMED.
PIP4859D2017-03-15. Service bulletin. ENGINE AND ENGINE COOLING:COOLING SYSTEM. THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ON THE STEPS TO VACUUM FILL TO ENSURE THE COOLING SYSTEM IS PROPERLY FILLED. TECHNICIAN WILL NEED TO USE SPECIAL TOOL GE-47716 VAC-N-FILL COOLANT REFILL TOOL. TECHNICIAN WILL ALSO PERFORM HYBRID/EV BATTERY PACK COOLANT PUMP BLEED PROCEDURE IN THE GDS2 TOOL. AFTER PERFORMING THE GDS2 COOLANT BLEED PROCEDURE DRIVE VEHICLE FOR APPROXIMATELY 5 MILES IN A SLALOM TYPE OF SITUATION TO PURGE ANY REMAINING AIR FROM BATTERY PACK COOLING PLATES.
PI1237B2017-03-10. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM; EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL; EQUIPMENT. THIIS INFORMATION BULLETIN PROVIDES INFORMATION ON HOW THE EXHAUST AND INTAKE CAMSHAFT POSITION EXCITER WHEEL MUST BE INSTALLED PROPERLY TO PREVENT A CUSTOMER CONCERN ON AN INTERMITTENT CRANK/NO START.
PIP5189B2016-11-01. Service bulletin. ELECTRICAL SYSTEM; ENGINE. THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR THE CONCERN OF BLACK SMOKE WHEN STARTING THE VEHICLE AFTER SITTING.
PIP4786C2016-10-20. Service bulletin. ENGINE AND ENGINE COOLING. THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT MAY HAVE LOW OIL PRESSURE MESSAGE. TECHNICIAN MAY ALSO FIND A DIAGNOSTIC TROUBLE CODE P0521 IN THE ENGINE CONTROL MODULE. TECHNICIAN SHOULD FOLLOW ALL PUBLISHED SERVICE INFORMATION DIAGNOSIS. WHEN USING A SCAN TOOL IF THE OIL PRESSURE IS LOW BUT THE OIL PRESSURE AT THE OIL FILTER HOUSING IS CORRECT, TECHNICIAN SHOULD INSPECT THE VALVE LIFTER OIL FILTER FOR DEBRIS/SLUDGE THAT COULD BE RESTRICTING OIL FLOW TO THE OIL PRESSURE SENSOR. TECHNICIAN SHOULD REMOVE THE VALVE LIFTER OIL FILTER AND CLEAN IT. IF THE VALVE LIFTER OIL FILTER CANNOT BE CLEANED REPLACE IT.
PI1394A2016-10-19. Service bulletin. ENGINE. THIS INFORMATIONAL BULLETIN PROVIDES ADDITIONAL INFORMATION ON HOW TO INSTALL PISTONS AND SUGGEST WHAT TOOLS TO USE.
030604017I2016-10-18. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:DIESEL. THIS INFORMATIONAL BULLETIN EXPLAINS THE USE OF DIESEL FUEL ADDITIVES IN AN ENGINE, ARE NOT REQUIRED UNLESS THE CUSTOMER DESIRES ADDITIVES TO PREVENT FUEL CONCERNS DEPENDING ON FUEL OR TEMPERATURE RELATED CONDITIONS.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.