WenmarOpen by Wenmar Pro

Service bulletins for the 2014 Chevrolet Silverado

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

3313 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Bulletins, newest first
PIC6075A2017-08-15. Service bulletin. EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM). This Preliminary Information communication provides information to the technician about vehicles that navigation system has inaccurate estimated time of arrival. This is a normal operating characteristic of the New Generation Infotainment system.
PIT54322017-08-15. Service bulletin. EQUIPMENT; SERVICE BRAKES, HYDRAULIC; ELECTRICAL SYSTEM: INTEGRATED TRAILER BRAKE CONTROL. This Preliminary Information communication provides information to the technician about vehicles that have a Shudder, bounce, bucking from the rear of the truck while braking when towing a gooseneck or fifth wheel trailer. Technician will need to measure the actual truck and trailer weights, with the trailer loaded to the point that exhibits the condition. If any weight parameter is exceeded such as the Front Gross Axle Weight Rating, Rear Gross Axle Weight Rating, Gross Vehicle Weight Rating, or Gross Combined Weight Rating the load must be reduced before investigating further. If evaluation of the trailer?s brakes indicates trailer brake capability is adequate, adjust brake controller per the Trailer Gain Adjustment Procedure described in the Driving and Operating section of the Owner?s Manual and evaluate truck and trailer combination for braking shudder.
PIT5344B2017-08-15. Service bulletin. EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.. This Preliminary Information communication provides information to the technician about vehicles with a CD player is inoperative. Technician should cycle power to the CD play and retest. If the CD player starts working advise the customer that we apologize for this inconvenience and that General Motors is working on a permanent solution for this concern. If the CD player is still inoperative technician will need to test the power and ground circuits. If no concern with power, ground, or connections, replace the Disc Player.
PIT5411C2017-08-15. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY. This Preliminary Information communication advises the technician that the Human Machine Interface, Radio or Tuner, radio controls, Integrated Center Stack, display, and Media Disc Players are placed on restriction through the General Motors Technical Assistance Center. Dealer will need to contact General Motors Technical Assistance Center for further assistance.
PIT5384A2017-08-15. Service bulletin. ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician about vehicles that may have the OnStar wireless fidelity inoperative. Technician will need to contact General Motors Technical Assistance Center with a scan tool connect to the vehicle for further assistance.
PIP4949E2017-08-15. Service bulletin. FUEL SYSTEM, OTHER:DELIVERY:FUEL PUMP; FUEL SYSTEM, OTHER:FUEL INJECTION SYSTEM; FUEL SYSTEM, OTHER:FUEL FILTER. This Preliminary Information communication provides information to the technician about vehicles that have a hard start or a no start. Technician may find Diagnostic Trouble Code DTCs P0087, P0088, P0191 or P128E. Technician will need to follow all Service Information diagnose for the Diagnostic Trouble Code. If the current Service Information diagnostic has led to Fuel Injection Pump replacement, Fuel Pressure Regulator 1 must be inspected for magnetic metal debris. If there is a questionable amount of magnetic debris found on Pressure Regulator 1 remove the Fuel Rail Pressure Sensor and/or Fuel Pressure Regulator 2 to inspect for magnetic metal debris. If technician will need to replace all of the parts listed under the latest version of PIP4949 found in the Service Forms section of Global Connect if debris is found. Clean and flush all fuel chassis lines, filter pipes, and other engine mounted fuel system pipes not replaced. Also the fuel filter housing must be cleaned with a new fuel filter installed. Then the fuel tank and fuel sender must be cleaned and flushed.
PIT5236D2017-08-15. Service bulletin. EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM). This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Technician will use Global Diagnostic System 2 to review the Firmware Over-the-Air version. If the Firmware Over-the-Air version on the scan tool equals 6708 the technician will need to contact General Motors Technical Assistance Center for further assistance. If the Firmware Over-the-Air version on the scan tool is lower than 6708 Dealer can order the part thought the Instrument Sales and Service website process.
PIP5130F2017-08-15. Service bulletin. ENGINE; EQUIPMENT ADAPTIVE/MOBILITY. This Preliminary Information communication provides information to the technician how to diagnose and repair a vehicle with an engine that runs with an intermittent crank no start with a Diagnostic Trouble Code P0011 or P00C6 current or history. The Camshaft Position Actuator Solenoid Valve may be sticking or binding causing the valve timing to be retarded. Dealer will need to cycle the Camshaft Position Actuator Solenoid Valve by energizing it using Global Diagnostic System 2.
PIP53572017-08-15. Service bulletin. ENGINE; EQUIPMENT ADAPTIVE/MOBILITY. This Preliminary Information communication provides information to the technician about vehicles with engine oil consumption. If published Service Information for oil consumption with no fix. Remove the vacuum line from the back of the vacuum pump and inspect for oil. If oil is found then reference the latest version of PIT5361.
PIP5228B2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR. This Preliminary Information communication provides information to the technician about vehicles that have a vibration that is felt between 1200 ? 1400 engine revolutions per minute when in active fuel management V4 mode. Technician will need to use J?38792-A Electronic Vibration Analyzer 2 or CH?51450-NVH Pico Oscilloscope Diagnostic Kit to measure the frequency of the vibration. Technician will need to remove and replace the exhaust muffler clamp that joins the three-way catalytic converter assembly to the pipe of the muffler assembly. After the exhaust is reinstalled remove and reinstall each cab mounts and retest.
PIP4932D2017-08-15. Service bulletin. ENGINE; EQUIPMENT ADAPTIVE/MOBILITY. This Preliminary Information communication provides information to the technician about vehicles with Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0101. Technician should follow published Service Information diagnostics for any Diagnostic Trouble Codes that are set. If during diagnosis the tech has found that the Airflow Leak Equivalency Ratio or Induction System Leak Indication is above or below the specification the tech will have to carefully check for leaks in the air intake.
PIT5344D2017-08-15. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.. This Preliminary Information communication advises the technician how to diagnose vehicles with the CD player inoperative. If this concern is encountered, cycle the CD player fuse and re-evaluate the concern. If the concern is no longer present, replace the CD player. When the CD player is still found to be inoperative after cycling the fuse follow Service Information diagnostics.
PIT54832017-08-15. Service bulletin. EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.. This Preliminary Information communication provides information to the technician about the compass on the radio display always shows North. Technician should update the radio with the latest calibrations.
PIT5353A2017-08-15. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; EQUIPMENT:ELECTRICAL; EQUIPMENT. This Preliminary Information communication provides information to the technician about what XM offerings are available for vehicles. A dealer or customer can access the website listed below for vehicle specific XM offerings and availability.
PIP5016B2017-08-15. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; ENGINE AND ENGINE COOLING; ENGINE AND ENGINE COOLING:ENGINE:DIESEL. This Preliminary Information communication provides additional information to the technician when replacing the Duramax Diesel head gasket. This is a supplement to procedure found in Service Information. The left and right cylinder head gaskets are not interchangeable and will block oil and coolant passages if installed incorrectly resulting in severe damage to the engine. Technician is not use any power sanding devices, wire brush or wheel as well as any chemical cleaning agents to clean the gasket surface. Leave the gaskets in the package until the surfaces are ready to install them. Do not set the gaskets on workbenches or tool boxes to avoid introduction of foreign debris. The cylinder head surface is not to be machined measure the head for warpage with a straight edge and feeler gauge replacing the head with warpage in excess of .1 millimeter. All M12 head bolts must be replaced however the M8 bolts can be reused. Install 2 head bolts secured at minimal torque to minimize the chance of introducing foreign material. Use a paint pen on the M12 bolts marking the head of each bolt indicating which of the 4 torque steps have been completed to prevent missing a step or doing a step twice.
PIP4864Q2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM; ENGINE AND ENGINE COOLING:ENGINE:DIESEL. This Preliminary Information communication provides information to the technician about vehicles that may have "Exhaust Fluid Low", "Exhaust Fluid Empty - Refill Now", "Exhaust Fluid Range: XXX" or "Service Exhaust Fluid - See Owners Now" on the Driver Information Center. If the technician is working on 2010 and 2011 model years campaign 11001 has now been released. Other vehicles technician will need to check the Body Control Module and the scan tool to insure the latest calibration are installed in both. Then use the scan tool to check Reductant System Data in the Engine Control Module. Ensure that all three diesel exhaust fluid level sensors are active with the diesel exhaust fluid tank level showing 100%. If the tank level is below 100% add up to 2 gallons of diesel exhaust fluid. After adding the fluid, use a scan tool to reset the reductant fluid tank level. When the reductant level warning shows "none" the diesel exhaust fluid system reset and reprogram is complete.
PIT5377C2017-08-15. Service bulletin. SERVICE BRAKES, HYDRAULIC. This Preliminary Information communication provides information to the technician on the step needed to diagnose and repair vehicles that may have uneven brake pad wear. Technician will need to inspect and measure the brake pads thickness. Also determine the customer?s driving style. The disc brake pads should only be replaced if the friction surface is worn to within?2.0?mm (0.079?in) of the mounting plates. The rotors and pads should be replaced with the updated part number If the pads are out of specification, perform normal Service Information diagnostics to determine the cause of the concern.
PIT4943D2017-08-15. Service bulletin. FUEL SYSTEM, GASOLINE; FUEL SYSTEM, OTHER:STORAGE:TANK ASSEMBLY; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL. This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0442. Technician will need to review Techlink article from May 2013 titled "Using the Evaporative Emissions System Tester" Technician will need to follow these steps to help diagnose the issue. First after the P0442 has been verified do not disturb any of the fuel system components. The technician now can use the scan tool to close the Evaporative Emissions System. If possible change the tank pressure sensor units from inch_H2O to milimeter_Hg for better resolution. Now the vehicle can be stared to monitor the tank pressure sensor output value for approximately two minutes. If the tank pressure sensor value does change, pressurize the fuel tank side of the purge solenoid with the GE 41413-A / J 41413-A and the necessary adaptors. Now add smoke and allow pressure to stabilize for 2 minutes. If smoke is allowed to pass through the purge solenoid, replace the purge solenoid. If the tank pressure sensor value does not change, then install CH-48096 adaptor between the purge line from the canister and the purge solenoid. With the Evaporative Emissions System closed, pressurize the system through the CH-48096 adaptor and allow the system to completely stabilize, by observing the Press / Vac Gauge for a minimum of 5 minutes. Now add smoke to the system with GE 41413-A / J 41413-A after system stabilization. Now inspect the purge solenoid, engine side, fuel cap, canister vent solenoid filter and any line quick connects. When the leak is unable to be located, test under a vacuum condition. his type of leak may be detected by using the scan tool Purge/Seal function to create a vacuum in the Evaporative Emissions System and then observe the FTP sensor parameter for vacuum decay.
PIP5234A2017-08-15. Service bulletin. FUEL SYSTEM, OTHER:FUEL INJECTION SYSTEM. This Preliminary Information communication advises the technician when Service Information diagnostics indicates a fuel injector may need to be removed for a repair or replaced the injector will need a new seal. This Preliminary Information contains all the O-ring seal and the injector kit part numbers.
PIP53452017-08-15. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; EQUIPMENT. This Preliminary Information communication provides information to the technician about being to achieve pre-load when setting up the pinion bearing pre-loads during reassembly of the 9.5/9.76 inch rear axles. Technician will need to use pinion gear install washer part number 11609638 onto the pinion shaft between the flange and nut. Tighten the pinion nut until you achieve 10 pound inch or 1.0 newton rotating torque. After the torque has been achieved back the nut off and remove the washer. Tighten the nut back down until you achieve 15 pound inch or 1.7 newton meters for used bearings or 20 pound inch 2.25 newton meters for new bearings.
PIC6034A2017-08-15. Service bulletin. EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.. This Preliminary Information communication provides information to the technician about vehicles that when shutting the vehicle off when the radio is turned off prior, the radio will turn back on in the muted condition on the next key cycle. No action should be taken at this time as this is considered a normal operating characteristic.
PIP5179B2017-08-15. Service bulletin. ENGINE; EQUIPMENT:MECHANICAL; FUEL SYSTEM, OTHER:FUEL INJECTION SYSTEM. This Preliminary Information communication provides information to the technician about vehicles that have extended or long crank time during cold ambient air temperatures. Direct Injection systems run at higher pressures, and the mechanical pump on the engine must build up the required pressure before the first injection event occurs. Direct Injection engines may have slightly longer cold crank times than that of port fuel engines.
PIP53412017-08-15. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; ENGINE. This Preliminary Information communication provides information to the technician about vehicles that engine runs and idles rough. Technician will find P0171 and or P0174. Technician will need to inspect the positive crankcase ventilation tube for a vacuum leak on the left side of the engine. Replace positive crankcase ventilation air tube and cover it with conduit to protect from repeat damage.
PIT5279C2017-08-15. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT:MECHANICAL; SEATS:FRONT ASSEMBLY:POWER ADJUST. This Preliminary Information communication provides information to the technician for vehicles that exhibit a driver?s power memory seat and power adjustable pedals inoperative. Look for poor terminal tension at the left instrument panel fuse block connector X1 terminals 27 and 28. If poor retention is found in these terminals replace them with terminated lead part number 19301761.
PIT5083A2017-08-15. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; VISIBILITY; STRUCTURE:BODY:DOOR. This Preliminary Information communication provides information to the technician about vehicles with the inside door panel material appearing to be pulling back from the door panel backing. Technician will check the windows for aftermarket window tint. Since this failure is not the result of a manufacturer defect, it would not be considered for coverage under a General Motors Warranty.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.