WenmarOpen by Wenmar Pro

Service bulletins for the 2014 Chevrolet Silverado

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

3313 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Only bulletins with component: Seats are shown. Show all

Bulletins, newest first
GCUS-3-8232018-04-02. Service bulletin. SEATS:FRONT ASSEMBLY:POWER ADJUST. 17018-Customer Satisfaction Program. Certain vehicles, equipped with power front passenger seat adjuster that was previously replaced, may have a condition in which the front passenger seat can be adjusted to a position beyond the occupant design travel range. Dealers will inspect front passenger seat tracks and, as necessary, install the seat stop(s).
PI1103E2017-12-22. Service bulletin. SEATS; ELECTRICAL SYSTEM. This preliminary informational bulletin provides a procedure for the technician to test the power seats, the outside power mirriors, shorts in the wiring and the MSM, and reprogram the module if shorts weren't found, for the customers concern of the mirriors and/or seat inoperative.
PI1091B2017-12-22. Service bulletin. SEATS. This preliminary informational bulletin provides repair information to correct a customer concern of warm air exhausting from driver and/or passenger front seat back into 2nd row seating area causing occupant discomfort.
PIC6179A2017-12-14. Service bulletin. SEATS. This Preliminary Information communication advises the technician that vehicles with front seat Regular Production Option Codes A52, AZ3, or B3F may comment about low treble, or excessive bass from the front door speakers. This is a normal design characteristic for this seat configuration. These vehicles lack a subwoofer.
PIT5434B2017-12-14. Service bulletin. SEATS. This Preliminary Information communication provides information to the technician only to provide additional tips when diagnosing a front heated seat concern and is not meant to be a diagnostic flow chart or replace Service Information. Always, perform and refer to Service Information for the latest diagnostic information and procedures.
PIT54342017-08-15. Service bulletin. SEATS; ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician only to provide additional tips when diagnosing a front heated seat concern and is not meant to be a diagnostic flow chart or replace Service Information. Always, perform and refer to Service Information for the latest diagnostic information and procedures. Trucks equipped with heated and cooled seats Regular Production Option Code (KB6), may comment on any of the following front heated seat concerns. Condition 1, a front heated seat (back and/or cushion) is inoperative. Technician should diagnosis each affected seat heater individually. Technician should test all four circuits Power, Ground, Control (from Body Control Module) and Heating Element Supply Power. The Power, Ground, Control (from Body Control Module) can easily be checked by starting the engine and turn on the cooled seat. When the cooled seats are turned on the blower in each seat back and cushion will turn on at that point technician will be able to hear the blower moving. The heating element supply power circuit can be test by disconnecting the affected heating element and connect a voltmeter across the heating element supply power and ground circuit. Then start the engine and turn on the heated seat, the blower will supply system voltage on the element supply power circuit for 1 to 2 seconds. With the heated seat element disconnected, use an ohmmeter to measure the resistance of the heating element. If all of the above steps check ok or the heating element resistance is close to the approximate spec, reconnect all disconnected connectors. Connect a voltmeter across the affected heated seat element connectors supply power and ground circuits back probing the connector. Then check the resistance of the heating element. The resistance should be close to the same resistance as when testing with the connector unplugged. Now check the voltage with the engine running and the heated sets on high. Condition 2, the front heate
PIT5279C2017-08-15. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT:MECHANICAL; SEATS:FRONT ASSEMBLY:POWER ADJUST. This Preliminary Information communication provides information to the technician for vehicles that exhibit a driver?s power memory seat and power adjustable pedals inoperative. Look for poor terminal tension at the left instrument panel fuse block connector X1 terminals 27 and 28. If poor retention is found in these terminals replace them with terminated lead part number 19301761.
PIT5434A2017-08-15. Service bulletin. ELECTRICAL SYSTEM; SEATS. This Preliminary Information communication provides information to the technician only to provide additional tips when diagnosing a front heated seat concern and is not meant to be a diagnostic flow chart or replace Service Information. Always, perform and refer to Service Information for the latest diagnostic information and procedures. Trucks equipped with heated and cooled seats Regular Production Option Code (KB6), may comment on any of the following front heated seat concerns. Condition 1, a front heated seat (back and/or cushion) is inoperative. Technician should diagnosis each affected seat heater individually. Technician should test all four circuits Power, Ground, Control (from Body Control Module) and Heating Element Supply Power. The Power, Ground, Control (from Body Control Module) can easily be checked by starting the engine and turn on the cooled seat. When the cooled seats are turned on the blower in each seat back and cushion will turn on at that point technician will be able to hear the blower moving. The heating element supply power circuit can be test by disconnecting the affected heating element and connect a voltmeter across the heating element supply power and ground circuit. Then start the engine and turn on the heated seat, the blower will supply system voltage on the element supply power circuit for 1 to 2 seconds. With the heated seat element disconnected, use an ohmmeter to measure the resistance of the heating element. If all of the above steps check ok or the heating element resistance is close to the approximate spec, reconnect all disconnected connectors. Connect a voltmeter across the affected heated seat element connectors supply power and ground circuits back probing the connector. Then check the resistance of the heating element. The resistance should be close to the same resistance as when testing with the connector unplugged. Now check the voltage with the engine running and the heated sets on high. Condition 2, the front heate
PIT54452017-08-15. Service bulletin. SEATS:FRONT ASSEMBLY:POWER ADJUST; ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician of addition information when diagnosing a service driver assist message with a diagnostic trouble code B172E and or a B172F. The haptic seat motor has a pigtail lead coming off of it. In many cases the wiring pigtail near the haptic seat motor has broken and will require replacement.
PIT54082017-08-15. Service bulletin. SEATS. This Preliminary Information communication advises the technician that some vehicles the haptic seat motors can be felt in the seat. Technician will access both haptic seat motors and rotate the motors flat, and then reinstall them back into the seat cushion. This will help improve the comfort of the seat cushion.
PIT5279B2017-08-15. Service bulletin. ELECTRICAL SYSTEM; SEATS. This Preliminary Information communication provides information to the technician for vehicles that exhibit a driver?s power memory seat and power adjustable pedals inoperative. Look for poor terminal tension at the left instrument panel fuse block connector X1 terminals 27 and 28. If poor retention is found in these terminals replace them with terminated lead part number 19301761.
G-1761772017-08-15. Service bulletin. SEATS; EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. 13310 - Service Update (bulletin cancelled). General Motors is cancelling Service Update Bulletin (SUB) 13310. After further investigation, it has been determined that some of the vehicles originally involved in SUB 13310 will not have the seatback condition. The following is an explanation of the status of vehicles involved in SUB 13310. Vehicles that may display the seatback condition, but have not had the repair in SUB 13310 performed, will be transferred to Noncompliance Recall 13323. These VINs will show a closed status for SUB 13310 in IVH on October 3, 2013. Vehicles that were built prior to August 1, 2013, will not have the seatback condition. These vehicles will not be transferred to Noncompliance Recall 13323 and will show as closed in IVH October 8, 2013, which will allow dealers to submit warranty transactions on vehicles that have already been repaired. Do not repair any additional vehicles under SUB 13310.
G-1760292017-08-15. Service bulletin. SEATS. 13310A - Service Update (revised inspection procedure). This bulletin provides a service procedure to inspect and, if necessary, adjust the seatback recliner mechanism. On some of these vehicles, either front seat may display seatback movement.
G-1756852017-08-15. Service bulletin. SEATS. 13310 - Service Update. This bulletin provides a service procedure to adjust the seatback recliner mechanism, if necessary, on certain vehicles, equipped with a manual reclining seatback. On some of these vehicles, either front seat may display seatback movement.
PI1183A2017-08-15. Service bulletin. SEATS:FRONT ASSEMBLY:POWER ADJUST. This preliminary informational bulletin provides repair information for a customer concern of front seat lateral movement and/or click type noise while driving.
PIT5380B2017-08-15. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; SEATS:FRONT ASSEMBLY:RECLINER. This Preliminary Information communication provides information to the technician about vehicle that may have a front driver's or passenger's seat back may lean or be turned outward. Technician will need to remove the seat bottom trim cover and reinstall it completely and squarely to the cushion to correct the concern.
PIT55422017-08-15. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; SEATS. This Preliminary Information communication provides information to the technician about vehicles that have an excessive lateral driver or passenger seat movement and/or a clunk/click/pop type feeling or noise. Technician will need to install a front seat lateral retainer. Technician will need to remove plastic material from the top side of the guide end of the lateral retainer to enable installation.
PIT52232017-08-15. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; SEATS. This Preliminary Information communication provides information to the technician about vehicles that have front driver?s or passenger?s seat cover/cushion is loose. Technician will need to install U-clips to help secure the cover to the seat frame.
PIT52222017-08-15. Service bulletin. SEATS; ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician about vehicles that have the Center Seat Accessory Power Outlet (X80E) is inoperative. Technician will need to inspect for a short to ground on circuit 850 near the left pivot for the center seat armrest.
PIT52402017-08-15. Service bulletin. EQUIPMENT:APPLIANCE:AIR CONDITIONER; SEATS:FRONT ASSEMBLY:SEAT HEATER/COOLER. This Preliminary Information communication provides information to the technician about customer's questions on what temperature the heated and/or cooled seats will turn on during a remote vehicle start. Dealer should advise the customer that the heated seats will turn on when ambient temperature is below 50 degrees Fahrenheit (10 degrees Celsius) and the cooled seats will turn on when ambient temperature is above 80 degrees Fahrenheit (27 degrees Celsius).
PIT5240A2017-08-15. Service bulletin. SEATS:FRONT ASSEMBLY:SEAT HEATER/COOLER; EQUIPMENT:APPLIANCE:AIR CONDITIONER. This Preliminary Information communication provides information to the technician about systems operate during a remote vehicle start event. Dual Zone Auto Regular Production Option Code (CJ2) Heater-Vent-Air Conditioning settings the Heater-Vent-Air Conditioning settings will remain set to the previous Heater-Vent-Air Conditioning settings when the ignition was turned off. Single Zone Manual Regular Production Option Code (C67) HVAC settings the Heater-Vent-Air Conditioning settings will remain set to the previous Heater-Vent-Air Conditioning settings when the ignition was turned off. The Rear window defogger during a remote start event, the rear window defogger will turn on if the outside temperature is 44 degrees Fahrenheit (7 degrees Celsius) or below. The heated seats will not turn on if a Remote Vehicle Start event is performed within 2 hours of shutting the engine off. The cooled seats will turn to the high setting when the ambient temperature is above 80 degrees Fahrenheit (27 degrees Celsius). Heated steering wheel will not turn on during Remote Vehicle Start event.
06-08-50-009I2017-08-15. Service bulletin. SEATS; SEATS:FRONT ASSEMBLY:SEAT HEATER/COOLER; AIR BAGS:SENSOR:OCCUPANT CLASSIFICATION. This informational bulletin provides Information on Passenger Presence Sensing System (PPS or PSS) Concerns with Custom Upholstery, Accessory Seat Heaters or Other Comfort Enhancing Devices
PIT5215A2017-08-15. Service bulletin. SEATS:FRONT ASSEMBLY:SEAT HEATER/COOLER. This Preliminary Information communication provides information to the technician about vehicles that after installing the GM Accessory Heated Seat Kit, one or more of the following issues may be present the heated seat back and/or bottom turns off after approximately 30 seconds and after turning on the heated seat switch, the indicators remain on, but the seat is not heating. Technician may find Diagnostic Trouble Codes B1935 Sym 0E, B2180 Sym 0E, B2425 Sym 0D, and/or B2430 Sym 0D. Technician will need to inspect the accessory heated seat wiring harness and make sure the heater element connectors are installed correctly.
PIT4323G2017-08-15. Service bulletin. SEATS. This Preliminary Information communication provides information to the technician about the passenger presence system, passenger air bag on/off indicators, passenger air bag on/off switch, and passenger seat belt indicator. Dealer can review and explain the options that are equipped with the vehicle in question.
142812017-02-01. Service bulletin. SEATS; ELECTRICAL SYSTEM. 14281 - CUSTOMER SATISFACTION PROGRAM. CERTAIN 2014-2015 MODEL YEAR CHEVROLET SILVERADO, SUBURBAN, AND TAHOE MODEL VEHICLES AND 2014-2015 MODEL YEAR GMC SIERRA AND YUKON MODEL VEHICLES EQUIPPED WITH A DEALER INSTALLED REAR ENTERTAINMENT SYSTEM MAY HAVE A CONDITION IN WHICH THE REAR SEAT ENTERTAINMENT SYSTEM IN VEHICLES WAS RELEASED AS A DEALER ACCESSORY BEFORE FINAL GENERAL MOTORS VALIDATION APPROVAL. VALIDATION APPROVAL AT GM REQUIRES VERY RIGOROUS TESTING PRIOR TO RELEASE, WHICH, IN MANY CASES, GOES BEYOND WHAT IS REQUIRED TO COMPLY WITH GOVERNMENTAL SAFETY STANDARDS. THESE VEHICLES, AS EQUIPPED, STILL MEETS ALL FEDERAL MOTOR VEHICLE SAFETY STANDARDS. DEALERS ARE TO REMOVE AND REPLACE THE HINGED SCREEN STYLE REAR SEAT ENTERTAINMENT SYSTEM, WITH A REVISED SYSTEM FEATURING AN INTEGRAL SCREEN.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.