WenmarOpen by Wenmar Pro

Service bulletins for the 2013 Cadillac XTS

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

2094 on file from NHTSA, as of 2026-10-19.

About P0300 on the 2013 Cadillac XTS: what the code means, and the bulletins and recalls about the same components.

By type

By component

By trouble code

By topic

Only bulletins with trouble code: P0300 are shown. Show all

Bulletins, newest first
18-NA-1152024-08-14. Service bulletin. ENGINE. This service bulletin provides inspection/diagnosis/correction information on a cold start misfire and/or rough idle and DTC P0300 that may also be set.
PIP5628G2023-09-18. Service bulletin. ENGINE. This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
PIP5628F2023-05-15. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:ENGINE CONTROL MODULE (ECU/ECM). This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
PIP5628E2023-03-13. Service bulletin. EQUIPMENT:ELECTRICAL:ACCESSORY GENERATOR:OUTLETS/RECEPTACLE. This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
18-NA-1152022-05-11. Service bulletin. ENGINE AND ENGINE COOLING. This service bulletin provides inspection/diagnosis/correction information on a cold start misfire and/or rough idle and DTC P0300 that may also be set.
PIP5628E2022-01-24. Service bulletin. ENGINE AND ENGINE COOLING. This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
PIP5628C2020-11-16. Service bulletin. ENGINE AND ENGINE COOLING. This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
18NA1152020-10-26. Service bulletin. ENGINE AND ENGINE COOLING. This Bulletin provides inspection/diagnosis/correction information on a cold start misfire and/or rough idle and DTC P0300 that may also be set.
PIP5628B2020-06-15. Service bulletin. ENGINE. This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
PIP56282019-03-11. Service bulletin. ENGINE AND ENGINE COOLING. This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
PIP4959F2018-05-21. Service bulletin. ENGINE AND ENGINE COOLING. This Preliminary Information communication provides information to the technician with information regarding high misfire rates always on #1 cylinder. A customer may complain of misfires or roughness on cold start up with a P0300 diagnostic trouble code. Technician is to add coolant dye to the system and run the engine through warm up to circulate the dye. Pressurize the cooling system after a cold soak and inspect the cylinder with a bore scope for coolant dye. Dye is used to identify coolant over residual fuel being that might be left in the cylinder. The technician is not to replace the cylinder head as it will not correct this concern. In some cases it is necessary to remove the head for inspection. Do not replace the engine for small surface pock marks or a pitting appearance this is normal and do not connect to coolant passages. Usually if porosity is present there will be a break in the carbon ring. Only replace the engine if true porosity is found. Technician is to call Product Quality Center with the latest version of bulletin 02-07-30-029 if porosity is found and engine replacement is required.
18NA1152018-05-21. Service bulletin. ENGINE AND ENGINE COOLING. This Bulletin provides inspection/diagnosis/correction information on a cold start misfire and/or rough idle and DTC P0300 that may also be set.
PIP4959G2018-01-16. Service bulletin. ENGINE AND ENGINE COOLING. This Preliminary Information communication provides information to the technician with information regarding high misfire rates always on #1 cylinder. A customer may complain of misfires or roughness on cold start up with a P0300 diagnostic trouble code. Technician is to add coolant dye to the system and run the engine through warm up to circulate the dye. Pressurize the cooling system after a cold soak and inspect the cylinder with a bore scope for coolant dye. Dye is used to identify coolant over residual fuel being that might be left in the cylinder. The technician is not to replace the cylinder head as it will not correct this concern. In some cases it is necessary to remove the head for inspection. Do not replace the engine for small surface pock marks or a pitting appearance this is normal and do not connect to coolant passages. Usually if porosity is present there will be a break in the carbon ring. Only replace the engine if true porosity is found. Technician is to call Product Quality Center with the latest version of bulletin 02-07-30-029 if porosity is found and engine replacement is required.
PIP4959E2017-08-15. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL; ENGINE AND ENGINE COOLING. This Preliminary Information communication provides information to the technician with information regarding high misfire rates always on #1 cylinder. A customer may complain of misfires or roughness on cold start up with a P0300 diagnostic trouble code. Technician is to add coolant dye to the system and run the engine through warm up to circulate the dye. Pressurize the cooling system after a cold soak and inspect the cylinder with a bore scope for coolant dye. Dye is used to identify coolant over residual fuel being that might be left in the cylinder. The technician is not to replace the cylinder head as it will not correct this concern. In some cases it is necessary to remove the head for inspection. Do not replace the engine for small surface pock marks or a pitting appearance this is normal and do not connect to coolant passages. Usually if porosity is present there will be a break in the carbon ring. Only replace the engine if true porosity is found. Technician is to call Product Quality Center with the latest version of bulletin 02-07-30-029 if porosity is found and engine replacement is required.
PIP5062B2017-08-15. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; ENGINE. This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that have check engine light and a misfire. Technician will find a P0300 set. If the misfiring cylinder is creating NO or very low power, technician will need to follow these diagnostics steps. 1) Swap the ignition coil and spark plug with another cylinder. 2) Inspect the plug when out for wet or dry condition. 3) Perform an injector test with a scan tool. 4) If the plug is wet then check for a leaking or stuck open injector. 5) If the plug is dry then enrich the intake air with propane. If the severity of the misfire is less with enrichment, suspect a weak or inoperative injector driver in the Engine Control Module and replace as needed. 6) Perform a cylinder leakage test to determine if there is a valve sealing concern. If there is a valve sealing concern see the latest version of PIP5029 for recommendations.
PIP5062A2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING; ELECTRICAL SYSTEM:IGNITION. This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that have check engine light and a misfire. Technician will find a P0300 set. If the misfiring cylinder is creating NO or very low power, technician will need to follow these diagnostics steps. 1) Swap the ignition coil and spark plug with another cylinder. 2) Inspect the plug when out for wet or dry condition. 3) Perform an injector test with a scan tool. 4) If the plug is wet then check for a leaking or stuck open injector. 5) If the plug is dry then enrich the intake air with propane. If the severity of the misfire is less with enrichment, suspect a weak or inoperative injector driver in the Engine Control Module and replace as needed. 6) Perform a cylinder leakage test to determine if there is a valve sealing concern. If there is a valve sealing concern see the latest version of PIP5029 for recommendations.
PIP4959C2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING:COOLING SYSTEM; ENGINE AND ENGINE COOLING. This Preliminary Information communication provides information to the technician with information about vehicles that misfires or roughness on cold start up. Technician may find Diagnostic Trouble Code P0300 set. Technician will need to add coolant dye to the system and run the engine through warm up to circulate the dye. Pressurize the cooling system after a cold soak and inspect the cylinder with a bore scope for coolant dye. If coolant is found in the cylinder technician will need to contact General Motors Product Quality Center for engine replacement.
PIP4959D2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING:COOLING SYSTEM. This Preliminary Information communication provides information to the technician with information regarding high misfire rates always on #1 cylinder. A customer may complain of misfires or roughness on cold start up with a P0300 diagnostic trouble code. Technician is to add coolant dye to the system and run the engine through warm up to circulate the dye. Pressurize the cooling system after a cold soak and inspect the cylinder with a bore scope for coolant dye. Dye is used to identify coolant over residual fuel being that might be left in the cylinder. The technician is not to replace the cylinder head as it will not correct this concern. In some cases it is necessary to remove the head for inspection. Do not replace the engine for small surface pock marks or a pitting appearance this is normal and do not connect to coolant passages. Usually if porosity is present there will be a break in the carbon ring. Only replace the engine if true porosity is found. Technician is to call Product Quality Center with the latest version of bulletin 02-07-30-029 if porosity is found and engine replacement is required.
PIP5062C2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING; ELECTRICAL SYSTEM:IGNITION. This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that have check engine light and a misfire. Technician will find a P0300 set. If the misfiring cylinder is creating NO or very low power, technician will need to follow these diagnostics steps. 1) Swap the ignition coil and spark plug with another cylinder. 2) Inspect the plug when out for wet or dry condition. 3) Perform an injector test with a scan tool. 4) If the plug is wet then check for a leaking or stuck open injector. 5) If the plug is dry then enrich the intake air with propane. If the severity of the misfire is less with enrichment, suspect a weak or inoperative injector driver in the Engine Control Module and replace as needed. 6) Perform a cylinder leakage test to determine if there is a valve sealing concern. If there is a valve sealing concern see the latest version of PIP5029 for recommendations.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.