Service bulletins for the 2011 Chevrolet Volt
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
1715 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
By topic
| PIP5008A | 2017-08-15. Service bulletin. ELECTRICAL SYSTEM; ENGINE. This Preliminary Information communication provides information to the technician about vehicles that have a Check Engine Malfunction Indicator Lamp on and possibly an Engine Unavailable message on the Driver Information Center. Technician may find Diagnostic Trouble Code?s P0AB9 in set in the Hybrid Powertrain Control Module and P0AC4 set in the Engine Control Module. Technician should not clear any Diagnostic Trouble Codes. Technician will need to verify that the vehicle has not been run very low or out of fuel, customer did not key off while driving, and the engine runs properly and no other engine related or communication related Diagnostic Trouble Codes are present. Technician will need to check for clean and tight ground location G106 and G113. |
|---|---|
| PIC5491E | 2017-08-15. Service bulletin. ELECTRICAL SYSTEM; ELECTRICAL SYSTEM:SOFTWARE. This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. After the vehicle has powered down, remove power to the OnStar module for five minutes. After the power has been removed for five minutes, if the OnStar system is working release the vehicle. If the OnStar system is still inoperative continue with published Service Information diagnostics. Technician may need to contact General Motors Technical Assistance Center depending on the STID, Station ID, or OnStar Customer Identifier. |
| PIC3011H | 2017-08-15. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. This Preliminary Information communication provides information to the technician about vehicles that have the OnStar system does not respond properly to some numbers and/or voice commands. Dealer should direct the customer to review the operational characteristics in the OnStar Users Guide. |
| PIP5184 | 2017-08-15. Service bulletin. ELECTRICAL SYSTEM; ELECTRICAL SYSTEM:SOFTWARE. This Preliminary Information communication advises the technician that when replacing the camshaft part number 12626660. Technician will need to ensure that the date code and the finish of the camshaft. If the cam is discolored or has chatter marks, have parts department send the cam back as (MR code7) new defective. |
| PIC5523C | 2017-08-15. Service bulletin. ELECTRICAL SYSTEM; ELECTRICAL SYSTEM:12V/24V/48V BATTERY. This Preliminary Information communication provides information to the technician about vehicles that may have a no crank with a "Waiting to Initialize" message displayed on the Driver Information Center. Technician may also find a Diagnostic Trouble Code P0AFA in the Hybrid Powertrain Control Module 2. Technician will need to insure that the 12 volt battery is fully charged. Then install the Multiple Diagnostic Interface and open Global Diagnostic System 2 open the Hybrid Powertrain Control Module then use the Control Function feature to select ?Check High Voltage System related Diagnostic Trouble Code?s?. Then click on ?Reset? to clear the Diagnostic Trouble Codes. Wait 45 seconds then exit the screen. Next select Check Secured High Voltage DTCs? select the ?Clear DTCs? then click on ?Reset? to clear the Diagnostic Trouble Codes. Now remove the Multiple Diagnostic Interface from the vehicle then shut the vehicle down and let it sleep for three minutes. At this time disconnect the 12 volt battery and touch the battery cables together and then re-install after 15 seconds. Start the vehicle after a 3 minute waiting period. If the vehicle still has a no crank concern follow published Service Information diagnosis. |
| PIP4871C | 2017-08-15. Service bulletin. ENGINE. This Preliminary Information communication provides information to the technician about vehicles that may have Malfunction Indicator Lamp on. Technician my find Diagnostic Trouble Code P1B0F and or Diagnostic Trouble Code P1B10 set in the Hybrid Powertrain Control Module. Dealer should explain to the customer that inadvertently shutting the vehicle off while in motion (out of park) may cause this Malfunction Indicator Lamp to illuminate, and this is design intent. |
| PIT4943C | 2017-08-15. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL; FUEL SYSTEM, GASOLINE; SERVICE BRAKES, HYDRAULIC. This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0442. Technician will need to review Techlink article from May 2013 titled "Using the Evaporative Emissions System Tester" Technician will need to follow these steps to help diagnose the issue. First after the P0442 has been verified do not disturb any of the fuel system components. The technician now can use the scan tool to close the Evaporative Emissions System. If possible change the tank pressure sensor units from inch_H2O to milimeter_Hg for better resolution. Now the vehicle can be stared to monitor the tank pressure sensor output value for approximately two minutes. If the tank pressure sensor value does change, pressurize the fuel tank side of the purge solenoid with the GE 41413-A / J 41413-A and the necessary adaptors. Now add smoke and allow pressure to stabilize for 2 minutes. If smoke is allowed to pass through the purge solenoid, replace the purge solenoid. If the tank pressure sensor value does not change, then install CH-48096 adaptor between the purge line from the canister and the purge solenoid. With the Evaporative Emissions System closed, pressurize the system through the CH-48096 adaptor and allow the system to completely stabilize, by observing the Press / Vac Gauge for a minimum of 5 minutes. Now add smoke to the system with GE 41413-A / J 41413-A after system stabilization. Now inspect the purge solenoid, engine side, fuel cap, canister vent solenoid filter and any line quick connects. When the leak is unable to be located, test under a vacuum condition. his type of leak may be detected by using the scan tool Purge/Seal function to create a vacuum in the Evaporative Emissions System and then observe the FTP sensor parameter for vacuum decay. |
| PIT4945F | 2017-08-15. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. This Preliminary Information communication provides information to the technician being unable to program fobs to the vehicle. Technician will need to ensure the key FOB is a new unit and has not been programmed to another vehicle previously. |
| PIT5076D | 2017-08-15. Service bulletin. ELECTRICAL SYSTEM; STEERING; SERVICE BRAKES. This Preliminary Information communication advises the technician to insure that global diagnostic service 2 diagnostic packages are up to date prior to learning the steering angle sensor for a diagnostic trouble code C710 symptom code 71 set in the electronic brake control module or the power steering control module. When rechecking for diagnostic trouble codes a U0074 U0077, U0180D, U01293, U0126, U0125, C0186, C0196, or C0287 are set and will not clear diagnose the Chassis bus. If no fault is found in the chassis bus check for an multiple diagnostic interface to data link connector issue. Technician is to try a different multiple diagnostic interface cable and attempt the steering angle sensor learn again following service information instruction then try to clear the codes again. |
| PIP4905C | 2017-08-15. Service bulletin. ELECTRICAL SYSTEM:WIRING; ELECTRICAL SYSTEM:12V/24V/48V BATTERY; ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician about vehicles that have a no charge condition when using either the stationary 240V or the 120V charger. Technician may find Diagnostic Trouble Code P0D26 set in the Hybrid Powertrain Control Module 2. Technician will need to check the last 8 digits of the (VIN) Vehicle Identification Number. If the Vehicle Identification Number number is less than Vehicle Identification Number BU100954, perform the latest version of PIP4875 to program the Hybrid Powertrain Control Module 2. If the vehicle is a return or built after Vehicle Identification Number BU100954 Plug in the 120V charger and note the behavior of the charge indicator light on the Instrument Panel and the lights on the charge cord set Electric Vehicle Supply Equipment. If the light on the Instrument Panel is not steady green during a charging event, and the two upper charge cord set lights are steady green, record a GDS 2 snapshot from the Battery Charger Control Module Data. While monitoring the data in Global Diagnostic System 2, manipulate the charge cord coupler for proximity voltage changes. If the data has an erratic signal inspect the charge port receptacle connector for signs of water intrusion or corrosion in both the vehicle harness side and charge port side. |
| PIP4890A | 2017-08-15. Service bulletin. ELECTRICAL SYSTEM:12V/24V/48V BATTERY; ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician about vehicles that will not start and a message on the Drivers Information Center (DIC) displays: "Battery Too Cold, Plug In To Warm" message. Dealer should communicate to the customer to plug the vehicle in to allow the charging system to warm the high voltage battery, and then the vehicle can be started. |
| PIT4610D | 2017-08-15. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. This Preliminary Information communication provides information to the technician that First Responder Guides for General Motors vehicles can be accessed via the web at http://www.gmstc.com. |
| PIC5423B | 2017-08-15. Service bulletin. ELECTRICAL SYSTEM: INTEGRATED TRAILER BRAKE CONTROL. This Preliminary Information communication provides information to the technician with some additional steps that are needed to help perform a successful brake bleed on the Chevy Volt or the Cadillac ELR. Technician will need to use the tool J-29532-B to maintain 30 pounds per square Inch during the brake bleeding process. |
| PIC5383C | 2017-08-15. Service bulletin. ELECTRICAL SYSTEM; SERVICE BRAKES. This Preliminary Information communication advises the technician that the Electronic Brake Control Module and Brake Pressure Modulator Valve for the Chevrolet Volt are being placed on restriction through the General Motors Technical Assistance Center. Dealer will need to contact General Motors Technical Assistance Center for further assistance. |
| PIC5954 | 2017-08-15. Service bulletin. EQUIPMENT:APPLIANCE:AIR CONDITIONER; SEATS. This Preliminary Information communication provides information to the technician about vehicles that have heated seats inoperative. Technician may find Diagnostic Trouble Code U0209 in the Heater-Vent-Air Conditioning. Dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern. |
| PIC5436B | 2017-08-15. Service bulletin. ELECTRICAL SYSTEM:IGNITION; ELECTRICAL SYSTEM; SERVICE BRAKES. This Preliminary Information communication provides information to the technician some vehicles may have a Service Stabilitrak message and a red brake lamp illuminated on the Instrument Panel Cluster. Technician may find a Diagnostic Trouble Code C0196 in the Electronic Brake Control Module. This concern may be preset after the vehicle was flat towed or just came off a car carrier. Technician will need to perform a Multi Axis sensor learn and a Diagnostic Trouble Code clear in the Electronic Brake Control Module. Then shut ignition off, open and close driver door and let vehicle sit for 3 minutes. After the vehicle has slept for 3 minutes start the vehicle and let it run in park for 10 seconds. Now the vehicle will need to be driven for 30 seconds over 20 miles per hour. If code is cleared and doesn't reset, release the vehicle to the customer. If code resets follow normal diagnosis in Service Information. |
| PIC5381B | 2017-08-15. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT:APPLIANCE:AIR CONDITIONER. This Preliminary Information communication advises the technician that the AC Compressor and Integrated Control Module are being placed on restriction through the General Motors Technical Assistance Center. Dealer will need to contact General Motors Technical Assistance Center for further assistance. |
| PIC5383B | 2017-08-15. Service bulletin. ELECTRICAL SYSTEM; SERVICE BRAKES. This Preliminary Information communication advises the technician that the Electronic Brake Control Module and Brake Pressure Modulator Valve for the Chevrolet Volt are being placed on restriction through the General Motors Technical Assistance Center. Dealer will need to contact General Motors Technical Assistance Center for further assistance. |
| PIC5380F | 2017-08-15. Service bulletin. POWER TRAIN; ELECTRICAL SYSTEM. This Preliminary Information communication advises the technician that the K114B Hybrid Powertrain Control Module 2, also known as the Hybrid Powertrain Control Module 2 part numbers 22994053 and 22985723 are being placed on restriction through General Motors Technical Assistance Center. Dealer will need to contact General Motors Technical Assistance Center for further assistance. |
| PIP4840K | 2017-08-15. Service bulletin. POWER TRAIN. This Preliminary Information communication advises the technician that the 4ET50 transmission assembly and component restriction will be administered by the General Motors Technical Assistance Center. Dealer will need to contact General Motors Technical Assistance Center for further assistance. |
| PIC5453A | 2017-08-15. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. This Preliminary Information communication provides information to the technician that General Motors and General Motors of Canada Company do not support cross border sales. The General Motors of Canada Customer Care Centre is the sole authorized provider of a certification confirmation letter which helps our customers identify if their vehicles meets the required USA regulatory standards necessary for importation into the USA. |
| PIC5978 | 2017-08-15. Service bulletin. ELECTRICAL SYSTEM:PROPULSION SYSTEM:TRACTION BATTERY; STRUCTURE:BODY:HATCHBACK/LIFTGATE. This Preliminary Information communication provides information to the technician about vehicles that have Diagnostic Trouble Code P0606 during normal vehicle servicing procedures such as clearing codes or connecting the 12 volt battery. To clear the Diagnostic Trouble Code technician will need to close all doors and rear hatch, press and hold the power button to put the vehicle into service mode, clear the Diagnostic Trouble Code using Global Diagnostic System 2, Power off the vehicle, open and close the driver?s door, wait one minute, and start vehicle and ensure Malfunction Indicator Lamp is not illuminated. |
| PIT5264 | 2017-08-15. Service bulletin. EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.. This Preliminary Information communication provides information to the technician about vehicles that when a Canadian customer may comment that when they travel to the United States, they are unable to connect to OnStar or use hands free calling. Dealer can advise the customer that the existing cell phone provider not having roaming agreements in areas outside of Canada. At this time, a customer has the option of contacting OnStar to have a 500 number loaded for OnStar operation while in the United States. |
| PIC5374C | 2017-08-15. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM). This Preliminary Information communication provides information to the technician about vehicles that have a frequent "off route" messages while following Turn by Turn route. Technicians will need to remove power from the Vehicle Communication Interface Module for one hour and retest for the concern. |
| PIC5959A | 2017-08-15. Service bulletin. EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.. This Preliminary Information communication provides information to the technician about vehicles that has no XM audio on certain channels but XM channel info is displayed. Technician will need to contact XM and deactivate and activate the module. |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.