WenmarOpen by Wenmar Pro

Service bulletins for the 2010 BMW 750Li

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

317 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Only bulletins with component: Engine are shown. Show all

Bulletins, newest first
B1108152018-12-10. Service bulletin. ENGINE. N63 and S63 Engine: Valve Seal Replacement This Service Information bulletin and attachment supersedes SI B11 08 15 dated March 2016. Refer to the following applicable SIBs before replacing the valve seals. SI B11 07 11 - Turbocharger Failure: Oil Supply and Return Line Blockage and Proper Repairs SI B11 07 12 - N63 Engine: Oil Consumption and/or Rough Running Complaints SI B11 01 13 - N63 Engine: Engine Oil Consumption, Engine Oil Top-ups and Refill Capacity SI B11 03 13 - Engine Oil Consumption (all models) If the valve seals are leaking, one of the following will help determine if the seals should be replaced. Smoke from the tailpipe when starting or aggressively accelerating and decelerating the engine Excessive engine oil consumption Spark plugs fouled with engine oil
B1210162018-12-10. Service bulletin. ENGINE AND ENGINE COOLING. "N63T Drivetrain Malfunction Message after Driving for Several Hours. F01, F02, F07 Target integration level: F001-16-07-501 or higher ""Drivetrain Malfunction"" message displayed with reduced engine power. Erroneous misfire faults may be stored for cylinders 3 and 6. The situation is most likely to occur after driving for several hours at constant highway speeds with light throttle (low load and low engine speed). Cycling ignition off and back on again clears the ""Drivetrain Malfunction"" warning DME software (plausibility check error)"
B1108152018-12-10. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:TURBO/SUPERCHARGER; EQUIPMENT; FUEL SYSTEM, GASOLINE. This Service Information bulletin and attachment supersedes SI B11 08 15 dated November 2015. SUBJECT N63 and S63 Engine: Valve Seal Replacement. Refer to the following applicable SIBs before replacing the valve seals. SI B11 07 11 - Turbocharger Failure: Oil Supply and Return Line Blockage and Proper Repairs SI B11 07 12 - N63 Engine: Oil Consumption and/or Rough Running Complaints SI B11 01 13 - N63 Engine: Engine Oil Consumption, Engine Oil Top-ups and Refill Capacity SI B11 03 13 - Engine Oil Consumption (all models) If the valve seals are leaking, one of the following will help determine if the seals should be replaced. Smoke from the tailpipe when starting or aggressively accelerating and decelerating the engine Excessive engine oil consumption Spark plugs fouled with engine oil
B1108152018-12-10. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:MANIFOLD/HEADER/MUFFLER/TAIL PIPE; EQUIPMENT. This Service Information bulletin and attachment supersedes SI B11 08 15 dated November 2015. SUBJECT N63 and S63 Engine: Valve Seal Replacement. Refer to the following applicable SIBs before replacing the valve seals. B11 07 11 - Turbocharger Failure: Oil Supply and Return Line Blockage and Proper Repairs B11 07 12 - N63 Engine: Oil Consumption and/or Rough Running Complaints B11 01 13 - N63 Engine: Engine Oil Consumption, Engine Oil Top-ups and Refill Capacity B11 03 13 - Engine Oil Consumption (all models) If the valve seals are leaking, one of the following will help determine if the seals should be replaced. Smoke from the tailpipe when starting or aggressively accelerating and decelerating the engine Excessive engine oil consumption Spark plugs fouled with engine oil
B1116142018-12-10. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:BELTS AND ASSOCIATED PULLEYS; EQUIPMENT ADAPTIVE/MOBILITY; ENGINE. "This Service Information bulletin and attachment supersedes SI B11 16 14 dated May 2015. designates changes to this revision SUBJECT N63 Engine: Check the Timing Chain. INFORMATION This bulletin outlines the procedure for checking the engine timing chains for wear, and should be completed in conjunction with SI B11 06 14, ""N63 Customer Care Package."" The N63CCP and N63 Engine Check the Timing Chain are NOT mandatory Technical Campaigns or Recalls. They should be completed only based on parts availability, workshop capacity, and the customer's schedule. Performing the test plans identified in the procedure below will detect wear at an early stage and, if necessary, provide a repair solution. To avoid future valvetrain wear, the vehicle must be reprogrammed and a shorter oil service interval must be retrofitted via ISTA/P. Finally, drain and replace the engine's oil and filter. After completing all necessary repairs included in the N63 Customer Care Package and the Timing Chain Check, the vehicle must be test driven for up to 30 minutes to ensure that the repairs were performed to the highest standard."
B0703142018-12-10. Service bulletin. ENGINE; STEERING; ELECTRICAL SYSTEM; EQUIPMENT. This Service Information bulletin supersedes SI B07 03 14 dated October 2015. Diagnosing Stored Fault Codes to Help Avoid Repeat Repair Visits. Fault codes stored in vehicles being serviced are not being diagnosed, leading to repeat repair visits (source- Analysis of FASTA data and repeat repair visit reports). INFORMATION Where diagnosis (vehicle or short test) with ISTA has already started, it is important to diagnose the fault code(s) listed below (when they are stored in the vehicle) to find their root cause during the current workshop visit. This will help lead to a reduction in workshop repeat repair visits and higher customer satisfaction.
1107132018-12-03. Service bulletin. ENGINE AND ENGINE COOLING. N63T Engine: New Test Plan to Check Engine Oil Level with ISTA/D 3.39.21. INFORMATION With the release of ISTA/D 3.39.21, a new test plan is available for checking the engine oil level in some vehicles with the N63T engine. The test plan will help identify the actual oil level, and advise the amount that will need to be added to correctly fill the engine when topping up. When performing the scheduled oil service and filling the engine with the amount specified, the applicable ISTA/D repair instruction does not require performing this test plan. Applicable models: * F01 and F02 with the N63T engine, produced from 3/2013 and later with I-Level F001-13-03-501 or higher * F06, F07, F12 and F13 with the N63T engine, produced from 3/2013 and later with I-Level F001-13-03-501 or higher * F10 with the N63T engine produced from 7/2013 and later with I-Level F010-13-07-501 or higher Test plan path: Service Function/Drive/Motor Electronics/Motor Oil/Oil Level IMPORTANT: Do not perform this test plan on the following vehicles: * E70, E71, F01, F02, F04, F06, F07, F12 and F13 vehicles with the N63 or N63T engine, produced before 3/2013 l * F10 vehicles with the N63 engine produced before 7/2013 If this test plan is performed on these vehicles, the result is an incorrect measurement and level indication; overfilling of the engine will occur. Overfilling of the engine will result in engine damage. When a solution for vehicles which are not at one of the integration levels above is available, it will be communicated promptly. WARRANTY INFORMATION Not applicable. [ Copyright (c)2013 BMW of North America, Inc. ] https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/15702.1.B11071... 11/12/2013
1219132018-12-03. Service bulletin. ENGINE; ELECTRICAL SYSTEM. ?Service Action: Program Control Units (Oil Level Sensor). Due to a signal error from the oil level sensor, the vehicle could display an erroneous message indicating that an oil service is due after only a short distance has been traveled.
1218132018-12-03. Service bulletin. ENGINE; ELECTRICAL SYSTEM. N63: Service Engine Soon Lamp (MIL) Is On with Fault 1D2008 Stored. Under certain low-load driving conditions at low outside ambient temperatures, the following fault may be stored in the DME with the Service Engine Soon lamp (MIL) on: Fault 1D2008 - Map thermostat, mechanical: jammed open. However, the thermostat is found to be operating correctly with sufficient heat output from the climate control system, and the engine is operating at the correct temperature. Unfavorable DME software diagnostic
1217132018-12-03. Service bulletin. ENGINE; POWER TRAIN. N55: Engine Difficult to Start at Cold Ambient Temperatures. The complaint may include any of the following symptoms: * The engine stalls immediately after a cold start before driving away * The engine may run roughly or misfire after a cold start * The engine does not start cold or may take several attempts * To assist starting when cold, the accelerator may need to be depressed slightly and the idle speed raised for a few seconds so the engine does not stall This can occur most frequently at outside ambient temperatures between -15°C and + 15°C. It is possible that the Service Engine Soon (MIL) lamp is on with misfire fault(s) stored, but it is equally possible that there will be no faults stored in the DME. Unfavorable DME software Cold start or idling problems may arise due to poor fuel quality. The use of summer fuel during cold outside temperatures may also lead to such problems.
6103132018-12-03. Service bulletin. ELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING. "High Battery Discharge Warning: Battery Needs Replacement. After the vehicle is started, a Check Control message ""High Battery Discharge Warning"" is displayed in the Central Information Display (CID). Various power supply and power management faults are stored, including the following: CAS - ""930769 Deactivation of terminal 15: upper startability limit reached"" CAS - ""93076A Deactivation of terminal 15: upper startability limit reached, but deactivation preventer or legal load/consumer active"" CAS - ""93076B Deactivation of terminal 30B: upper startability limit reached"" CAS - ""93076C Deactivation of terminal 30B: upper startability limit reached, but deactivation preventer or legal load/consumer active"" JBE - ""8020E8 Reset or deactivation of terminal 30F"" DME - ""213901 Power management: reduction or deactivation of individual electrical loads/consumers"" CAUSE The battery has become heavily discharged or is faulty. The following reasons can contribute to a prematurely failing battery: * Unfavorable driving profile - excessive short trips * Excessive terminal 30B after run - normal coolant pump or electric fan operation * Extremely cold temperatures * Vehicle faults - closed circuit draw, sleep mode preventer or frequent wakeups"
1307122018-12-03. Service bulletin. ENGINE; FUEL SYSTEM, GASOLINE. N63 and S63 Engine: High-pressure Fuel Injector Replacement Procedures. The customer complains that one of the following scenarios has been encountered while operating the vehicle: * During a cold start in the morning, the engine runs very roughly and the Service Engine Soon lamp is illuminated. * During a hot start, the engine runs very roughly and the Service Engine Soon lamp is illuminated. ??While driving or idling, the engine will misfire and the Service Engine Soon lamp is illuminated. * Various misfire faults are stored in DME fault memory. CAUSE An internal failure of the high-pressure fuel injector can lead to incorrect operation.
1216112018-12-03. Service bulletin. ENGINE; POWER TRAIN. N55 Engine Failsafe - FC 120308 Boost Pressure Control, Plausibility: Pressure Too Low Stored in DME Fault Memory. INFORMATION The customer complains the SES is illuminated and the engine has reduced power (engine failsafe mode).
B1111172018-12-03. Service bulletin. ENGINE. ?ENGINE LEAK DIAGNOSIS ON TURBOCHARGED V8 ENGINES. When diagnosing an engine oil leak or a coolant leak on turbocharged V8 engines it is necessary to use a borescope to identify if the source of the leak is from under the turbochargers. Engine oil or coolant leaking from the bell housing area or the front timing chain cover area may be caused by the turbocharger itself, a turbocharger oil/coolant feed line or turbocharger oil/coolant return line. Do not remove the transmission and do not dissemble the engine before performing this inspection. If necessary, use engine oil leakage detection dye.
B1108152018-12-03. Service bulletin. ENGINE. N63 and S63 Engine: Valve Seal Replacement. Refer to the following applicable SIBs before replacing the valve seals. * B11 07 11 - Turbocharger Failure: Oil Supply and Return Line Blockage and Proper Repair * B11 07 12 - N63 Engine: Oil Consumption and/or Rough Running Complaints * B11 01 13 - N63 Engine: Engine Oil Consumption, Engine Oil Top-ups and Refill Capacity * B11 03 13 - Engine Oil Consumption (all models) If the valve seals are leaking, one of the following will help determine if the seals should be replaced. * Smoke from the tailpipe when starting or aggressively accelerating and decelerating the engine in addition to excessive engine oil consumption * Spark plugs fouled with engine oil and excessive engine oil consumption * Excessive engine oil consumption All Vehicles: On vehicles, where an excessive oil consumption between services is the only complaint, a complete oil consumption test as described in SI B11 03 13, must be performed first before replacing the valve seals. On vehicles exhibiting reproducible smoking from the tailpipe when hot, additional engine diagnostic steps (e.g. engine compression test, leak-down tests; inspection of the crankcase ventilation lines and turbo intake/outlet tubes for excessive oil accumulation) should be performed and documented prior to replacement of the valve seals, in order to eliminate other possible causes. Refer to the SIBs listed above for important diagnostic tips. Do not remove the intake manifolds to clean the intake valve carbon.
1307122018-11-26. Service bulletin. ENGINE; FUEL SYSTEM, GASOLINE. N63 and S63 Engine: High-pressure Fuel Injector Replacement Procedures. The customer complains that one of the following scenarios has been encountered while operating the vehicle: * During a cold start in the morning, the engine runs very roughly and the Service Engine Soon lamp is illuminated. * During a hot start, the engine runs very roughly and the Service Engine Soon lamp is illuminated. ??While driving or idling, the engine will misfire and the Service Engine Soon lamp is illuminated. * Various misfire faults are stored in DME fault memory. CAUSE An internal failure of the high-pressure fuel injector can lead to incorrect operation.
1304092018-11-26. Service bulletin. ENGINE; FUEL SYSTEM, GASOLINE. "N54 Engine: Diagnosis of Cold Start Rough Running with Misfire Faults. The customer may complain that during the cold start in the morning, the engine runs very roughly and the Service Engine Soon lamp is illuminated. Various misfire fault codes (e.g., 29CC, 29D2, 29D1, 29D0, 29C0, 29CF) may be stored in the DME control module. The engine rough running complaint can be reproduced on a cold start in the workshop. During the course of diagnosis, the spark plugs, removed from the misfiring cylinders after the problem was reproduced, are found to be soaked (""wet"") with fuel, while the injector tips are covered with a layer of carbon deposit. Possible cause: high-pressure injector failure (leakage or incorrect spraying pattern) due to internal wear or unfavorable stock of tolerances IMPORTANT: For comprehensive N54 drivability diagnostics, always refer to the ""N54 Engine Diagnostic Fault Tree"" file (the current version ""02_14_13"" is found as a PDF attachment to SI B12 55 06)."
1101132018-11-26. Service bulletin. ENGINE. "N63 and N63T Engine: Engine Oil Consumption, Engine Oil Top-ups and Refill Capacity. Customers with one of the vehicles above may complain that the engine's oil consumption is ""too high,"" resulting in engine oil top-ups and workshop visits to address the issue before the vehicle displays an engine oil service as being ""due."" When the vehicle's engine oil drops to the minimum level, a message will display in the vehicle advising the driver to ""add 1 quart of engine oil."" After topping up and continued operation, the ""add engine oil"" message may display again before an engine oil service is required and performed. CAUSE Engines that are fitted with a turbocharger, as part of their normal operation, will consume engine oil at a higher rate than a naturally aspirated engine (non-turbocharged engine). In this case, a ""turbocharged"" engine could require topping up of the engine oil more frequently."
B1101132018-11-26. Service bulletin. ENGINE. N63 AND N63T ENGINE: ENGINE OIL CONSUMPTION, ENGINE OIL TOP-UPS AND REFILL CAPACITY. Customers with one of the vehicles above may complain that the engine's oil consumption is "too high," resulting in engine oil top-ups and workshop visits to address the issue before the vehicle displays an engine oil service as being "due." When the vehicle's engine oil drops to the minimum level, a message will display in the vehicle advising the driver to "add 1 quart of engine oil." After topping up and continued operation, the "add engine oil" message may display again before an engine oil service is required and performed. CAUSE Engines that are fitted with a turbocharger, as part of their normal operation, will consume engine oil at a higher rate than a naturally aspirated engine (non-turbocharged engine). In this case, a "turbocharged" engine could require topping up of the engine oil more frequently.
1101132018-11-26. Service bulletin. ENGINE AND ENGINE COOLING. MService Action: Replace the Coolant Pump. Coolant is leaking from the coolant pump. CAUSE The coolant pump may develop cracks in the plastic housing. These cracks may result in a coolant leak.
1114142018-11-26. Service bulletin. ENGINE. Engine Damage Due to Debris in Oil Passages. After performing extensive engine repairs (e.g., cylinder head removal), the engine begins to knock and may lose power. Debris has entered the engine oiling passages during cleaning of the engine block and cylinder head mating surfaces during engine repair.
7102142018-11-13. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:DIESEL; EQUIPMENT:OTHER:LABELS. Service Action: Replace Emission Label. Certain 2015 model year vehicles with N47T and N57T diesel engines were produced with an "emissions" label which contains incorrect information pertaining to the 2015 model year. Affected vehicles in dealer inventory must not be retailed or delivered until this issue is corrected. Vehicles at VDCs will be repaired prior to dealer delivery.
6206132018-11-13. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; ENGINE. Condition Based Service Due Date Is Reset to 01/2000. The Condition Based Service (CBS) due date is reset to 01/2000 and cannot be updated for: * Oil Service * Check Vehicle Note: No fault code is stored Software error in the Instrument Cluster.
1307122018-11-13. Service bulletin. ENGINE; FUEL SYSTEM, GASOLINE; FUEL SYSTEM, GASOLINE:FUEL INJECTION SYSTEM:INJECTORS. N63 and S63 Engine: High-pressure Fuel Injector Replacement Procedures. The customer complains that one of the following scenarios has been encountered while operating the vehicle: * During a cold start in the morning, the engine runs very roughly and the Service Engine Soon lamp is illuminated. * During a hot start, the engine runs very roughly and the Service Engine Soon lamp is illuminated. While driving or idling, the engine will misfire and the Service Engine Soon lamp is illuminated. * Various misfire faults are stored in DME fault memory. CAUSE An internal failure of the high-pressure fuel injector can lead to incorrect operation.
1307122018-11-13. Service bulletin. ENGINE AND ENGINE COOLING. N63 and S63 Engine: High-pressure Fuel Injector Replacement Procedures. The customer complains that one of the following scenarios has been encountered while operating the vehicle: ? During a cold start in the morning, the engine runs very roughly and the Service Engine Soon lamp is illuminated. ? During a hot start, the engine runs very roughly and the Service Engine Soon lamp is illuminated.? While driving or idling, the engine will misfire and the Service Engine Soon lamp is illuminated. ? Various misfire faults are stored in DME fault memory. CAUSE An internal failure of the high-pressure fuel injector can lead to incorrect operation.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.