WenmarOpen by Wenmar Pro

Service bulletins for the 2019 BMW X3

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

330 on file from NHTSA, as of 2026-10-19.

By type

By component

Bulletins, newest first
B1216192020-05-18. Service bulletin. ENGINE AND ENGINE COOLING. ERRONEOUS ELECTRIC FAN FUNCTION FAULT STORED IN THE DME: The following faults may be erroneously stored in the Digital Motor Electronics (DME): Fault code: Control module: Fault code text: 1A2806 DME Electric fan function: limited operation 1A4007 DME Electric fan function: Operating mode implausible And: There is no customer-facing vehicle symptom(s) or related check control message displayed. A software error may cause these faults to be erroneously stored in the Digital Motor Electronics (DME).
B8402142020-04-27. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT ADAPTIVE/MOBILITY. CONNECTEDDRIVE/BMW ASSIST SYSTEM DIAGNOSIS INFORMATION: This Service Information Bulletin (Revision 7) replaces SI B84 02 14 dated May 2019. ConnectedDrive/BMW Assist features are partially or completely inoperative. This Service Information Bulletin: Is being published because vehicles are down for an extended period of time when researching system failures with ConnectedDrive or BMW Assist. Will assist you both in identifying the issue and providing technical support. CAUSE Not enough information is available for BMW NA engineers to assist the technician in diagnosing the root cause.
B7204172020-04-27. Service bulletin. SEAT BELTS:FRONT:BUCKLE ASSEMBLY; ELECTRICAL SYSTEM. FALSE WARNINGS THAT THE FRONT PASSENGER SEAT IS OCCUPIED WITHOUT THE SEAT BELT BUCKLED: This Service Information Bulletin (Revision 10) replaces SI B72 04 17 dated September 2019. Acoustic and visual warnings indicate that the front passenger seat is occupied and the safety belt is not fastened when the seat is actually unoccupied. If the situation is currently present sit in the seat and move the seat to a slightly different position. The POL (Passenger Occupancy Light) light should now function correctly. In some cases the Air bag Warning Light was illuminated.
B6619192020-04-27. Service bulletin. EQUIPMENT:ELECTRICAL; LATCHES/LOCKS/LINKAGES. COMFORT ACCESS AND COMFORT GO NOT POSSIBLE: This Service Information Bulletin (Revision 1) replaces SI B66 19 19 dated May 2019. Vehicle cannot be unlocked/locked or started via Comfort Access. Remote control functionality is restored by pressing any of the key buttons or by removing and reinstalling the remote control key battery. The Display Key Digital Key and the Digital Key Card are not affected. Electrostatic discharge puts the remote control key into a deep sleep. Various situations can lead to an electrostatic charge which is often not recognized by the customer. For example walking over carpet wearing shoes that have a hard rubber sole positive and negative charges are exchanged. The sole accumulates a negative charge and an electrostatic charge develops before touching the remote control key.
B6608172020-04-27. Service bulletin. EQUIPMENT; BACK OVER PREVENTION. REAR VIEW CAMERA FAILS TO DISPLAY IMAGE: This Service Information Bulletin (Revision 6) replaces SI B66 08 17 dated January 2020. Sporadically when the rear view camera is activated no image appears in the display. The rear view camera can be activated by either: 1. Selecting reverse with the shift selector 2. Camera activation via the button on the center console Camera function returns after a terminal change.
B6522142020-04-20. Service bulletin. EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM). AUTOMATED ACTIVATION OF NAVIGATION SYSTEM DURING PDI/QC1: This Service Information Bulletin (Revision 2) replaces SI B65 22 14 dated October 2015. The INITIAL NAV enabling code no longer needs to be pre-ordered through the Parts department! When the vehicle is connected to the diagnostic system ISTA to perform PDI/QC1 the step to activate the navigation system (part of Delete Transport Mode) will automatically request the INITIAL NAV enabling code (VIN-specific) without pre-ordering the enabling code. This enabling code will be automatically delivered through ISTA and it then activates the navigation system.
B6508202020-04-20. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; ELECTRICAL SYSTEM; EQUIPMENT. DISPLAYS SPORADICALLY REACT VERY SLOWLY WHEN SCROLLING IN THE AUDIO MENU: Sporadically the reaction time of the display in the instrument cluster the head-up display or in the CID (Central Information Display) is very long. This can occur when browsing/scrolling through lists in the audio menu switching radio stations or albums. Software in the Head Unit High (HU-H3).
B6304182020-04-20. Service bulletin. AIR BAGS; EXTERIOR LIGHTING; ELECTRICAL SYSTEM. DAYTIME RUNNING LIGHT IS DIM OR DISCOLORED: This Service Information Bulletin (Revision 2) replaces SI B63 04 18 dated January 2019. One or more of the LED daytime running lights are dim or discolored. The connection between the LED module and light tube inside the headlight is damaged.
B6207192020-04-20. Service bulletin. ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL. DIGITAL SPEEDOMETER MISSING FROM THE INSTRUMENT CLUSTER AFTER PROGRAMMING DIGITAL SPEEDOMETER MISSING FROM THE INSTRUMENT CLUSTER AFTER PROGRAMMING: This Service Information Bulletin (Revision 2) replaces SI B62 07 19 dated June 2019. The digital speed display in the Instrument Cluster (Kombi) is missing or is only displayed in Kilometers per hour after ISTA programming. There are no iDrive settings for a customer to turn this on/off. Before software update. After software update and coding conversion. Software in the Instrument Cluster basic (Kombi).
B6105202020-04-20. Service bulletin. ENGINE. CCM DISPLAYED "INCREASED BATTERY DRAIN" CAUSED BY CONTROLLER: This Service Information Bulletin (Revision 1) replaces SI B61 05 20 dated February 2020. Electrostatic discharge at standstill / start engine. Energy management" The results of the Energy Diagnosis test plan identifies the Controller as the root cause of the CCM. The Controller delays the vehicle going to sleep by up to 6 minutes. In some cases this will cause the CCM 415 to be displayed when starting the vehicle. Replacing the Controller in this case will not correct this situation.
B6102202020-04-20. Service bulletin. BACK OVER PREVENTION; VISIBILITY:WINDSHIELD WIPER/WASHER. KNOCKING NOISE FROM WASHER FLUID RESERVOIR: When driving over uneven pavement or cobblestones a knocking noise is present from the passenger side front area (A pillar). Once the vehicle is driven on a flat even surface; the noise is no longer present. CAUSE Washer fluid reservoir movement caused by mounting bracket clearance.
B5130162020-04-20. Service bulletin. AIR BAGS; PARKING BRAKE. TAILGATE UNINTENTIONALLY OPENS: This Service Information Bulletin (Revision 4) replaces SI B51 30 16 dated March 2018. Trunk/tailgate may open when vehicle is locked Trunk/tailgate may open while the vehicle is in motion usually after stopping such as a traffic light etc. Vehicle key trunk/tailgate button may be accidentally pressed thus opening the tailgate.
B5109202020-04-20. Service bulletin. SUSPENSION; BACK OVER PREVENTION; VEHICLE SPEED CONTROL; VISIBILITY. G01 WIND NOISE DIAGNOSIS: Customer complaint of hissing or wind noise present in the interior of the vehicle at speeds above 60 mph. CAUSE The following areas and defects may cause this complaint: 1. A pillar gutter trim not correctly installed. 2. Door seal not correctly installed or a gap exists between the seal and the body. 3. Side view mirror cover deformity. 4. Improper door adjustment. 5. Side view mirror assembly to door alignment and triangle seal deformity.
B5107202020-04-20. Service bulletin. EQUIPMENT. UNINTENDED HATCH ACTIVATION AFTER CONVERSION: The hatch may unintentionally open.
B3405172020-04-20. Service bulletin. BACK OVER PREVENTION; SERVICE BRAKES, HYDRAULIC; WHEELS; POWER TRAIN. TICKING NOISE WHILE CORNERING WITHOUT THE BRAKES APPLIED: This Service Information Bulletin (Revision 3) replaces SI B34 05 17 dated September 2017. Ticking noise coming from front wheel while cornering without brakes applied noticeable at low speeds. The vehicle must be moving. See attached video V34 01 20 Note: For a similar noise heard when parking with the brakes applied refer to SIB 31 01 12. Microscopic movement of the contact interface between the inner brake disc and the wheel bearing flange on vehicles equipped with lightweight brake discs.
B1213182020-04-20. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL. DME FC 21A02D - COMBUSTION CONTROL: VALVE LIFT AT IDLE This Service Information Bulletin (Revision 3) replaces SI B12 13 18 dated September 2019. The vehicle will run rough or hesitate when accelerating from a stationary position.
B6105202020-03-16. Service bulletin. ELECTRICAL SYSTEM. CCM DISPLAYED "INCREASED BATTERY DRAIN" CAUSED BY CONTROLLER. A yellow CCM (Check Control Message) ID 415 is displayed- "Increased battery drain! // Battery. Electrostatic discharge at standstill / start engine. Energy management" The results of the Energy Diagnosis test plan identifies the Controller as the root cause of the CCM. The Controller delays the vehicle going to sleep by up to 6 minutes. In some cases this will cause the CCM 415 to be displayed when starting the vehicle. Replacing the Controller in this case will not correct this situation.
B1101202020-03-16. Service bulletin. ENGINE AND ENGINE COOLING. ENGINE OIL FILTER INSERT IS DIFFICULT TO REMOVE - REMOVAL: This Service Information Bulletin (Revision 1) replaces SI B11 01 20 dated February 2020. On rare occasions during an engine oil service the BMW Original (Genuine) engine oil filter insert is either difficult to remove or breaks apart in the oil filter housing. The engine oil filter is broken. The paper is torn and the lower plastic section is stuck in the engine oil filter housing (1).
B8402202020-02-18. Service bulletin. ELECTRICAL SYSTEM. REMOTE 3D VIEW NOT AVAILABLE: Remote 3D View cannot be launched In the BMW ConnectedDrive App. Software error in the Advanced Telematics Module 2 (ATM2).
B8401202020-02-18. Service bulletin. ELECTRICAL SYSTEM. BMW CONNECTEDDRIVE SERVICES ARE NOT AVAILABLE: The BMW ConnectedDrive services are not available for an extended period. This may include: Calls in the BMW Assistance app (Concierge Service) Vehicle data and status in the BMW ConnectedDrive app Remote services Remote 3D View Real Time Traffic Information (RTTI) Weather News Software error in Advanced Telematics Module 2 (ATM2).
B6621192020-02-18. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; STEERING. LDW (LANE DEPARTURE WARNING): STEERING WHEEL VIBRATION NOT STRONG This Service Information Bulletin (Revision 2) replaces SI B66 21 19 dated December 2019. Lane Departure Warning (LDW) steering wheel vibration is perceived as being not strong enough even with the strongest setting selected via the iDrive menu. Software in the vibration actuator and /or steering wheel component.
B6608172020-02-18. Service bulletin. BACK OVER PREVENTION; ELECTRICAL SYSTEM:SOFTWARE. REAR VIEW CAMERA FAILS TO DISPLAY IMAGE: This Service Information Bulletin (Revision 5) replaces SI B66 08 17 dated March 2018. Sporadically when the rear view camera is activated no image appears in the display. The rear view camera can be activated by either: 1. Selecting reverse with the shift selector 2. Camera activation via the button on the center console Camera function returns after a terminal change. Note: This error situation can rarely if ever be duplicated on demand. Head-unit interface software start-up synchronization error for the rear view camera.
B1112192020-02-18. Service bulletin. ENGINE AND ENGINE COOLING. MALFUNCTION INDICATOR LAMP IS ILLUMINATED WITH A CRANKSHAFT ADAPTION FAULT: When diagnosing an illuminated malfunction indicator lamp (MIL) and/or a different issue the following faults may also be stored in the Digital Motor Electronics (DME). Fault code Control module Fault code text 213A2B DME Increment wheel adaption faulty This situation is not associated with any drivability complaints and only affects vehicles built with a Factory I-level of 19-07-500 and later. An unfavorable DME diagnostic calibration may cause the fault code to be stored. In most circumstances this will cause the MIL to be illuminated.
B0113192020-02-18. Service bulletin. AIR BAGS. SIDE PANEL REAR LIGHT HOUSINGS: LTD WTY EXT TO 10 YEARS WITHOUT MILEAGE LIMIT: The rear light housing(s) can loosen/detach at the mounting tabs this can cause a clacking sound in the rear of the vehicle while driving. The plastic mounting tabs for the rear tail light assembly housing(s) may become too brittle and crack to the point where the hold down nut(s) can no longer keep the housing(s) in place.
B6629192020-01-21. Service bulletin. LANE DEPARTURE; BACK OVER PREVENTION. TOP VIEW CAMERA: IMAGE IS MISALIGNED. The top view image of the vehicle is misaligned when observed in the Control Information Display (CID). When the vehicle is parked in a parking spot with line markings it is clearly noticed in the CID that the lines are not parallel to the side of the vehicle. This may be noticed on either the driver side passenger side or both. The arrow identifies the line which is shown as not parallel or straight alongside the vehicle. Side view camera loose fitment in the exterior mirror bracket causing changes to the top view image.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.