WenmarOpen by Wenmar Pro

Service bulletins for the 2018 Cadillac Escalade

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

1129 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Only bulletins with component: Backup camera are shown. Show all

Bulletins, newest first
PIP5395G2023-08-21. Service bulletin. BACK OVER PREVENTION; FUEL SYSTEM, GASOLINE. This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that may have rattle or ticking noise that is louder inside the vehicle than outside. The noise may also sound like a lifter tick. If the noise is heard best at the fuel line and the sound will be real loud with a stethoscope. The fuel line will need to be replaced.
17-NA-3312023-02-28. Service bulletin. BACK OVER PREVENTION; EQUIPMENT. This informational bulletin provides information to the customer about the rear camera guidelines not being present at times due to the VBM taking over the rear camera option.
070601016G2022-06-13. Service bulletin. BACK OVER PREVENTION. This informational bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.
17-NA-3312021-04-15. Service bulletin. BACK OVER PREVENTION: SENSING SYSTEM: CAMERA; EQUIPMENT; EQUIPMENT ADAPTIVE/MOBILITY. Rear View Camera Guidelines Not Present at Times Condition Some customers may report that the Rear View Camera (RVC) guidelines are temporarily not available at times but the RVC will remain on during the concern. Additionally, no related DTCs will be found if this bulletin applies. One example of when this concern may be observed is if a customer quickly starts the car and immediately places the shifter in Reverse while the infotainment system is still in the initial boot up process. Cause This is a result of the RVC image being provided via an alternate robust RVC feed from the Video Bypass Module (NGI systems) or from the radio (BYOM2 and Info 3.0 systems). This alternate robust RVC feed is provided in the event that the primary RVC feed is not available for any reason just to ensure that the RVC image is always present when in reverse. Correction If this concern is experienced and no related codes are present, DO NOT replace any parts as it is normal for the RVC guidelines not to be present when the RVC image being displayed is from the alternate robust RVC feed. If this occurs after quickly starting the vehicle and immediately placing the shifter in Drive, the RVC guidelines can be displayed again in most cases if they are really needed by safely coming to a stop, placing the transmission in Park for a moment, and then shifting to Reverse again.
PIC6086G2021-01-25. Service bulletin. VISIBILITY; BACK OVER PREVENTION. This Preliminary Information communication provides the technician with steps to resolve the issue of an oily substance that may be found on the inside windshield surface, and appears to be leaking from the rear view mirror area. Technician will remove the moisture sensor and clean the glass and mounting bracket with alcohol wipe. If the gel separates from the sensor the sensor will need to be replaced.
PIC64242021-01-25. Service bulletin. AIR BAGS; BACK OVER PREVENTION:SOFTWARE. This Preliminary information communicates a condition where there is only newer hardware available when replacing the Active Safety Control Module. The newer hardware is not compatible with whatis currently loaded into the SPS programming system. Engineering is working on a new software set to address the concern.
150601002I2020-04-27. Service bulletin. BACK OVER PREVENTION; ENGINE. This technical bulletin provides a procedure to repair the valve lifter oil manifold and/or lifters to correct the customers concern of engine misfire, ticking noise and/or MIL Illuminated.
PIT5622A2019-08-12. Service bulletin. BACK OVER PREVENTION. This Preliminary information communicates instructions dealer to inspect for a broken or damaged side objector sensor/module bracket if there is a "Side Detection System Unavailable" message displayed at startup.
PIT5441C2019-04-08. Service bulletin. SERVICE BRAKES; EQUIPMENT; BACK OVER PREVENTION: SENSING SYSTEM: CAMERA; PARKING BRAKE; EQUIPMENT ADAPTIVE/MOBILITY; EQUIPMENT:ELECTRICAL; LANE DEPARTURE. This Preliminary Information communication provides information to the technician the steps to diagnose and repair vehicles that may have an Object Detection System Message Diagnostic Trouble Codes U0075, U026A, U026B, U026C, U0265, U0268, and/or U0269 stored in the active safety module. Technician should inspect his Multiple Diagnostic Interface cable for damage. Technician should use the Multiple Diagnostic Interface on a like vehicle with object detection bus or theEL-47955-1 MDI 1, MDI 2 Self-Test Loopback Adapter,if there are no issues found finish with diagnosing the customer’s concern, if concern is present in the like vehicle replace the Multiple Diagnostic Interface cable.
PIT5552C2019-03-11. Service bulletin. BACK OVER PREVENTION: SENSING SYSTEM: CAMERA. This Preliminary information communicates repair information for the rear vision camera or surround vision camera image being: - Yellow - Blurry - Distorted - Image scrolling - Image with NO gridlines - Screen is blue with gridlines - Screen is blue with Service Rear Vision System message
17NA3752018-06-04. Service bulletin. BACK OVER PREVENTION: SENSING SYSTEM: CAMERA. This informational bulletin provides a diagnostic tip for rear vision camera image that is grainy, distorted and/or pixelated
PIT5507D2018-05-21. Service bulletin. BACK OVER PREVENTION: WARNINGS. This Preliminary Information communication provides information to the technician about vehicles that may have a diagnostic trouble code U0159 set in the instrument panel cluster and /or the body control module. For vehicles equipped with Ultrasonic Park Assist System Regular Production Option Code UD5 or UD7 technician will use Service Programming System to reprogram the Parking Assist Control Module to correct this concern. Technician will need to inspect the front park assist sensors scallops/reliefs molded into the ring if previously replaced. Technician will need to replace the sensor rings with part number 84075328.
17NA3312018-04-23. Service bulletin. BACK OVER PREVENTION: SENSING SYSTEM: CAMERA. This informational bulletin provides information to the customer about the rear camera guidelines not being present at times due to the VBM taking over the rear camera option.
PIT5552B2018-03-12. Service bulletin. BACK OVER PREVENTION: SENSING SYSTEM: CAMERA. This Preliminary information communicates repair information for therear vision camera or surround vision camera image being: - Yellow - Blurry -Distorted - Image scrolling - Image with NO gridlines - Screen is blue with gridlines - Screen is blue with Service Rear Vision System message
PIP5446A2018-02-21. Service bulletin. BACK OVER PREVENTION. This Preliminary Information communication provides information to the technician about vehicles that have a Harsh Shift 1/2 and 2/3 and Sputter Applying Throttle Between 0 and 30%, Rough idle. Technician may find Diagnostic Trouble Codes P0101, P0171, P0172, P0174, and or P0175. Technician should inspect for cast flashing near the Mass Air Flow sensor as seen below.
PIP5168F2018-02-21. Service bulletin. POWER TRAIN:AXLE ASSEMBLY:AXLE SHAFT; BACK OVER PREVENTION; FUEL SYSTEM, GASOLINE. This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have a no crank concern. Technician will need to check the valve train for movement when the engine is cranked. If the valve train is not moving while the crankshaft is moving the front cover will need to be removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly. If the valve train is rotating during inspection, disconnect the Camshaft Position sensor and check if the engine will start. If the engine starts front cover will need to be removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly. If the engine does not start with the Camshaft Position sensor disconnected the follow published “Engine Cranks But Does Not Run” diagnosis in Service Information. Also perform an Engine Compression Test and Cylinder Leakage Test in Service Information documents all results. If the Service Information procedures above isolate an engine mechanical concern then removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.