WenmarOpen by Wenmar Pro

Service bulletins for the 2015 BMW ActiveHybrid 3

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

423 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Bulletins, newest first
B1221142018-12-17. Service bulletin. ELECTRICAL SYSTEM. Engine Malfunction Warning Illuminated with FC 193208: Fuel Level Plausibility Stored in DME. The customer states that the engine malfunction warning lamp is illuminated, and while filling the fuel tank, the fuel gauge did not show the proper fill level. After the vehicle is driven a short distance, the fuel gauge will update to full. When diagnosed, the following fault is stored in the DME: ? FC 193208 Fuel level, plausibility: deviation between consumption and level change Please proceed to the Procedure section. Vehicles with option 610 (Head-Up Display) are not affected. Please follow the ISTA/D test plan for the applicable faults stored in the DME, including the one listed in this bulletin. CAUSE A software error in the instrument cluster causes the fuel gauge to incorrectly update while refilling. The error occurs when the vehicle is powered up after refilling.
B6205152018-12-10. Service bulletin. ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL; EQUIPMENT. "Instrument Cluster: CBS ""Running-in Check"" is Displayed. After replacing and / or programming the instrument cluster with ISTA/P 3.55.0 or higher (integration Level F020-15-03-501 or higher), the CBS (Condition Based Service) displays ""running-in check"" or ""1200 mile service is due"". The parameters of the CBS scopes for oil service, brake fluid, etc, can also be implausible or invalid. CAUSE Error in the CBS mapping data in the FEM (Front Electronics Module) and corrupt data in the instrument cluster during programming."
B2703152018-12-10. Service bulletin. POWER TRAIN. Vibration or Shudder from Driveline when Accelerating from a Stop. Chassis stabilization warning is displayed. Vehicle may exhibit a shudder or vibration when taking off from a stop. One or more of the following fault codes may be stored: LMV ? 440101 - Transfer box (VTG): End of transmission service life reached ? 440105 - Transfer box (VTG ) Calibration Faulty ? 440115 - Transfer box (VTG): Calibration angle deviation outside tolerance? 44011B - Set torque outside of the torque characteristic curve EGS ? 420611 - DSC interface (wheel speed): non-permitted deviation of wheel speed (actual speed of wheel RL/FL/RR/FR, 0x254) from output speed and turbine speed DSC ? 48097D - Transfer box: Fault, clutch position known, only rear-wheel drive These symptoms or faults would be stored on a vehicle with low mileage (< 12,500 miles). CAUSE A front or rear differential with the incorrect gear ratio was installed in the car. The front and rear differentials need to be geared exactly the same for the xDrive to function properly.
B1113152018-12-10. Service bulletin. ENGINE. The plastic oil filter housing may fail and lead to an internal and/or external engine oil or coolant leak.
B6212162018-12-10. Service bulletin. ENGINE AND ENGINE COOLING; ENGINE. "CCM - ""COOLANT LEVEL LOW"". Sporadically, while driving in ePower mode, a ""Coolant Low"" Check Control Message appears, even though coolant is at the specified level. FEM (Front Electronic Module) Control unit software error"
B6211162018-12-10. Service bulletin. ELECTRICAL SYSTEM. Center Information Display Switching off. INFORMATION The brightness of the CID will reduce and may switch off completely due to high temperature rise inside the vehicle. This situation is to protect the function of the CID. After lowering the temperature, the normal functions are restored. The increased temperature, protective switch-off is the reason for the fault. The fault code does not indicate a defective head unit. The normal maximum temperature operation for the head unit is between 167 and 194 F. Within these values, the CID will gradually diminish in brightness until it completely switches off. Replacing parts or programing the vehicle will not rectify the situation. The root cause is the very high temperature and is not a fault of the vehicle's systems.
B6210162018-12-10. Service bulletin. EQUIPMENT; EQUIPMENT:ELECTRICAL. HeadUp Display does not Show Full Street Names. INFORMATION Design of the HUD has limited display area. (It can only show a certain number of text characters). NOTE: Parts replacement or programming the vehicle will not recitify the situation!
B6103152018-12-10. Service bulletin. FUEL SYSTEM, GASOLINE; STEERING; STRUCTURE; EQUIPMENT; WHEELS; ELECTRICAL SYSTEM; FORWARD COLLISION AVOIDANCE; LANE DEPARTURE. Various Check Control Messages Caused by Shorted K-CAN This Service Information bulletin supersedes SI B61 03 15 dated April 2016. The customer states that one or more of the following CC messages are displayed: 627 - Steering behavior:Drive moderately 070 - Steering: Drive moderately 765 - Rear-end collision restricted 850 - Pedestrian warning restricted 236 - Driving stabilization: Drive moderately 299 - SOS call system failure 042 - Brake system: Drive moderately After performing a vehicle test, one or more of the following fault codes are stored: ACSM - C9549A Message faulty (seat memory), ACSM receiver, driver's seat module transmitter FEM - D91DE0 No message, receiver FEM, transmitter TMSL FEM - D91EE5 No message, receiver FEM, passenger seat module transmitter ACSM - C9540C Message missing, receiver ACSM, transmitter FEM TMSL - D95402 Message missing, receiver TMSL, transmitter FEM KOMBI - E11454 No message, receiver KOMBI, transmitter REM FEM - D91DE6 No message, receiver FEM, transmitter TMSL TMSR - D99401 Message missing, receiver TMSR, transmitter FEM TMSR - D99402 Message missing, receiver TMSR, transmitter FEM FEM - 8041BA AHL system faulty FEM - D916C3 No message, receiver FEM, transmitter TCB ZBE - E2D403 No message, receiver CON, transmitter FEM-ZGM TRSVC - CA9428 Message incorrect, receiver TRSVC, transmitter PDC-REM TMSL- D95401 Message missing, receiver TMSR, transmitter FEM HU-H - S0397 MOST configuration was not stored TCB - E1445F KCAN2 or KCAN4: Line fault/electrical fault FEM - 8041B6 LWR faulty REM - E58468 Body CAN2; communication fault TRSVC - CA9427 Message incorrect, receiver all around vision camera, transmitter PDC/REM FEM - D91CEC Message missing, receiver FEM, transmitter REM Shorted K-CAN wiring under driver or passenger seat Shorted K-CAN2 wires were shorted between the left side trunk trim panel and the body of the vehicle Shorted K-CAN in left rear wheel well area Shorted K-CAN under center console trim Shorted K-CAN under A-Pill
B3104162018-12-10. Service bulletin. STRUCTURE; ELECTRICAL SYSTEM:SOFTWARE. Thumping noises from the front section of the vehicle. Thumping noises from the front section of the vehicle may occur when driving over poor road surfaces. Software of the Variable Damper Control (VDC)
B2403162018-12-10. Service bulletin. POWER TRAIN:DRIVELINE:DRIVESHAFT; POWER TRAIN. TRANSMISSION OVERHEATING WARNING ON GEN2 HYBRIDS. Transmission warning light is illuminated and vehicle goes into fail-safe mode. The following Check Control messages may be displayed: CC 585 - Hybrid System Fault! CC 569 - Drivetrain, stop carefully! CC 586 - Drivetrain no restart! During diagnosis, some of the following fault codes related to transmission overheating, may be stored in the EGS control module: 44D31F1 - Temperature sensor; excessive temperature in transmission (1450 C) 44D671 - Temperature sensor system; Hotmode 1 44D672 - Temperature sensor system; Hotmode 2 with driver message 44D673 - Temperature sensor system; Hotmode 2 with torque reduction Vehicle's repair history shows a recent transmission fluid replacement under a regular maintenance program. Transmission has been overfilled during the last fluid replacement service.
B1107162018-12-10. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:MANIFOLD/HEADER/MUFFLER/TAIL PIPE; ENGINE. Diesel Engine: Intake Manifold Damaged. The Service Engine Soon light is on. There may also be: Complaints of lack of engine performance An exhaust smell coming from the engine area. The following fault codes may be stored in the DDE: 24CE00 - Hot film air mass meter: Ratio of measured to calculated air mass too high 27F000 - Charge air hose monitoring in idle: Charge air hose fallen down 290900 - Air system, air to EGR air mass flow plausibility: Measured air mass compared to calculated air mass too high 290A00 - Air system, air to EGR air mass flow plausibility: measured air mass compared to calculated air mass too high and high charging pressure control deviation 1. Excessive thermal load from the EGR system on the intake components 2. An excessive or unmetered air leak in the intake/charge air system
B8403142018-12-10. Service bulletin. EQUIPMENT:ELECTRICAL; EQUIPMENT. Bluetooth Connection Failures. There are various connectivity failures with the following devices: Apple iPhones Samsung S6 and the S6 Edge. Connectivity failure examples are: Call disconnection - Call is transferred back to the handset. In some instances the call is then transferred back to the vehicle. Contact List incomplete General connection failures Apple iOS software (issue started with iOS 8.3 continues with iOS 9.x and its variants) Samsung S6 and S6 Edge device firmware.
B6609162018-12-10. Service bulletin. VEHICLE SPEED CONTROL:CRUISE CONTROL; EQUIPMENT; FORWARD COLLISION AVOIDANCE: ADAPTIVE CRUISE CONTROL. """Collision Warning Failed"" or ""Pedestrian Warning Failed"" CCM Display. While driving, a Check Control Message (CCM) is displayed advising of the following: Front collision warning failed Pedestrian detection failed The following fault code is stored in the KAFAS (Camera-based Driver Assistance System): 0X800AC4 - Camera calibration failed The KAFAS camera is not properly mounted and secured to the mounting bracket on the windshield; And/ or: The mounting bracket glued to the windshield is not installed correctly. The pictures below show both incorrect and correct installation. This picture shows the KAFAS camera installed in the bracket. Notice the spacing highlighted by the ""green lines"""
B5112162018-12-10. Service bulletin. VISIBILITY:REARVIEW MIRRORS/DEVICES:EXTERIOR; VISIBILITY:REARVIEW MIRRORS/DEVICES; VISIBILITY. Passenger Side Mirror Dimming Feature Operational Change. INFORMATION The automatically dimming exterior mirror function on the passenger's side has been deleted from the Option Code 430 as noted above. The automatic dimming function will continue to be operational on the driver's side mirror and rear view mirror.
B2402162018-12-10. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:GEAR POSITION INDICATION (PRNDL). F30 PHEVs- Delayed Driving Readiness Status. Immediately after an engine start (start/stop button press), the gear selector is operated, but no drive position (D or R) can be engaged (transmission stays in P). The customer must operate the gear selector again to engage a desired drive position. Unfavorable software application Vehicle requires approximately 1 second after the start/stop button is pressed to establish a Drive Readiness status. If the gear selector is operated during this 1-second window, gear selection is not going to be executed and the gear shifter must be engaged again.
B2401162018-12-10. Service bulletin. POWER TRAIN; POWER TRAIN:AUTOMATIC TRANSMISSION:GEAR POSITION INDICATION (PRNDL); POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). "F15, F30 PHEVs- Gear Selector Plausibility Faults. The Check Control message ""Drive: Stop carefully"" (CCM-ID: 569) is displayed. The following fault codes may be stored in the transmission EGS control module (GKEG3HY3): 44D663 - Position plausibility: Driver's choice N/P from D/R not executed CF1701 - Gear selector switch interface, communication failure CF17A1 - Message missing: receiver EGS (A-CAN), transmitter selector switch (A-CAN) EGS software diagnostic function"
B8407152018-12-10. Service bulletin. ELECTRICAL SYSTEM. SOS Malfunction Is Displayed In Kombi Sporadically. After engine start-up, a CCM (Check Control Message) for SOS malfunction is displayed in the Kombi and in the CID (Central Information Display). One or more of the fault codes below may be stored in the TCB or Combox control unit: 0xB7F32B - GSM Antenna: Open Circuit 0xB7F31F - GSM Antenna: Short to ground 0xB7F31E - GSM Antenna: Open Circuit A signal error is identified during the aerial self-test performed by the TCB (Telematic Control Box or the Combox).
B6607162018-12-10. Service bulletin. LANE DEPARTURE. Erroneous Lane Change Warning. While driving, the Lane Change Warning (Blind Spot Detection) is illuminated erroneously on either outside mirror (orange triangle) when no other vehicles are around. CAUSE F30 - Install the correct sensor frame F34 - Program the vehicle using ISTA/P 3.58.0 or higher.
B6206162018-12-10. Service bulletin. ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL. Instrument Cluster Resets during Active Navigation. The instrument cluster (MID KOMBI) fails sporadically (all gauges falling briefly to zero, flashing of all indicator lights) and resets. Reset occurs during active route guidance and predictably when passing certain geographical positions. Software error in navigation head unit
B6123152018-12-10. Service bulletin. VISIBILITY:WINDSHIELD WIPER/WASHER. "The Low Washer Fluid Warning Light is illuminated when the Washer Fluid Tank is Full. The low washer fluid warning light is illuminated even though the washer fluid tank is full. There are no faults stored in the system for the washer fluid level switch. CAUSE A non-approved washer fluid is used (fluids that contain a silicone additive, normally colored other than blue). INFORMATION The washer fluid level sensor is a contactless capacitive sensor. The sensor sends a low fluid level signal to the gateway module (FEM - Front Electronics Module or BDC - Body Domain Controller) which in turn displays a low washer fluid warning in the instrument cluster. The use of a ""non-approved"" washer fluid (silicone-based fluid) can cause the low fluid warning light to come on even when the reservoir is full. Refer to ISTA document ""FB-GZ-B17A-F20 Washer fluid level sensor"" for information on how this capacitive sensor operates."
B6103152018-12-10. Service bulletin. STEERING. Various Check Control Messages Caused by Shorted K-CAN. The customer states that one or more of the following CC messages are displayed: 627 - Steering behavior: Drive moderately 070 - Steering: Drive moderately 765 - Rear-end collision restricted 850 - Pedestrian warning restricted 236 - Driving stabilization: Drive moderately 299 - SOS call system failure 042 - Brake system: Drive moderately After performing a vehicle test, one or more of the following fault codes are stored: ACSM - C9549A Message faulty (seat memory), ACSM receiver, driver's seat module transmitter FEM - D91DE0 No message, receiver FEM, transmitter TMSL FEM - D91EE5 No message, receiver FEM, passenger seat module transmitter ACSM - C9540C Message missing, receiver ACSM, transmitter FEM TMSL - D95402 Message missing, receiver TMSL, transmitter FEM KOMBI - E11454 No message, receiver KOMBI, transmitter REM FEM - D91DE6 No message, receiver FEM, transmitter TMSL TMSR - D99401 Message missing, receiver TMSR, transmitter FEM TMSR - D99402 Message missing, receiver TMSR, transmitter FEM FEM - 8041BA AHL system faulty FEM - D916C3 No message, receiver FEM, transmitter TCB ZBE - E2D403 No message, receiver CON, transmitter FEM-ZGM TRSVC - CA9428 Message incorrect, receiver TRSVC, transmitter PDC-REM TMSL- D95401 Message missing, receiver TMSR, transmitter FEM HU-H - S0397 MOST configuration was not stored TCB - E1445F KCAN2 or KCAN4: Line fault/electrical fault FEM - 8041B6 LWR faulty REM - E58468 Body CAN2; communication fault TRSVC - CA9427 Message incorrect, receiver all around vision camera, transmitter PDC/REM FEM - D91CEC Message missing, receiver FEM, transmitter REM Shorted K-CAN wiring under driver or passenger seat Shorted K-CAN2 wires were shorted between the left side trunk trim panel and the body of the vehicle Shorted K-CAN in left rear wheel well area Shorted K-CAN under center console trim Shorted K-CAN under A-Pillar trim
B5110162018-12-10. Service bulletin. STRUCTURE; STRUCTURE:BODY:DOOR. Groaning Noise from Doors over Rough Roads. A groaning noise is heard from the doors when driving over rough road surfaces. Window guide rubbing on door opening.
B3204162018-12-10. Service bulletin. STEERING. "Steering Assistance Failed After an Engine Start. Reduction of steering assistance after starting the engine. The DSC and steering warning lamp are illuminated in the instrument cluster. Check Control messages displayed: ""Driving stabilization. Drive carefully"" ""Increased steering effort required. Drive at moderate speed"". Control unit fault code entries: EPS: None ICM_25: 0xD01C0C - message fault (actual rack force, ID: AVL_FORC_GRD) - Timeout 0xD01B26 - message fault (actual EPS position, ID: AVL_PO_EPS) - Timeout 0xD019BF - message fault (actual driver actuator steering torque, ID: AVL_STMOM_DV_ACT) - Timeout 0xD016A5 - message fault (driving dynamics 02 check control display, ID: DISP_CC_DRDY_02) - Timeout 0xD015C4 - message fault (front axle electrical steering status, ID: ST_EST) - Timeout DSC_25: 0xD354EE - signal fault (actual front axle steering angle, ID: AVL_STEA_FTAX) - invalid No damage or other noticeable effects in the power supply and FlexRay EPS (electric power steering / electromechanical power steering): Flexray Transceiver switches itself off"
B1209162018-12-10. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR. N20 - The Service Engine Soon Light is On with DME Fault 118602 Stored. The Service Engine Soon light is on (MIL) with only the following oxygen sensor fault stored. 118602 - Oxygen sensor before catalytic converter, fine mixture control: exhaust gas after catalytic converter too lean CAUSE An actual engine related problem and/or DME software diagnostic
B1116152018-12-10. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM. N20 and N26 engine: Smoke from Exhaust when Starting a Cold Engine. When starting a cold engine, blue smoke can be seen emitting from the exhaust tailpipe for approximately 10-20 seconds. No turbo charger boost faults are stored and no drivability issues can be detected. CAUSE When the vehicle is parked overnight the engine oil pressure will equalize and may leak past the turbo charger exhaust side turbine seal.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.