WenmarOpen by Wenmar Pro

Service bulletins for the 2007 Chevrolet Silverado

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

1617 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Only bulletins with component: Electrical system are shown. Show all

Bulletins, newest first
PIT4813F2017-12-22. Service bulletin. ELECTRICAL SYSTEM; ELECTRICAL SYSTEM:12V/24V/48V BATTERY. This Preliminary Information communication provides information to the technician about vehicles with a "Service Charging System" message displayed on the Driver Information Center and/or a low voltage reading on the volt gauge during the first several minutes after a cold start. Technician may find a Diagnostic Trouble Code B15517 sym 03. If this concern only occurs during the first several minutes of a cold start, no repairs should be made. Dealer should communicate to the customer that this is normal operating characteristic of vehicles equipped with the diesel engine.
PIP4401E2017-12-22. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT. This Preliminary Information communication provides information to the technician about vehicles that may have the check engine light, tow/haul, Supplemental Inflatable Restraint, cruise control or other various indicators or warning lamps will not come on in the instrument panel. Tech will need to the Tech 2 scan tool to command the instrument panel indicator lights on. If the light do not turn on technician should inspect (AUX HVAC) 10 amp fuse in the under-hood fuse block for open or high resistance.
PIT5209A2017-12-22. Service bulletin. ELECTRICAL SYSTEM; BACK OVER PREVENTION: BACK-UP ALARM; BACK OVER PREVENTION; STRUCTURE. This Preliminary Information communication provides information to the technician about vehicles that for no reason the alarm will go active. Technician will need to use a scan tool to verify that the alarm was activated by the inclination sensor. If the trigger is the inclination sensor, inspect the sensor's mounting location. Technician will need to relocate the sensor if it is attached to the driver's side lower Heater-Vent-Air Conditioning duct. Technician will need to reinstall the sensor to the top of the Body Control Module bracket.
PIP4379L2017-12-22. Service bulletin. POWER TRAIN; ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician about vehicles that have not engagement into drive, delayed, no engagement into reverse, and or a range inhibit. Technician may find Diagnostic Trouble Codes P0701, P0731, P0732, P0733, P0734, P0736, P0751, P0756, P0761, P0776, P0843, P0848, P0873, P0877, P0894 or P2723. Technician should follow published Service Information diagnostics for Diagnostic Trouble Code P0701 first. Technician will also ensure the fluid level is at the top of the hot band when the transmission fluid temperature is 175° Fahrenheit. Diagnostic Trouble Codes P0701, P0731, P0732, P0733, P0734, P0736, P0751, P0756, P0761, P0776, P0843, P0848, P0873, P0877, P0894 or P2723 can set by the following fluid service/filter change, transmission service involving removing the pan, low fluid level caused by leaks, or after long periods of storage. If the fluid level has been properly checked using the HOT check procedure listed in Service Information document 2408059 and any of the Diagnostic Trouble Codes reset during a cold start inspect the internal suction filter for possible cracks. If no other concerns are found inspect for a stuck lube regulator valve in the pump cover due to debris.
PIT4730B2017-12-14. Service bulletin. ELECTRICAL SYSTEM. This Preliminary Information communication a diagnostic tip if the high speed lan bus is shorted to ground, which can cause the BCM to appear off line.
PIC3100F2017-12-14. Service bulletin. ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL. This Preliminary Information communication provides information to the technician about vehicle's odometer appears to be inaccurate relative to a known distance traveled. Technician should obtain a hand-held GPS unit to test the odometer. If a hand held GPS unit is not available, the only other option is to verify the miles traveled using a surveyor's wheel or a dynamometer.
PIC5650C2017-11-14. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
PIT5353B2017-11-14. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM; EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.. This Preliminary Information communication provides information to the technician about what XM offerings are available for vehicles. A dealer or customer can access the website listed below for vehicle specific XM offerings and availability.
PIT5236H2017-10-15. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Technician will use Global Diagnostic System 2 to review the Firmware Over-the-Air version and the OnStar Customer Identifier and contact General Motors Technical Assistance Center for further assistance.
PIP54292017-10-15. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. This Preliminary Information communication advises the technician that the customer may experience a 2-3 slip or flare after the vehicle has been sitting for a period of time. Technician can update the Transmission Control Module if working on a model year 2007. On all other model years dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle.
PI0639D2017-10-15. Service bulletin. ELECTRICAL SYSTEM. This preliminary bulletin provides a procedure to install adhesive back stock to the electrical connector for the steering wheel position sensor, to eleminate the excessive clearance/movement that causes the connector to loose contact and turns the Service Stabilitrak message on.
07-08-49-020K2017-10-15. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. This informational bulletin explains the programming method quick reference guide for the IPC Odometer.
PI0592C2017-10-15. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. This preliminary bulletin provides information on Service Programming System (SPS) Errors (E4398, E4399, E4403, E4404, E4413, E4414, E4423 or E4491).
07-08-42-006G2017-10-12. Service bulletin. ELECTRICAL SYSTEM; EXTERIOR LIGHTING. This informational bulletin provides information on Available BCM Calibrations to Restore Bulb Outage Detection on Vehicles Produced by a Second Stage Manufacturer (Upfitter), Turn Signals Flash Fast after Factory Box Removed
PIC5588D2017-10-04. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. This Preliminary Information communication provides information to the technician on the programming and activation of the OnStar system. For many 2008 and prior model year GM vehicles, the programming is performed using the Tech 2 and the activation is initiated by a Service Programming System. For the 2010 and UP model year vehicles, the OnStar set-up procedure and OnStar Activation request have been combined into a single programming event called OnStar Set-up and Activation in Service Programming System.
08-08-44-015F2017-08-31. Service bulletin. ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL; EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.. This informational bulletin provides Information on Inappropriate Warranty Claims Submitted for Damaged Radios and Instrument Panel Clusters (IPCs)
07-07-30-010D2017-08-31. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. This informational bulletin provides explanation on how to take snapshot data with a Tech 2 and upload it to a computer and where to email the info to.
07-08-49-020L2017-08-31. Service bulletin. ELECTRICAL SYSTEM. This informational bulletin provides information for the IPC odometer programming method quick reference guide.
03-08-46-004S2017-08-31. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. This informational bulletin provides information on OnStar® VCIM is currently restricted parts. By working closely with our dealers and technicians, through the part restriction process, the General Motors team will gain a better understanding of any field concerns that may develop.
DOR-K5Y9W-112017-08-25. Service bulletin. ELECTRICAL SYSTEM; AIR BAGS. All applicable vehicle applications are without Electronic Accessory Control System option. This communication is to return unsold inventory because some product sold in 2016 may not have coil harness wound in a centered condition as an assembly aid. If installer does not center the rotations of the assembly during replacement process in accordance with applicable AllData service and repair procedure, post-install turning of the steering wheel will trigger the air bag warning light of the vehicle.
PIC6140A2017-08-15. Service bulletin. ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician about vehicles that has a red LED and DTC B2455 setting current in the Vehicle Communication Interface Module after performing Canada upgrade. Technician will need to gain access to the Vehicle Communication Interface Module. After gaining access to the Vehicle Communication Interface Module pull the tape back on the X2 connector then tape the bare wires individually to prevent them from shorting.
PIC61072017-08-15. Service bulletin. ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician about being unable to receive OnStar ?Over The Air? updates. Technician will need to press the OnStar button and verify they have an active account and that the call connects with data and location.
PIT5384A2017-08-15. Service bulletin. ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician about vehicles that may have the OnStar wireless fidelity inoperative. Technician will need to contact General Motors Technical Assistance Center with a scan tool connect to the vehicle for further assistance.
PIC61012017-08-15. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT ADAPTIVE/MOBILITY. This Preliminary Information communication provides information to the technician about vehicles that are unable to receive OnStar Hands Free Calling calls and or the OnStar center is unable to perform remote services. Technician will need to push the OnStar Blue button and verify the system successfully connects to an advisor. Place an outbound personal call from the vehicle and verify it connects. Place an inbound call to the vehicle making sure to dial using the 11 digit phone number (1 + area code + number). If outbound calls can be placed and only incoming calls fail. Cycle power to the Vehicle Communication Interface Module and retest inbound call to the vehicle. If the power cycle corrects the concern and the module manufacturer is continental, replace the Vehicle Communication Interface Module. If the power cycle corrects the concern and the module manufacturer is LG, please record information from the latest version of PIC4310 and call General Motors Technical Assistance Center for further assistance. If the concern is still present after the power cycle, please record information from the latest version of PIC4310 and call General Motors Technical Assistance Center for further assistance.
PIC6140B2017-08-15. Service bulletin. ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician about vehicles that has a red LED and DTC B2455 setting current in the Vehicle Communication Interface Module after performing Canada upgrade. Technician will need to gain access to the Vehicle Communication Interface Module. After gaining access to the Vehicle Communication Interface Module pull the tape back on the X2 connector then tape the bare wires individually to prevent them from shorting.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.