Service bulletins for the 2016 BMW M4
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
229 on file from NHTSA, as of 2026-10-19.
By type
By component
Only bulletins with component: Driver assistance are shown. Show all
| B650414 | 2022-12-12. Service bulletin. LANE DEPARTURE; UNKNOWN OR OTHER; AIR BAGS; SEATS:BARRIERS; BACK OVER PREVENTION. According to the customer, the airbag warning light was on, but it may not be illuminated when the vehicle arrives in the workshop. 1. ACSM fault code "930A60 - Seat occupancy detection, front passenger; malfunction" is stored. The fault may or may not currently be present. Or 2. ACSM fault code "930A1C - Front passenger seat occupancy detection transmitting fault(moisture)" is stored. The fault may or may not currently be present. |
|---|---|
| B660115 | 2018-12-17. Service bulletin. BACK OVER PREVENTION. Surround View Camera Last User Mode Operation Change. After programming with ISTA/P 2.53.5 or a more recent version, the rear camera view is displayed when the reverse gear is selected. The vehicle does not remember the last user mode (surround/top camera view). INFORMATION An operational concept change for the surround/top camera view was introduced with ISTA/P 2.53.5 (I-level Fxx-14-07-505). When the reverse gear is selected, the default view will be the rear camera. The surround/top camera view has been removed from the last user mode function. This is to meet the upcoming (new) federal regulations regarding rear view cameras. Note: The surround/top camera view is available, but the driver must manually switch the camera view using the iDrive controller. |
| B660916 | 2018-12-10. Service bulletin. VEHICLE SPEED CONTROL:CRUISE CONTROL; EQUIPMENT; FORWARD COLLISION AVOIDANCE: ADAPTIVE CRUISE CONTROL. """Collision Warning Failed"" or ""Pedestrian Warning Failed"" CCM Display. While driving, a Check Control Message (CCM) is displayed advising of the following: Front collision warning failed Pedestrian detection failed The following fault code is stored in the KAFAS (Camera-based Driver Assistance System): 0X800AC4 - Camera calibration failed The KAFAS camera is not properly mounted and secured to the mounting bracket on the windshield; And/ or: The mounting bracket glued to the windshield is not installed correctly. The pictures below show both incorrect and correct installation. This picture shows the KAFAS camera installed in the bracket. Notice the spacing highlighted by the ""green lines""" |
| B660915 | 2018-11-13. Service bulletin. ELECTRICAL SYSTEM; LANE DEPARTURE; FORWARD COLLISION AVOIDANCE. Sporadically, a CCM (Check Control Message) is displayed advising that the Camera-based Driver Assistant system has failed. During this failure, all KAFAS (Camera-based driver assistance systems) system functionalities are inoperative. The affected functionalities are: Pedestrian Detection Front Collision Warning Lane Departure Warning Speed Limit Info (if equipped) Note: The system is functional after the interior temperature has cooled down or by cycling the ignition off and on again. |
| B660615 | 2018-11-05. Service bulletin. BACK OVER PREVENTION: AUTOMATIC SYSTEM BRAKING; BACK OVER PREVENTION: SENSING SYSTEM: CAMERA. Sporadic Check Control Messages of the Driver Assistance System. Sporadically, a CCM (Check Control Message) is displayed advising that the Camera-based Driver Assistant system has failed. This is due to the vehicle interior reaching very high temperatures. During this failure, all KAFAS (Camera-based driver assistance systems) system functionalities are inoperative. The affected functionalities are: Pedestrian Detection Front Collision Warning Lane Departure Warning Speed Limit Info (if equipped) The following fault code is stored in the KAFAS control unit: 0x800AC0 - Switching off due to excess temperature Note: The system is functional after the interior temperature has cooled down or by cycling the ignition off and on again. Incorrect calibration of the temperature sensor in the KAFAS camera. |
| B660814 | 2018-07-16. Service bulletin. BACK OVER PREVENTION. Side View Camera Does Not Display Picture. |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.