WenmarOpen by Wenmar Pro

Service bulletins for the 2015 Chevrolet Spark

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

1402 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Only bulletins with component: Software are shown. Show all

Bulletins, newest first
03-08-46-004S2017-08-31. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. This informational bulletin provides information on OnStar® VCIM is currently restricted parts. By working closely with our dealers and technicians, through the part restriction process, the General Motors team will gain a better understanding of any field concerns that may develop.
PIC6090A2017-08-15. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. This Preliminary Information communication provides information to the technician for the radio locking up usually after an OnStar turn by turn route. Engineering is aware of the concern and is working to release software to correct the concern. If the concern happens it is normally corrected by turning the ignition off opening the door to cancel retained accessory power and then restarting the vehicle. If the concern is still present after the ignition cycle it may be necessary to remove the radio?s fuse for 2 minutes and reinstall. Communicate to the customer that General Motors is working on a solution for this concern.
PIP5155A2017-08-15. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL; ELECTRICAL SYSTEM:SOFTWARE. This Preliminary Information communication provides information to the technician about vehicles that may have Service Vehicle Soon Lamp (SVS) or Check Engine Lamp (CEL) is on after charging using a 240V charging station. Technician may find a Diagnostic Trouble Code P1EE6 stored current or history. When published Service Information diagnostics do not lead to repair the Hybrid Powertrain Control Module 2 will need to be reprogrammed using Service Programming System.
PIC5436C2017-08-15. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. This Preliminary Information communication provides information to the technician some vehicles may have a Service Stabilitrak message and a red brake lamp illuminated on the Instrument Panel Cluster. Technician may find a Diagnostic Trouble Code C0196 in the Electronic Brake Control Module. This concern may be preset after the vehicle was flat towed or just came off a car carrier. Technician will need to perform a Multi Axis sensor learn and a Diagnostic Trouble Code clear in the Electronic Brake Control Module. Then shut ignition off, open and close driver door and let vehicle sit for 3 minutes. After the vehicle has slept for 3 minutes start the vehicle and let it run in park for 10 seconds. Now the vehicle will need to be driven for 30 seconds over 20 miles per hour. If code is cleared and doesn't reset, release the vehicle to the customer. If code resets follow normal diagnosis in Service Information.
PIP52712017-08-15. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. This Preliminary Information communication provides information to the technician about vehicles that may have inaccurate charge completion time displayed or delayed charging concerns. Technician will insure the time and date is current on the radio. Also update the Hybrid Powertrain Control Module 2 using Service Programming System. If the concern is still present General Motors Technical Assistance Center for further assistance.
PIP52672017-08-15. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. This Preliminary Information communication provides information to the technician about vehicles that may have a Check Engine Lamp or Service Vehicle Soon lamp on after charging. If the technician finds Diagnostic Trouble Codes P16C4 or P16C5 set in history, the Hybrid Powertrain Control Module will need to be reprogrammed. If the Diagnostic Trouble Codes are current or return and the Hybrid Powertrain Control Module and the Battery Charger Control Module have the current calibrations then processed to follow published Service Information diagnostics. This may lead to Battery Charger Control Module replacement.
PIP52652017-08-15. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. This Preliminary Information communication provides information to the technician about vehicles that may have a Service Vehicle Soon on, a Reduced Power Mode Message, or the vehicle will not start. Technician may find Diagnostic Trouble Code P1EAB stored. Technician should not clear the Diagnostic Trouble Code. Technician will need to use Global Diagnostic System 2 to review Hybrid Powertrain Control Module 2 Freeze Frame / Failure Records for DTC P1EAB. If the maximum cell voltage is not greater than 4.58?V, check to see if the Battery Engine control Module has the latest Service Programming System calibration. If there is a new calibration available for the battery engine control module then the module should be updated. If the battery engine control module cell voltage displayed in the Freeze Frame / Failure Records or the live cell voltage is over 4.58V, then follow currently published in Service Information. If the latest calibration is already installed or the battery engine control module has been reprogrammed previously and the concern is intermittent, contact General Motors Technical Assistance Center for further assistance.
PIC5880E2017-08-15. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. This Preliminary Information communication advises the technician that the Onboard Charge Module, Hybrid Powertrain Control Module 2, Air Compressor Control Module, Accessory Power Module, Hybrid Powertrain Control Module, Drive Motor Generator Power Inverter Module, AC Charger - Low Content High Voltage Battery Disconnect Control Module, and the DC Fast Charger - High Content High Voltage Battery Disconnect Control Module parts have been placed on part restriction thought General Motors Technical Assistance Center. Dealer will need to contact General Motors Technical Assistance Center for further assistance.
PIP5251A2017-08-15. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. This Preliminary Information communication provides information to the technician about vehicles that may have a Malfunction Indicator Lamp on. Technician may find a diagnostic trouble code P0324 set as a current or history. Also a rattle or spark knock type noise may also be heard while driving. Technician will need to let the vehicle cold soak overnight. Then clear the diagnostic trouble code in the Engine Control Module. Then use Global Diagnostic System 2 to monitor the Total Knock Retard Parameter. Let the vehicle run at idle for ten seconds with the park brake turned on. Hold the brake down and place the vehicle in ?Drive? for automatic transmission or drive gear for manual gear box then bring the engine between 1800 and 2000 RPM for 10 seconds then return to idle for 5 second. Repeat this cycle 7 times. If the readings during the raised RPM testing were NOT continuously above 6.0 degrees for more than 5 seconds, no further action is required within the scope of this bulletin. If the readings during the raised RPM testing were continuously above 6.0 degrees for more than 5 seconds, the vehicle requires repair. Technician will need to verify the engine oil level is correct. After insuring the engine oil level is correct allow the engine to idle for one hour. Every 15 minutes increase the engine rpms to 2000 and hold for 5 minutes. Or drive the vehicle for 25 to 30 miles. Allow the engine to cold soak overnight and then repeat the inspection procedure. Then review the Global Diagnostic System 2 session log Total Knock Retard Parameter. Technician will need to General Motors Technical Assistance Center for further assistance.
PI0592D2017-08-15. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. This informational bulletin provides information on service programming system (SPS) errors.
09-06-04-026M2017-08-15. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; ENGINE. This informational bulletin provides information on identifying non-GM (aftermarket) engine calibrations for gasoline engines using Tech 2 or GDS 2.
PIT5236G2017-08-15. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Technician will check Global Warranty Management system for customer satisfaction program 15086 status. If the status of the customer satisfaction program 15086 was not completed follow the steps to get the Telematics Communication Interface Control Module replaced. If the status of customer satisfaction program 15086 is found completed contact General Motors Technical Assistance Center OnStar group for further assistance.
PIP54942017-08-15. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. This Preliminary Information communication provides information to the technician about the operation or performance of the CVT7 transmission. This information also provides diagnostic tips using GDS2 software for the CVT7 transmission.
03-08-46-004P2017-08-15. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. This informational bulletin communicates part restriction and ordering process information for OnStar®Vehicle Communication Interface Modules (VCIM) (GMNA Only).
05-06-04-060A2017-08-15. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. This informational bulletin communicates Information to technicians on control module Diagnostic Trouble Code(s) (DTC)(s) P0601, P0602, P0603, P0604, P0606, P062F, P06F3, P1621 which can be shared in multiple modules.
PIT5389C2017-08-15. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.
PIC4935F2017-08-15. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. This Preliminary Information communication provides information to help the dealership technicians perform a parasitic drain test for the OnStar module. When performing battery parasitic drain test, there may be some confusion as to what the normal power consumption reading should be from the OnStar system.
PIP4723B2017-08-15. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.
PIC4801H2017-08-15. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that may have an OnStar Turn-By-Turn Navigation the system that is inoperative. Technician verifies there are no Diagnostic Trouble Codes are present in the Antilock Braking System and Vehicle Communication Interface Module of the vehicle. If no Diagnostic Trouble Codes found call OnStar using the Blue button on the OnStar key pad and ask the advisor for a turn by turn route. Also make a OnStar personal call and a call into the vehicle. If normal diagnostics do not lead to a resolution technician will need to call General Motors Technical Assistance Center for further assistance.
PIC3278G2017-08-15. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; STEERING. This Preliminary Information communication provides information to the technician the steps needed to diagnose and repair the vehicles that may have unwanted or phantom phone calls. Technician will need to determine what type of call the customer is having that is unwanted. The vehicle may receive an incoming call just like any other phone. Typically the customer will hear the phone ringing in the vehicle. This scenario also includes incoming Bluetooth calls. One type of unwanted call can be made if the key pad is faulty the OnStar system will try to make a blue button call for shorted voltage in the circuits. The OnStar module could have an internal fault and produce a ″Phone Unavailable″ audio message also it may have a Diagnostic Trouble Code U1500 or B1000. Refer to diagnostics for the Diagnostic Trouble Code making sure to follow any applicable Bulletins or Preliminary Information sheets. A “Ready” or “OnStar ready” audio message heard while driving. In some cases it has been found that the customer is inadvertently pressing the ″push to talk″ button on the steering wheel controls. On rare occasions, other issues in the steering column or Steering Wheel Control system may induce this concern.
PIC5880J2017-08-15. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. This Preliminary Information communication advises the technician that the Onboard Charge Module, Hybrid Powertrain Control Module 2, Air Compressor Control Module, Accessory Power Module, Hybrid Powertrain Control Module, Drive Motor Generator Power Inverter Module, AC Charger - Low Content High Voltage Battery Disconnect Control Module, and the DC Fast Charger - High Content High Voltage Battery Disconnect Control Module parts have been placed on part restriction thought General Motors Technical Assistance Center. Dealer will need to contact General Motors Technical Assistance Center for further assistance.
PIC5588C2017-08-15. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. This Preliminary Information communication provides information to the technician on the programming and activation of the OnStar system. For many 2008 and prior model year GM vehicles, the programming is performed using the Tech 2 and the activation is initiated by a Service Programming System. For the 2010 and UP model year vehicles, the OnStar set-up procedure and OnStar Activation request have been combined into a single programming event called OnStar Set-up and Activation in Service Programming System.
PIP4902J2017-08-15. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
PIT5236J2017-08-15. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM). This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Technician will need to ensure campaigns 14395 or 15086 are completed. Technician will need to use Global Diagnostic System 2 and gather information and contact General Motors Technical Assistance Center for further assistance.
16-NA-0112017-08-15. Service bulletin. EQUIPMENT:ELECTRICAL; ELECTRICAL SYSTEM:SOFTWARE. This technical bulletin provides a procedure to update your apple product to the latest software version to correct a condition of infotainment system will not return to media after bluetooth call ends

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.