WenmarOpen by Wenmar Pro

Service bulletins for the 2015 Chevrolet Tahoe

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

2584 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Only bulletins with component: Engine are shown. Show all

Bulletins, newest first
PIP54422017-08-15. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM. This Preliminary Information communication provides information to the technician about vehicles that have an exhaust leak, noisy exhaust, or noise mid-vehicle. Technician will need to check for an unseated pipe to pipe mid-joint connection. Technician will need to install new exhaust band.
PIP5382F2017-08-15. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL; ENGINE. This Preliminary Information communication advises the technician that generation 5 engines with Regular Production Option Code L83, L86, or LV3 may have an oil consumption concern were one quart in 2000 miles is being used. Dealer will confirm oil level was properly checked per Owner?s Manual, and check the bolt torque on the Valve Lifter Oil Manifold Assembly, before you contacting General Motors Product Quality Center.
PIP52522017-08-15. Service bulletin. ENGINE. This Preliminary Information communication provides information to the technician about vehicles that the engine may run hot with the snow plow installed. Do not exceed 64?kilometers per hour / 40?miles per hour with a snow plow mounted to the vehicle even if equipped with VYU. The vehicle could overheat and be damaged.
PIP5211B2017-08-15. Service bulletin. ELECTRICAL SYSTEM; POWER TRAIN; EQUIPMENT ADAPTIVE/MOBILITY; ENGINE. This Preliminary Information communication provides information to the technician the steps needed to diagnose and repair vehicles with a rough idle and/or vibration at idle in Drive. This condition will not be present in Park, or Neutral. This concern may be caused by ground out within the one or both engine mounts. Technician will use CH-51450-A (Pico Oscilloscope) to measure the vibration disturbance. If the vibration concern is E1.5 in the horizontal / lateral direction with Pico sensor mounted in seat track as indicated ? continue with steps to reduce the amplitude of the vibration by adding spacers in key locations to reduce ground out within the engine mounts. The 6.2L engine has a characteristic E1 which can be felt, and may be described as a lopey idle. Do not confuse 6.2L E1 characteristic (not caused by mount ground-out), with E1.5 normal idle characteristics being transmitted into the truck via ground-out thru the engine mounts. If measuring high at the seat track 12 mg or greater; replacement of the engine mounts should help reduce the amplitude of the vibration. If the disturbance measures at the seat track as E 1.5 lateral in the range of approximately 2.5 - 8 mg using a tri-axis sensor. Then place tri-axis Pico sensor on the inboard seat track forward-most location to record measurement of the rough idle vibration concern. With the Heater-Vent-Air Conditioning on perform several short heavy launch events from stop to stop to bring the temperatures back up while attempting to re-create the rough idle vibration in Drive with Pico sensor placed on inboard seat track; while the vibration is active ? Record Pico reading. This method seems to provide better results than extended test drives. If the Pico reading for E1.5, with vibration active, at specified seat track location measures close to 2mg or less use Service Information to diagnose rough idle / vibration. If the Pico reading for E1.5, with vibration active, at the inboard forward seat track
PIP5029F2017-08-15. Service bulletin. ENGINE. This Preliminary Information communication provides information to the technician about vehicles that have a Malfunction Indicator Lamp on or engine misfire, rough idle, extended crank, or crank no start in some cases. Technician will need to perform published Service Information diagnostics. If technician finds carbon an upper engine and valve cleaning should be performed.
PIT53502017-08-15. Service bulletin. ENGINE; ELECTRICAL SYSTEM:SOFTWARE. This Preliminary Information communication advises the technician that there have been some reports that the current engine hours are not correct and display 0.0. Technician will need to program the Instrument Panel Cluster using Service Programming System.
PIT5448A2017-08-15. Service bulletin. ENGINE. This Preliminary Information communication advises the technician with a tip when the vehicle stops running after it has been idling for 2.5 hours. This is normal operation of the vehicle built with regular production code BTM.
PIP5230B2017-08-15. Service bulletin. ENGINE; EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. This Preliminary Information communication advises the technician before replacing the crankshaft to review the following. Dealer should complete the Service Information diagnostics and the Cost Comparison Worksheet for Assembly Repair vs. Replacement. Technician will use the latest version of 09-06-04-026G to verify the Engine Control Module calibration is not an aftermarket calibration. If the customer prefers to keep the original numbers matching engine please call General Motors Technical Assistance Center for repair direction.
PIP5179A2017-08-15. Service bulletin. FUEL SYSTEM, GASOLINE:FUEL INJECTION SYSTEM; ENGINE. This Preliminary Information communication provides information to the technician about vehicles that have extended or long crank time during cold ambient air temperatures. Direct Injection systems run at higher pressures, and the mechanical pump on the engine must build up the required pressure before the first injection event occurs. Direct Injection engines may have slightly longer cold crank times than that of port fuel engines.
PIP5272A2017-08-15. Service bulletin. ENGINE. This Preliminary Information communication provides information to the technician about vehicles that may have low oil pressure after an oil change. Technician will inspect the oil filter part number PF63E. Part number PF48 oil filter will fit but will cause a low oil pressure concern.
PIT54482017-08-15. Service bulletin. ENGINE. This Preliminary Information communication provides information to the technician about vehicles that stop running after it has been idling for 2.5 hours. This is normal operation of the vehicle built with regular production code BTM.
PIT54472017-08-15. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:MANIFOLD/HEADER/MUFFLER/TAIL PIPE. This Preliminary Information communication provides information to the technician on the steps needed to diagnose and repair vehicles that may have a rattle noise from the dash. Technician will need to inspect for the rear heater pipes contacting the passenger side exhaust manifold. If the rear heater pipe is found to be contacting the exhaust manifold, reposition the heater pipe so it no longer makes contact.
PIP5211C2017-08-15. Service bulletin. ENGINE; SUSPENSION. This Preliminary Information communication provides information to the technician the steps needed to diagnose and repair vehicles with a rough idle and/or vibration at idle in Drive. This condition will not be present in Park, or Neutral. This concern may be caused by ground out within the one or both engine mounts. Technician will use CH-51450-A (Pico Oscilloscope) to measure the vibration disturbance. If the vibration concern is E1.5 in the horizontal / lateral direction with Pico sensor mounted in seat track as indicated ? continue with steps to reduce the amplitude of the vibration by adding spacers in key locations to reduce ground out within the engine mounts. The 6.2L engine has a characteristic E1 which can be felt, and may be described as a lopey idle. Do not confuse 6.2L E1 characteristic (not caused by mount ground-out), with E1.5 normal idle characteristics being transmitted into the truck via ground-out thru the engine mounts. If measuring high at the seat track 12 mg or greater; replacement of the engine mounts should help reduce the amplitude of the vibration. If the disturbance measures at the seat track as E 1.5 lateral in the range of approximately 2.5 - 8 mg using a tri-axis sensor. Then place tri-axis Pico sensor on the inboard seat track forward-most location to record measurement of the rough idle vibration concern. With the Heater-Vent-Air Conditioning on perform several short heavy launch events from stop to stop to bring the temperatures back up while attempting to re-create the rough idle vibration in Drive with Pico sensor placed on inboard seat track; while the vibration is active ? Record Pico reading. This method seems to provide better results than extended test drives. If the Pico reading for E1.5, with vibration active, at specified seat track location measures close to 2mg or less use Service Information to diagnose rough idle / vibration. If the Pico reading for E1.5, with vibration active, at the inboard forward seat track
PIT5245B2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING. This Preliminary Information communication provides information to the technician about vehicles that the blower motor may be noisy or vibrate when running. This concern will only occur when the temperatures is below 32 degrees Fahrenheit and if the blower motor is removed while still cold, ice may be found on the blower motor cage. This concern could be caused by water leaking or snow ingestion into the Heater-Vent-Air Conditioning case. Technician is to perform normal water testing diagnostics while the Heater-Vent-Air Conditioning is running, looking for water leaking past the plenum cover. If water is leaking past the cover remove the cover and install a 12x12 snow resistant screen to the fresh air intake. Reseal and install the plenum cover cap using Kent air dry sealer or equivalent.
PIP52882017-08-15. Service bulletin. ENGINE. This Preliminary Information communication advises the technician to check for an engine build code of K and the dates between 15005 and 15117, the customer concern is an engine oil leak at the oil filter location of the oil pan. A loose oil filter adapter is found to be the cause of the concern, tighten it to 55 newton meters or 40 foot pounds. It is also advised to clean any residual oil from the oil pan area.
PIP52822017-08-15. Service bulletin. ENGINE AND ENGINE COOLING. This Preliminary Information communication advises the technician about the calculation and operation of the engine oil life monitor. The monitor calculates the percent of oil life remaining, based on 3 pathways. The first pathway for oil life calculation is engine revolutions. The second pathway for oil life calculation is the mileage form the last rest for all General Motors powertrains except the Volt. The third pathway for oil life calculation is the amount of time the oil is in the engine. The Volt uses a 2 year timer instead of 1 year. It also uses the engine revolution counter. It does not use the mileage pathway to count down.
09-06-04-026M2017-08-15. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; ENGINE. This informational bulletin provides information on identifying non-GM (aftermarket) engine calibrations for gasoline engines using Tech 2 or GDS 2.
PIP5248C2017-08-15. Service bulletin. SUSPENSION:FRONT:WHEEL BEARING; ENGINE. This Preliminary Information communication provides information to the technician on the steps need to diagnose and repair vehicles that may have stalling shudder and/or hard shifting into 1st gear or reverse vibration on launch (with excessive crankshaft end play). Technician will test to determine if the crank shaft end play is within specification 0.0015–0.0086 inch. If end play is found to be out of specification, remove engine and inspect for possible crankshaft thrust bearing and/or crankshaft for wear. Inspect thrust bearing for wear on one side and crankshaft on that “mating” surface. If the thrust bearing has three vertical channels worn off replace connecting rod bearings, main bearings, thrust bearing and crankshaft. If working on a Corvette the oil tank with lines and oil cooler are both required to be replaced if equipped.
PIT5308B2017-08-15. Service bulletin. STRUCTURE:BODY:HATCHBACK/LIFTGATE; ELECTRICAL SYSTEM; ENGINE. This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that have remote start is inoperative, power lift gate Regular Production Option Code (TB5) is inoperative with the ignition off, Crank no start, Start and Stall, and vehicles equipped with the diesel engine, the blower motor may stay on after the engine is turned off. Technician may find Diagnostic Trouble Code P2537 and/or P129Dset. Technician will need to Use a voltmeter and check circuit 5985 at the Engine Control Module and Transmission Control Module. If no or low voltage is found, use the wiring diagram in Service Information and perform normal circuit diagnosis.
PI1513D2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING:COOLING SYSTEM:RADIATOR ASSEMBLY; ENGINE AND ENGINE COOLING. This preliminary information bulletin provides a procedure for radiator and engine coolant thermostat replacement to eliminate coolant smell and/or a slight leak at the radiator.
PI1513C2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING:COOLING SYSTEM:RADIATOR ASSEMBLY. This preliminary information bulletin provides a procedure for radiator and engine coolant thermostat replacement to eliminate coolant smell and/or a slight leak at the radiator.
PIT5206D2017-08-15. Service bulletin. ELECTRICAL SYSTEM; ENGINE; SERVICE BRAKES, HYDRAULIC:PEDALS AND LINKAGES. This Preliminary Information communication provides information to the technician with the steps on diagnosing and repairing vehicles that may have unwanted grade braking, reduced engine power with no Driver Information Center messages ? Brake Pedal Override Feature ?, transmission busy or frequent shifting up or down, and Diagnostic Trouble Codes P057B, P057C, and/or P057D may or may not be set. Technician will use this preliminary information to find the brake pedal position data parameters in the scan tool, and also to provide some additional diagnostic help. These issues may be caused by an incorrect brake pedal position sensor input to the engine control module. Technician will verify with the scan tool if the engine control module has the correct parameters for the brake pedal position sensor. If an engine control module brake pedal position sensor relearn is performed, the truck may be temporarily repaired until the intermittent wiring issue between the engine control module and brake pedal position sensor occurs again. On 2014 and newer trucks inspect and repair any damage to X115 and X119. On the 2014 and previous trucks inspect and repair any damage to X205.
PIP5382A2017-08-15. Service bulletin. ENGINE; EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. This Preliminary Information communication advises the technician that generation 5 engines with Regular Production Option Code L83, L86, or LV3 may have an oil consumption concern were one quart in 2000 miles is being used. Dealer will confirm oil level was properly checked per Owner?s Manual, and check the bolt torque on the Valve Lifter Oil Manifold Assembly, before you contacting General Motors Product Quality Center.
PIT5232B2017-08-15. Service bulletin. ENGINE; ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician the steps to diagnose and repair the concern of the display is showing 32° F (0° C) after a battery or reprogramming a module. The outside temperature will begin to update if driven above 20 mph for at least 5 minutes. If the vehicle speed drops below 20 mph, the timer will reset and the display will stop updating. Once the display starts to update it may take several more minutes of driving above 20 mph for the display to fully update. Also if the vehicle is shut off for more than 8 hours the display will update when the ignition is turned on.
PIP5232C2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR. This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. It is recommended to inspect for a poor crimp on the coil grounds ring terminal at the engine block for the bank with the concern and repair the wire.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.