WenmarOpen by Wenmar Pro

Service bulletins for the 2015 BMW X5

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

412 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

Bulletins, newest first
B3405152018-11-13. Service bulletin. SERVICE BRAKES. Ticking Noise from the Front Axle When Cornering This Service Information bulletin supersedes SI B34 05 15 dated December 2015. The customer may complain of a ticking noise from the front axle when cornering, maneuvering, parking or pulling away from a parking space. The noise can be heard as a metallic ticking from the area of the front wheels. Movement between the inner contact surfaces of the brake disc and drive flange of the wheel bearing hub.
B6404152018-11-05. Service bulletin. SEATS; ELECTRICAL SYSTEM; EQUIPMENT:APPLIANCE:AIR CONDITIONER. "Third Row of Seats Blower is Inoperative. The blower in the third row of seats is not working and the fault code ""E70C32 - AC-LIN: Heating in third row of seats is not responding"" has been entered in the IHKA (Integrated Heating and Airconditioning, Automatic) control unit. CAUSE LIN BUS short or open circuit in wiring or connectors Blower motor, micro switch defective Control unit, A/C, for 3rd seat row defective."
B6119152018-11-05. Service bulletin. STEERING: STEERING WHEEL/HANDLE BAR; STEERING:COLUMN; STEERING. Grating or Scraping Noise When Turning Steering Wheel. There is a grating or scraping noise when the steering wheel is turned. The noise comes from the steering column switch cluster (SZL), coil spring or steering wheel. CAUSE When the steering wheel is turned, the connection between the steering wheel and the steering column switch cluster causes torsional stress, which creates a noise in the coil spring cassette.
B3702142018-11-05. Service bulletin. SERVICE BRAKES, HYDRAULIC:ANTILOCK/TRACTION CONTROL/ELECTRONIC LIMITED SLIP:WHEEL SPEED SENSOR/TONE RING. This Service Information bulletin supersedes SI 37 02 14 dated February 2015. Unfavorable tolerances for the plug-in connections of the wheel acceleration sensors may result in fault code memory entries and the VDC being deactivated. If the VDC control unit identifies an implausable value from one of the wheel acceleration sensors, the VDC will be deactivated and the driver is informed by a Check Control message. The vehicle then defaults to the conventional suspension.
B3601152018-11-05. Service bulletin. TIRES:PRESSURE MONITORING AND REGULATING SYSTEMS. Check Control Message: Tire Pressure Monitor (RDCi) Failure. A Check Control Message states Tire Pressure Monitor (RDCi) has failed CAUSE Hardware in the remote control unit (FBD3 antenna)
B3404142018-11-05. Service bulletin. SERVICE BRAKES, HYDRAULIC; SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:DISC. Diagnosis of Compound Brake System Complaints in M Vehicles This Service Information bulletin supersedes SI 34 04 14 dated December 2014. Designates changes to the bulletin. INFORMATION 1.Visible cracks are caused by high thermal stresses during rapid heating and cooling of the brake discs. Braking from high speed with cold brake components (less than 212 degrees F) increases the likelihood of cracks to form. These surface hairline cracks are usually spread over the entire brake disc friction area, and have no negative influence on the durability or braking performance. The rotors should not be replaced only for their appearance reasons.When performing routine service on the brake system (pad replacement due to wear), the brake discs should be replaced if surface cracks are found to be greater than 13 mm, or if the brake disc thickness is below the minimum thickness. Always replace brake discs in pairs (per axle). Install new brake pads when replacing discs. By doing this, the service life of the friction pad surface is increased, and an even material loss is ensured. 2. Vibrations and/or steering wheel torsional vibrations during braking are caused by applying the brakes on discs with minimal to heavy corrosion. These vibrations are most noticeable when braking from high speeds with cold brake components (less than 212 degrees F), and will diminish with normal everyday operation. Parts replacement is not required. 3.After high brake loads, running noises can be heard when applying the brakes, and may also be heard to a limited extent after the brakes are released. (See the note in the Owner's Manual). These noises are reduced during normal everyday operation, due to further erosion of the brake pad friction lining. Visible surface cracks or craterlike recesses on the brake pad surface are caused by a minor difference in the material of the pad lining, which will decrease with further operation and should not be replaced due to their appearance.
B2704152018-11-05. Service bulletin. POWER TRAIN:DRIVELINE; WHEELS. Shudder from the Driveline on Vehicles with xDrive. There is a shudder or vibration from the driveline when taking off from a stop, or when accelerating at highway speeds. CAUSE Possible multiple root causes related to the engine, wheels & tires, suspension components or internal wear on the clutch plates of the xDrive transfer case.
B1307152018-11-05. Service bulletin. STEERING; ELECTRICAL SYSTEM:STARTER ASSEMBLY. "N57T - Automatic Start/Stop (MSA) Does Not Function. The MSA feature to shut the engine off does not function at any time, although it is set to active. The MSA test plan indicates that the ""engine stop"" inhibitor is currently active due to missing steering angle information. There are no relevant faults stored and the steering angle is calibrated correctly. CAUSE A communication error between the engine (DDE) and electronic steering (EPS) control units."
B6510152018-11-05. Service bulletin. EQUIPMENT; EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM). NAV Road Map Installation Using USB Stick. INFORMATION The Navigation road map can be installed onto the head unit in the vehicle using a USB stick connected to the USB connector in the center console in the vehicle. ? 32GB USB stick is necessary ? Desired NAV road map version can be retrieved from the HDD-Update console PROCEDURE 1. Copy the desired NAV road map from the HDD-Update console onto a 32GB USB stick. Refer to Attachment. 3. When prompted, enter the 20-digit enabling code. 4. Start the NAV road map installation and follow the on-screen instructions. WARRANTY INFORMATION Not applicable. ATTACHMENTS View PDF attachment B651015_Attachment.
B6111152018-11-05. Service bulletin. SEATS; SEATS:FRONT ASSEMBLY:SEAT HEATER/COOLER; ELECTRICAL SYSTEM. Rear Seat Heater Inoperative. The front passenger and both rear seat heaters do not work. The following fault codes are stored in the BDC (Body Doman Controller): D90C18 - LIN master I: Short circuit D90C1A - LIN master I: Communication faulty CAUSE One of the rear seat heater modules has an internal fault, which interrupts LIN bus communication.
B5116152018-11-05. Service bulletin. EQUIPMENT:OTHER:LABELS. "Affected vehicles in dealer inventory must not be retailed or delivered until the label is removed. Vehicles at ports of entry will be remedied prior to dealer delivery. On affected vehicles, there is an incorrect label regarding the appropriate engine oil. Affected vehicles can be identified with a ""Vehicle Comment"" in the DCS Warranty Vehicle Inquiry or ISPA Light. Remove the engine oil label (located in the front or rear of the hood)."
B3408142018-11-05. Service bulletin. POWER TRAIN:AXLE ASSEMBLY; WHEELS:HUB; SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:DISC. Ticking Noise from Front Axle When Cornering. The customer may complain of a ticking noise from the front axle when cornering, maneuvering, parking or pulling away from a parking space. The noise can be heard as a light metallic ticking from the front outer cornering wheel. Movement between the brake disc and wheel bearing hub.
B3201152018-11-05. Service bulletin. STEERING:COLUMN; STEERING. Noise When Adjusting the Steering Column Up or Down. Creaking noise when raising or lowering the steering column position CAUSE Steering column adjustment
B1223152018-11-05. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM; ELECTRICAL SYSTEM:SOFTWARE; VEHICLE SPEED CONTROL. "Reduced Engine Power with ""Charging Pressure Too High"" Faults Stored. When accelerating under certain conditions, the engine power may be reduced and a Check Control Message (CCM) ""Drive Faulty; Drive at moderate speed"" is displayed. The following charging pressure control fault is stored in the DME: ? Fault 120208: Exhaust camshaft sensor, signal: not plausible As a result, the engine power is reduced, and the following faults may also be set: ? Fault 120408: Charging pressure control: Switch-off, pressure build-up blocked ? Fault 120908: Charging pressure control2: Switch-off, pressure build-up blocked CAUSE DME software error"
B1221142018-11-05. Service bulletin. FUEL SYSTEM, OTHER:STORAGE:FUEL GAUGE SYSTEM; ELECTRICAL SYSTEM:SOFTWARE; FUEL SYSTEM, GASOLINE. Engine Malfunction Warning Illuminated with FC 193208: Fuel Level Plausibility Stored in DME. The customer states that the engine malfunction warning lamp is illuminated, and while filling the fuel tank, the fuel gauge did not show the proper fill level. After the vehicle is driven a short distance, the fuel gauge will update to full. When diagnosed, the following fault is stored in the DME: ? FC 193208 Fuel level, plausibility: deviation between consumption and level change Please proceed to the Procedure section. Vehicles with option 610 (Head-Up Display) are not affected. Please follow the ISTA/D test plan for the applicable faults stored in the DME, including the one listed in this bulletin. CAUSE A software error in the instrument cluster causes the fuel gauge to incorrectly update while refilling. The error occurs when the vehicle is powered up after refilling.
B6509152018-11-05. Service bulletin. EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM); EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.; EQUIPMENT:ELECTRICAL; EQUIPMENT. HU-H: Headunit Resets Intermittently or Permanently. The HU-H (Headunit-High) resets intermittently or permanently. ? The display is inoperative and there is no audio output ? Automatic system start-up after a couple of seconds CAUSE Software error in the HU-H
B6403142018-11-05. Service bulletin. EQUIPMENT:APPLIANCE:AIR CONDITIONER. A/C Operation: Reduced or No Airflow After Long Drive. The customer complains of reduced air-conditioning air flow when driving for a long period, usually greater than 30 minutes. This time varies based on outside temperature and humidity. The A/C low-pressure lines and evaporator are starting to freeze up.
B6402152018-11-05. Service bulletin. EQUIPMENT:APPLIANCE:AIR CONDITIONER. A/C Makes Unusual Whistling Noise from Center Vents. An unusual whistling noise can be heard coming from the center vent area for approximately15 seconds after the A/C is switched on. CAUSE Evaporator in the A/C system
B6103142018-11-05. Service bulletin. ELECTRICAL SYSTEM. Check Control Messages Related to Battery Charge During Cold Ambient Temperatures. On cold days with an outside ambient temperature of less than 15°F, customers may notice a check control message related to the battery that is displayed on the instrument cluster and the control information display. Under these conditions, the vehicle starts. Various power management faults can occur. The check control message (ID 229) is caused by a heavily discharged battery. ? The check control message is triggered when the current state of charge (SoC) of the battery approaches the minimum SoC that is required to start the vehicle (start capability limit). ? In low outside ambient temperatures, the start capability limit of the vehicle is higher. Therefore it takes more energy from the battery to start a cold engine. ? Without the early warning of the check control message, the current state of charge would drop below the start capability limit and the vehicle would not start. ? The vehicle's intelligent power management system actively takes measures to increase the charge of the battery, such as increasing idle speed and reducing or shutting down certain electrical consumers.
B3602152018-11-05. Service bulletin. TIRES:VALVE; WHEELS. Valve Stem Replacement with Wheel Electronics. INFORMATION The valve stems are single-use only, and must be replaced every time the wheel electronics are replaced. If you loosen the nut (1), you must replace the valve stem. Failure to replace the valve stem will lead to a pressure leak. The proper repair procedure can be found in REP 3611533. Not applicable. [ Copyright (c)2015 BMW of North America, Inc. ] Page 1 of 3 Page 1 of 1 https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/232...6/4/2015 https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/232...6/4/2015 Page 1 of 3 https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/232...6/4/2015
B1221142018-11-05. Service bulletin. ELECTRICAL SYSTEM. ?SI B12 21 14May 2015 Engine Electrical SystemsTechnical Service This Service Information bulletin supersedes SI B12 21 14 dated April 2015. designates changes to this revision SUBJECT Engine Malfunction Warning Illuminated with FC 193208: Fuel Level Plausibility Stored in DME. The customer states that the engine malfunction warning lamp is illuminated, and while filling the fuel tank, the fuel gauge did not show the proper fill level. After the vehicle is driven a short distance, the fuel gauge will update to full. When diagnosed, the following fault is stored in the DME: ? FC 193208 Fuel level, plausibility: deviation between consumption and level change Please proceed to the Procedure section. Vehicles with option 610 (Head-Up Display) are not affected. Please follow the ISTA/D test plan for the applicable faults stored in the DME, including the one listed in this bulletin. CAUSE A software error in the instrument cluster causes the fuel gauge to incorrectly update while refilling. The error occurs when the vehicle is powered up after refilling.
6504142018-11-05. Service bulletin. AIR BAGS. "Airbag Warning Light: ACSM FC 930A60 or 930A1C Seat Occupancy Detection. According to the customer, the airbag warning light was on, but it may not be on when the vehicle arrives in the workshop. 1. ACSM fault code ""930A60 - Seat occupancy detection, front passenger; malfunction"" is stored. The fault may or may not currently be present. Or 2. ACSM fault code ""930A1C - Seat occupancy detection, front passenger; malfunction"" is stored. The fault may or may not currently be present. CAUSE The front passenger seat occupancy mat consists of a seat occupancy mat with a capacitive sensor system. This means a front passenger is detected by measuring the resistance of the human body. The fault is set when moisture is detected on the mat itself."
6201152018-11-05. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. SUBJECT Head-Up Display Information No Longer Visible. The Head-up Display information is no longer visible on the windshield. The Head-up Display has moved downwards to the lowest possible position and can no longer be adjusted to a higher position. Software error in the instrument cluster
6130142018-11-05. Service bulletin. ELECTRICAL SYSTEM. "SI B61 30 14February 2015 General Electrical SystemsTechnical Service This Service Information bulletin supersedes SI B61 30 14 dated January 2015. designates changes to this revision SUBJECT BMW Maintenance Program: 12-Volt Battery Replacement Measure. INFORMATION This bulletin outlines a customer satisfaction measure that has been designed exclusively for the BMW vehicles listed above. It involves the replacement of the 12-volt battery as a preventive maintenance measure. This 12-volt battery replacement measure is: ? Effective for repairs dated on or after January 1, 2015. ? Applicable to vehicles that are still covered by the BMW Maintenance Program. This program is valid for 4 years or 50,000 miles, whichever occurs first. ? The calculation is based on the current date of repair. It is ""applicable"" when the 12-volt battery was not replaced within the last 12 months. You can then perform the battery replacement as outlined below. Please check the warranty claim history for the specific vehicle in the DCSnet Warranty Vehicle Inquiry to confirm the battery was not already replaced within the previous 12 months."
6103142018-11-05. Service bulletin. ELECTRICAL SYSTEM; POWER TRAIN. Check Control Messages Related to Battery Charge During Cold Ambient Temperatures. On cold days with an outside ambient temperature of less than 15°F, customers may notice a check control message related to the battery that is displayed on the instrument cluster and the control information display. Under these conditions, the vehicle starts. Various power management faults can be stored. When the outside temperatures drop below 46°F, the charging system is switch to full charge. CAUSE ? The check control message (ID 229) is caused by a heavily discharged battery. ? The check control message is triggered when the current state of charge (SoC) of the battery approaches the minimum SoC that is required to start the vehicle (start capability limit). ? In low outside ambient temperatures, the start capability limit of the vehicle is higher. Therefore it takes more energy from the battery to start a cold engine. ? Without the early warning of the check control message, the current state of charge would drop below the start capability limit and the vehicle would not start. ? The vehicle's intelligent power management system actively takes measures to increase the charge of the battery, such as increasing idle speed and reducing or shutting down certain electrical consumers.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.