WenmarOpen by Wenmar Pro

Service bulletins for the 2019 BMW X5

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

482 on file from NHTSA, as of 2026-10-19.

By type

By component

Only bulletins with component: Engine are shown. Show all

Bulletins, newest first
B1105212022-02-22. Service bulletin. ENGINE AND ENGINE COOLING; FUEL SYSTEM, GASOLINE. The belt pulley on the mechanical coolant pump may fracture allowing the engine drive belt to come off the coolant pump and alternator.
B6624192022-01-24. Service bulletin. ELECTRICAL SYSTEM; ENGINE; STEERING. Vehicle cannot be opened or closed using comfort access, engine start is not possible, and the vehicle may not start when placing the key against the steering column.
B6114212021-12-20. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:OIL/LUBRICATION:PRESSURE/TEMPERATURE SENSOR. The BMW Gesture Control function may fail permanently as a result of high temperature fluctuations.
SIB 62 03 212021-10-25. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; ENGINE AND ENGINE COOLING. When the vehicle is operated in Sport Mode, the engine speed is no longer displayed in the BMW Head-Up Display (HUD).
B6104212021-08-09. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; EQUIPMENT; ENGINE. The customer may complain of a check control message stating "Safe share detected" (CCM-ID 953). Check control message can be verified by checking key reader information or performing the Check control message history service function.
B1101202021-08-09. Service bulletin. EQUIPMENT; ENGINE AND ENGINE COOLING:ENGINE:OIL/LUBRICATION:FILTER/SCREEN. On rare occasions during an engine oil service, the BMW Original (Genuine) engine oil filter insert is either difficult to remove or breaks apart in the oil filter housing.
B1103212021-07-19. Service bulletin. EQUIPMENT; EQUIPMENT ADAPTIVE/MOBILITY; ENGINE. B58 ENGINE: ENGINE OIL FILTER REMOVAL PROCEDURE AND TOOLS . A. For the B58 engines, a BMW Oil Catch special tool for use in conjunction with removing the engine oilfilter insert is now available.
B1213202021-02-22. Service bulletin. ELECTRICAL SYSTEM:IGNITION:COIL; ELECTRICAL SYSTEM; ENGINE. REPLACE ALL THE IGNITION COILS: The ignition coils may not have been produced to specifications which could lead to irregular running of the engine.
B6624192021-02-01. Service bulletin. ENGINE; EQUIPMENT; EQUIPMENT ADAPTIVE/MOBILITY; ELECTRICAL SYSTEM. REMOTE CONTROL IS NOT DETECTED: Vehicle cannot be opened or closed using comfort access, engine start is not possible, and the vehicle may not start when placing the key against the steering column.
B5112192020-09-14. Service bulletin. ENGINE AND ENGINE COOLING. KIDNEY GRILL ACTIVE AIR FLAP FAULTS: A check control message or MIL (Malfunction Indicator Lamp) may be illuminated, with one or more of the following faults stored: 138207- Active cooling damper control (AKKS), top: blockage at warm ambient temperature 21B043- Active cooling damper control (AKKS), top: blockage at all ambient temperatures 138222- Active cooling damper control (AKKS), above: positional deviation error detected at warm ambient temperature 138209- Active cooling damper control (AKKS), top: Control deviation at all ambient temperatures 13822B- Active cooling damper control (AKKS), top: Control deviation at all ambient temperatures 21B042- Active cooling damper control (AKKS), below: blockage at all ambient temperatures 138206- Active cooling damper control (AKKS), bottom, blockage at warm ambient temperature 138225-Active air-flap control, bottom: top limit position not detected 138224-Active air-flap control, bottom: bottom limit position not detected Multiple potential issues may be the cause, including: 1. Faulty active air flap(s) (Upper and/or lower) 2. Software error in the DME 3. Debris or blockages from outside influence (non-warranty) 4. Information error memory that does not require a repair 5. For G20 only- Detached lower active air flaps
B1802202020-08-31. Service bulletin. ENGINE; EQUIPMENT; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR. DELIVERY STOP - INSPECT NUTS ON CATALYTIC CONVERTER: BMW AG has issued a Delivery Stop (effective June 23, 2020) on certain Model Year 2020 BMW vehicles that were produced between March 10, 2020 and June 1, 2020. Do not deliver to a customer, a New, Certified Pre-Owned or Used vehicle subject to a Delivery Stop, until the vehicle is repaired. Do not use or sell replacement equipment/parts subject to a Delivery Stop. The nuts holding the catalytic converter to a bracket in the engine compartment may become loose. Over time, this may lead to damage to the exhaust system. The nuts on the catalytic converter bracket in the engine compartment have been incorrectly torqued (19 Nm instead of 28 Nm).
B1706172020-08-31. Service bulletin. ENGINE; ENGINE AND ENGINE COOLING. COOLANT LEAK FROM LOW TEMPERATURE COOLING CIRCUIT (N63R): Coolant leaking from the engine compartment. Traces of coolant leaking from the expansion tank of the low temperature cooling system. Aluminum corrosion in the charge air intercoolers, or in the radiator for the low temperature cooling is causing an unfavorable chemical reaction to the coolant.
B1703202020-06-15. Service bulletin. FUEL SYSTEM, GASOLINE; ELECTRICAL SYSTEM; LANE DEPARTURE; SERVICE BRAKES, HYDRAULIC; ENGINE AND ENGINE COOLING. COOLANT LINE QUICK DISCONNECTS LEAK IN LOW TEMPERATURES AT OR BELOW -15Ë?C (5Ë?F): The coolant reservoir in the high or low temperature cooling system is low There may be a coolant leak under the vehicle There may be a check control message (ID166) to top up coolant The low temperature cooling system have a low level warning indicator. One or more faults may be stored related to the low temp cooling system: DME - 20A201 - charge air cooling system: Coolant pump protective function due to dry running active DME - 20A209 - charge air cooling system: Coolant pump protective function due to dry running active IHKA - 80120A - Compressor: Switch off due to excess pressure in the refrigerant circuit The outside temperature at the time of the complaint is at or below -15Ë? C (5Ë? F) The O-rings that seal the quick disconnect coolant lines will not seal properly when outside temperatures are at or below -15Ë? C (5Ë? F).
B1701202020-06-15. Service bulletin. ENGINE AND ENGINE COOLING. SERVICE ACTION - ADD SILICONE BOOSTER TO LOW TEMP COOLING SYSTEM: The coolant in the low temperature cooling system may not have sufficient coolant corrosion protection.
B1304202020-06-15. Service bulletin. ENGINE AND ENGINE COOLING. TANK VENTILATION AND MIXTURE CONTROL FAULTS STORED IN THE DME: The Engine Malfunction Warning is illuminated and one or more of the following faults are stored in the DME. All models: FC 191C02 - Fuel tank ventilation system 2nd discharge point: malfunction FC 195014 - Differential pressure sensor tank vent valve signal: fixed FC 118001 - Mixture control: mixture too lean FC 118401 - Mixture control: mixture too lean large deviation I01 only: FC 124103 - Mixture control: mixture too lean FC 124101 - Mixture control: Mixture lean large deviation CAUSE Internal mechanical defect in the tank ventilation valve. The defect can also result in a very loud clicking noise when the valve is cycling.
B1101202020-06-15. Service bulletin. ENGINE. B58C AND B58M ENGINES ENGINE OIL FILTER INSERT IS DIFFICULT TO REMOVE - REMOVAL: On rare occasions during an engine oil service the BMW Original (Genuine) engine oil filter insert is either difficult to remove or breaks apart in the oil filter housing. The engine oil filter is broken. The paper is torn and the lower plastic section is stuck in the engine oil filter housing.
B1303202020-05-18. Service bulletin. ENGINE. DELIVERY STOP - REPLACE HIGH-PRESSURE PUMP: Due to an assembly error the flange bolts for the high-pressure pump did not have the proper tightening torque applied.
B6303202020-04-20. Service bulletin. ENGINE AND ENGINE COOLING; AIR BAGS. Headlight Malfunction Check Control Message: Intermittently a check control message may be present stating "Adaptive headlight failure" (CC message 127) or "Headlight range control failure" (CC message 100). In conjunction one of the following faults codes MUST be stored for this bulletin to apply: 805A0D control unit: Headlight range control stepper motor driver failure (left frontal light module) 805A0E control unit: Adaptive Headlights stepper motor driver failure (left frontal light module) 805B8D control unit: Headlight range control stepper motor driver failure (left frontal light module) 805A0E control unit: Adaptive Headlights stepper motor driver failure (right frontal light module) This only affects vehicles with a current I-level below S18A-20-03-524. Software error in the FLM02 (Frontal light electronics module-Right or left).
B1706172020-04-20. Service bulletin. FUEL SYSTEM, GASOLINE; ENGINE AND ENGINE COOLING. COOLANT LEAK FROM LOW TEMPERATURE COOLING CIRCUIT (N63R): This Service Information Bulletin (Revision 5) replaces SI B17 06 17 dated June 2019. Traces of coolant leaking from the expansion tank of the low temperature cooling system. Coolant in the low temperature cooling circuit may also have an acrid smell and discoloration (1). Aluminum corrosion in the charge air intercoolers or in the radiator for the low temperature cooling is causing an unfavorable chemical reaction to the coolant.
B1702202020-04-20. Service bulletin. ENGINE AND ENGINE COOLING. COOLANT LEAKING FROM THE LOW TEMPERATURE COOLING SYSTEM (B58C ENGINE): This Service Information Bulletin (Revision 1) replaces SI B17 02 20 dated March 2020. Premature breakdown of the coolant with gassing in the low temperature cooling system.
B1701202020-03-16. Service bulletin. ENGINE AND ENGINE COOLING. SERVICE ACTION: ADD SILICONE BOOSTER TO LOW TEMP COOLING SYSTEM: The coolant in the low temperature cooling system may not have sufficient coolant corrosion protection.
B1119182020-03-16. Service bulletin. ENGINE AND ENGINE COOLING. DELIVERY STOP: N63R AND N63M ENGINE - CHECK HIGH TEMPERATURE COOLANT SYSTEM FOR CONTAMINATION. The engine oil to coolant heat exchanger may have an internal leak resulting in engine oil contamination of the high temperature cooling system.
B1101202020-03-16. Service bulletin. ENGINE AND ENGINE COOLING. ENGINE OIL FILTER INSERT IS DIFFICULT TO REMOVE - REMOVAL: This Service Information Bulletin (Revision 1) replaces SI B11 01 20 dated February 2020. On rare occasions during an engine oil service the BMW Original (Genuine) engine oil filter insert is either difficult to remove or breaks apart in the oil filter housing. The engine oil filter is broken. The paper is torn and the lower plastic section is stuck in the engine oil filter housing (1).
B1701202020-02-18. Service bulletin. ENGINE AND ENGINE COOLING. SERVICE ACTION: ADD SILICONE BOOSTER TO LOW TEMP COOLING SYSTEM: The coolant in the low temperature cooling system may not have sufficient coolant corrosion protection. AFFECTED VEHICLES Vehicles which require this Service Action to be completed will show it as "Open" when checked either in AIR the "Service Menu" of DCSnet (Dealer Communication System) or with ISPA NEXT.
B1204192020-02-18. Service bulletin. ENGINE AND ENGINE COOLING. DME FAULT MEMORY ENTRY FOR THE CRANKSHAFT SENSOR: This Service Information Bulletin (Revision 1) replaces SI B12 04 19 dated February 2019. Technicians may notice this fault logged during a diagnostic session: Fault code: Control module: Fault Text: 160021 DME Crankshaft sensor: general loss of synchronism Environmental conditions are vehicle speed 0 (stationary) and engine speed less than 1500 rpm. There is no customer-facing symptom nor related check control message displayed. Phantom/pseudo fault due to unsuitable DME software. Background: After parking the vehicle and turning off the engine both DME control units go into sleep mode at different times. The DME of cylinder bank 2 ("secondary") goes into sleep mode first The DME of cylinder bank 1 ("primary") is still awake and can experience a reduction in signal voltage for the crankshaft sensor signal This signal change can mistakenly be evaluated as a skipped crankshaft sensor cog by the DME. If the engine is started while the primary DME is still awake this causes a brief loss of synchronization with the secondary DME. Fault 160021 is logged after three (3) consecutive engine starts with this momentary loss of synchronization. Note: Starting the engine after the primary DME has also gone into sleep mode will avoid the loss of synchronization.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.