WenmarOpen by Wenmar Pro

Service bulletins for the 2010 BMW X6

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

278 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Bulletins, newest first
1607122018-12-03. Service bulletin. FUEL SYSTEM, DIESEL:STORAGE:TANK ASSEMBLY. Service Action: Replace the Left and Right Fuel Level Sensor. After refueling, the fuel gauge will display an incorrect fuel level. When this occurs, the fuel gauge shows the fuel level as 3/4 full. CAUSE Due to a high proportion of ethanol in the fuel, the internal mechanisms of the fuel level sensors may swell. This may inhibit the movement of one or both of the fuel level sensors.
6515122018-12-03. Service bulletin. EQUIPMENT. "Service Action: CIC - Install Navigation Road Map Database 2013. Before delivering affected vehicles to the customer, the Car Information Computer (CIC) road map database 2013 must be installed onto the CIC internal Hard Disc Drive (HDD). Note: The INITIAL enabling code ""FSC CIC map, N. America 2013 INITIAL"" is necessary to start the installation process and to activate the road map database."
6113052018-12-03. Service bulletin. ELECTRICAL SYSTEM. "Discharged Battery: Energy Diagnosis Must Be Performed. The electrical system of BMW vehicles has been subject to an ongoing development process over the last few years. This has led to increased demands being placed on the battery. This document covers important information for the dealer on how to handle ""discharged battery"" complaints. A discharged battery can have various causes, most of which do not concern the battery itself. A failed battery is often the symptom and not the cause. A fully serviceable battery fails when an electrical component causes the battery to discharge; the battery becomes internally damaged and must be replaced. For more information, refer to www.batteryuniversity.com/parttwo-42B.htm For this reason, replacing the battery is not usually a permanent repair. The cause of the discharged battery must be analyzed in order to guarantee a proper repair. In order to properly repair the vehicle the first time in the workshop, it is very important that the diagnostic test plans are performed to completion with all results taken into to consideration. The procedure as outlined below contains information that will guide the technician into properly repairing the vehicle and getting paid for a warranty claim. CAUSE Refer to the ""Procedure"" section of this Service Information for details."
5117122018-12-03. Service bulletin. STRUCTURE. Service Action: Install Door Sill Trim Strips. The door sill trim strips were not installed.
3101122018-12-03. Service bulletin. POWER TRAIN. Clicking Noise from Front Axle. Clicking noises are heard from the front axle area while maneuvering at low speeds (e.g., parking lot maneuvers). CAUSE Movement between the contact surfaces of the wheel bearing and swivel bearing (knuckle)
1607122018-12-03. Service bulletin. FUEL SYSTEM, DIESEL:STORAGE:TANK ASSEMBLY. Service Action: Replace the Left and Right Fuel Level Sensor. After refueling, the fuel gauge will display an incorrect fuel level. When this occurs, the fuel gauge shows the fuel level as 3/4 full. CAUSE Due to a high proportion of ethanol in the fuel, the internal mechanisms of the fuel level sensors may swell. This may inhibit the movement of one or both of the fuel level sensors.
1306122018-12-03. Service bulletin. FUEL SYSTEM, GASOLINE. "N63 and N74 Engine: ISTA/D 2.33 Diagnostic Error in the Low-pressure Fuel Supply Sensor Value. INFORMATION When diagnosing the low-pressure fuel supply sensor with one of the following test plans and ISTA/D 2.33, an error will be encountered in the display. The value of the low-pressure fuel supply sensor will read 0 bar at all times. * B1214_DI6KNDR * D18KHDR * AT1214_DIKNDR * AT1214_DIKHDR Do not replace the low-pressure fuel supply sensor. The operating pressure of the low-pressure fuel supply sensor can found in ""DME Diagnostic Query"" using the following procedure: 1. Exit the test plan and return to the control unit tree. http://www.bmwtis.net/tiscode/cgi-bin/omcgi.exe?sie_path=/tsb/bulletins/htm_store/14907...11/7/2012 Page 2 of 2 2. Select ""DME"" in the control unit tree. 3. Select "" Call Up ECU Functions."" 4. Select ""Diagnostic Query."" 5. Select ""Fuel Pressure (Low Pressure)."" 6. Select ""Query Status."" The engine must be running to verify operation of the pressure sensor. The software error will be corrected in ISTA/D 2.34, scheduled for release in December 2012. "
1307122018-12-03. Service bulletin. FUEL SYSTEM, GASOLINE. N63 and S63 Engine: High-pressure Fuel Injector Replacement Procedures. The customer complains that one of the following scenarios has been encountered while operating the vehicle: * During a cold start in the morning, the engine runs very roughly and the Service Engine Soon lamp is illuminated. * During a hot start, the engine runs very roughly and the Service Engine Soon lamp is illuminated. ??While driving or idling, the engine will misfire and the Service Engine Soon lamp is illuminated. * Various misfire faults are stored in DME fault memory. CAUSE An internal failure of the high-pressure fuel injector can lead to incorrect operation.
1107132018-12-03. Service bulletin. ENGINE AND ENGINE COOLING. N63T Engine: New Test Plan to Check Engine Oil Level with ISTA/D 3.39.21. INFORMATION With the release of ISTA/D 3.39.21, a new test plan is available for checking the engine oil level in some vehicles with the N63T engine. The test plan will help identify the actual oil level, and advise the amount that will need to be added to correctly fill the engine when topping up. When performing the scheduled oil service and filling the engine with the amount specified, the applicable ISTA/D repair instruction does not require performing this test plan. Applicable models: * F01 and F02 with the N63T engine, produced from 3/2013 and later with I-Level F001-13-03-501 or higher * F06, F07, F12 and F13 with the N63T engine, produced from 3/2013 and later with I-Level F001-13-03-501 or higher * F10 with the N63T engine produced from 7/2013 and later with I-Level F010-13-07-501 or higher Test plan path: Service Function/Drive/Motor Electronics/Motor Oil/Oil Level IMPORTANT: Do not perform this test plan on the following vehicles: * E70, E71, F01, F02, F04, F06, F07, F12 and F13 vehicles with the N63 or N63T engine, produced before 3/2013 l * F10 vehicles with the N63 engine produced before 7/2013 If this test plan is performed on these vehicles, the result is an incorrect measurement and level indication; overfilling of the engine will occur. Overfilling of the engine will result in engine damage. When a solution for vehicles which are not at one of the integration levels above is available, it will be communicated promptly. WARRANTY INFORMATION Not applicable. [ Copyright (c)2013 BMW of North America, Inc. ] https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/15702.1.B11071... 11/12/2013
5412082018-12-03. Service bulletin. VISIBILITY. Water Leak from the Front of the Sunroof. During extended periods of heavy rain, water may enter the vehicle from the area around the front of the sunroof cassette, the Roof Control Panel (FZD), the map lights, or the A-pillars. The customer may also simply state that the carpet in the front of the vehicle is wet. The sunroof cassette is overflowing due to the fact that one or both of the front sunroof drains are trapped or twisted.
5136082018-12-03. Service bulletin. VISIBILITY. "Outside Door Mirror Moves when Locking or Unlocking the Vehicle. The door mirror tilts immediately after unlocking or locking. The mirror position does not correspond to the memory position preset by the customer. Pressing the seat memory button typically will return the mirror to the stored position. Poor electrical contacts of the mirror drive in the mirror housing INFORMATION The problem has been integrated into ISTA diagnostics. Complete the diagnosis test plan using the latest ISTA version. The test plan can be accessed via the following path: ""Information Search / Function Structure / Body / Mirror / Exterior mirrors / Driver's or passenger side / Electrochromic Mirror,"" and then press ""Start Search."" Select the test plan ""AM5102_00010."""
5112132018-12-03. Service bulletin. VISIBILITY:DEFROSTER/DEFOGGER/HVAC SYSTEM:FAN/MOTOR. Grating Noise from Side Window Defroster Vent. The customer may notice a grating or creaking noise coming from the instrument panel at the extreme left or right side. It is only heard when the vehicle is in motion. CAUSE The side window defroster vent fitment (in the instrument panel) causes a grating noise when driving, and torsional forces are applied. The driver's or passenger's side can both be affected.
3101122018-12-03. Service bulletin. SUSPENSION. Clicking Noise from Front Axle. Clicking noises are heard from the front axle area while maneuvering at low speeds (e.g., parking lot maneuvers). CAUSE Movement between the contact surfaces of the wheel bearing and swivel bearing (knuckle)
1214122018-12-03. Service bulletin. ENGINE AND ENGINE COOLING. N51, N52K, N52T and N55 Engine: Various Faults Stored in DME Related to VANOS and Camshaft Position. A rattling noise can be heard from the engine compartment; the engine exhibits a loss of power; and the Service Engine Soon lamp is illuminated. One, or more of the following faults may be stored. E70, E71, E82, E88, E90, E92 and E93: 2A7C - VANOS, inlet, cold start 2A82 - VANOS, intake, variable cam control test 2A7A - VANOS, exhaust, cold start 2A87 - VANOS, intake: control fault, camshaft sticking 2D5A - VANOS, intake: control fault, camshaft sticking 2D5B - VANOS, intake: control fault, position not reached 2D54 - VANOS, exhaust, cold start: not controllable 2D55 - VANOS, intake, cold start: not controllable 2D60 - VANOS, exhaust: control fault, camshaft sticking 2D61 - VANOS, exhaust: control fault, position not reached 2D9F - Camshaft input sensor: signal implausible 2DA1 - Camshaft exhaust sensor: signal implausible 300C - Camshaft input sensor: signal high 300D - Camshaft input sensor: signal low 300E - Camshaft exhaust sensor: signal high 300F - Camshaft exhaust sensor: signal low F07, F10, F12, F13 and F25: 130104 - VANOS, intake: control fault, camshaft sticking 130108 - VANOS, intake: control fault, position not reached 130304 - VANOS, exhaust: control fault, camshaft sticking 130308 - VANOS, exhaust: control fault, position not reached 130E11 - Camshaft input sensor: signal implausible 130F11 - Camshaft exhaust sensor: signal implausible 164020 - Camshaft input sensor: signal high 164021 - Camshaft input sensor: signal low 164030 - Camshaft exhaust sensor: signal high 164031 - Camshaft exhaust sensor: signal low CAUSE One, or both (intake and/or exhaust) of the VANOS gear assemblies have failed; the attaching bolts may have also loosened and/or broken.
5136082018-12-03. Service bulletin. STRUCTURE; VISIBILITY; ELECTRICAL SYSTEM. "Outside Door Mirror Moves when Locking or Unlocking the Vehicle. The door mirror tilts immediately after unlocking or locking. The mirror position does not correspond to the memory position preset by the customer. Pressing the seat memory button typically will return the mirror to the stored position. Poor electrical contacts of the mirror drive in the mirror housing INFORMATION The problem has been integrated into ISTA diagnostics. Complete the diagnosis test plan using the latest ISTA version. The test plan can be accessed via the following path: ""Information Search / Function Structure / Body / Mirror / Exterior mirrors / Driver's or passenger side / Exterior Mirror https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/15...12/6/2013 Page 2 of 2 Malfunction,"" and then press ""Start Search."" Select the test plan ""AM5102_00010."""
6510092018-12-03. Service bulletin. EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM); EQUIPMENT. The vehicle position is missing or incorrect on the navigation map. The navigation system integrated in the Car Information Computer (CIC) is not calibrated correctly.
6310092018-12-03. Service bulletin. ELECTRICAL SYSTEM; EXTERIOR LIGHTING:BRAKE LIGHTS. INFORMATION Note: Failures that result from the installation of non-approved accessories and/or non-original parts are not covered. Procedure A with Reprogramming and Encoding the Vehicle Covered under the terms of the BMW New Vehicle/SAV Limited Warranty or the BMW Certified Pre-Owned Program. Labor operation code 00 00 006 is a Main labor operation. If you are using a Main labor code for another repair, use the Plus code labor operation 00 00 556 instead. If a control module fails to program correctly or initializations are required, the additional work must be claimed with separate labor operations under the applicable defect code listed above; refer to KSD2. And, if necessary, also: Procedure A without Reprogramming and Encoding the Vehicle (Vehicle is already at the Correct I-Level) Covered under the terms of the BMW New Vehicle/SAV Limited Warranty.
6108132018-12-03. Service bulletin. VISIBILITY. Front or Rear Windshield Wipers Fail to Operate. INFORMATION The following troubleshooting hints are based on known areas that can cause the situations described above to occur. 1. Front windshield wiper failure: perform the following checks only when the front windshield wiper fails to operate. If the rear wipers fail to operate, proceed to section 2. * Check Fuse F44 (30 A) and replace as necessary. * Check connector X333 at the front wiper motor to makes sure it is plugged in correctly, and no corrosion exists at the connection. Repair as needed.
6105132018-12-03. Service bulletin. ELECTRICAL SYSTEM. The vehicle does not start. CAUSE Software error in the CAS (Car Access System).
6105122018-12-03. Service bulletin. ELECTRICAL SYSTEM. Battery Discharged Because of Unfavorable Driving Profile. In certain situations, the battery may become discharged when the vehicle is driven frequently on short trips (less than 3 miles per trip), or when the telephone or entertainment system is used for up to 30 minutes while the vehicle is stationary. CAUSE The vehicle charging system, in extreme conditions, is not able to properly compensate for the excessive discharging of the battery caused by an unfavorable driving profile.
3202102018-12-03. Service bulletin. SUSPENSION; STEERING. "Squeaking Noises from Steering Wheel While Turning. There is a squeaking noise from the steering column when the steering wheel is turned. The rubber boot on the steering column is not positioned correctly or lacks sufficient grease for the plastic bearing. INFORMATION The problem has been integrated into ISTA diagnostics. Follow the diagnosis test plan, using the latest ISTA version. In ""Information Search,"" select the ""Function Structure"" tab. Select ""Chassis and Suspension / Steering / Steering interference noise,"" and then press ""Start Search."" Select test plan ""AM3201_00222 - Steering noises."" The BMW Group has integrated NED (Non-electric Diagnosis) into diagnosis for the purpose of finding the cause of mechanical, acoustic and visual problems. Refer to bulletin B07 03 10 for more details."
2401132018-12-03. Service bulletin. POWER TRAIN. Oil Leak from Transfer Case. Oil is leaking from the transmission area, or oil seepage is noticed from the transmission/transfer case area during a service. CAUSE The leak can be misdiagnosed as a transmission fluid leak from either the mechatronics sleeve or transmission oil pan. The leak is actually coming from the transfer case (input or output shaft seal).
1307122018-12-03. Service bulletin. ENGINE; FUEL SYSTEM, GASOLINE. N63 and S63 Engine: High-pressure Fuel Injector Replacement Procedures. The customer complains that one of the following scenarios has been encountered while operating the vehicle: * During a cold start in the morning, the engine runs very roughly and the Service Engine Soon lamp is illuminated. * During a hot start, the engine runs very roughly and the Service Engine Soon lamp is illuminated. ??While driving or idling, the engine will misfire and the Service Engine Soon lamp is illuminated. * Various misfire faults are stored in DME fault memory. CAUSE An internal failure of the high-pressure fuel injector can lead to incorrect operation.
1304092018-12-03. Service bulletin. FUEL SYSTEM, GASOLINE; ENGINE. The customer may complain that during the cold start in the morning, the engine runs very roughly and the Service Engine Soon lamp is illuminated. Various misfire fault codes (e.g., 29CC, 29D2, 29D1, 29D0, 29C0, 29CF) may be stored in the DME control module. The engine rough running complaint can be reproduced on a cold start in the workshop. During the course of diagnosis, the spark plugs, removed from the misfiring cylinders after the problem was reproduced, are found to be soaked (?wet?) with fuel, while the injector tips are covered with a layer of carbon deposit.
1302132018-12-03. Service bulletin. FUEL/PROPULSION SYSTEM. N54 Engine: Fuel Pressure Control Test Plan Error. INFORMATION Not applicable.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.