WenmarOpen by Wenmar Pro

Service bulletins for the 2017 BMW 550i

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

188 on file from NHTSA, as of 2026-10-19.

By type

By component

By topic

Only bulletins with component: Driver assistance are shown. Show all

Bulletins, newest first
B6504142022-12-12. Service bulletin. LANE DEPARTURE; UNKNOWN OR OTHER; AIR BAGS; SEATS:BARRIERS; BACK OVER PREVENTION. According to the customer, the airbag warning light was on, but it may not be illuminated when the vehicle arrives in the workshop. 1. ACSM fault code "930A60 - Seat occupancy detection, front passenger; malfunction" is stored. The fault may or may not currently be present. Or 2. ACSM fault code "930A1C - Front passenger seat occupancy detection transmitting fault(moisture)" is stored. The fault may or may not currently be present.
B3405172020-04-20. Service bulletin. BACK OVER PREVENTION; SERVICE BRAKES, HYDRAULIC; WHEELS; POWER TRAIN. TICKING NOISE WHILE CORNERING WITHOUT THE BRAKES APPLIED: This Service Information Bulletin (Revision 3) replaces SI B34 05 17 dated September 2017. Ticking noise coming from front wheel while cornering without brakes applied noticeable at low speeds. The vehicle must be moving. See attached video V34 01 20 Note: For a similar noise heard when parking with the brakes applied refer to SIB 31 01 12. Microscopic movement of the contact interface between the inner brake disc and the wheel bearing flange on vehicles equipped with lightweight brake discs.
B6609162018-12-10. Service bulletin. VEHICLE SPEED CONTROL:CRUISE CONTROL; EQUIPMENT; FORWARD COLLISION AVOIDANCE: ADAPTIVE CRUISE CONTROL. """Collision Warning Failed"" or ""Pedestrian Warning Failed"" CCM Display. While driving, a Check Control Message (CCM) is displayed advising of the following: Front collision warning failed Pedestrian detection failed The following fault code is stored in the KAFAS (Camera-based Driver Assistance System): 0X800AC4 - Camera calibration failed The KAFAS camera is not properly mounted and secured to the mounting bracket on the windshield; And/ or: The mounting bracket glued to the windshield is not installed correctly. The pictures below show both incorrect and correct installation. This picture shows the KAFAS camera installed in the bracket. Notice the spacing highlighted by the ""green lines"""
B6619172018-12-10. Service bulletin. LANE DEPARTURE; ELECTRICAL SYSTEM. ?SERVICE ACTION: CHECK AND REPLACE LANE CHANGE WARNING SENSOR. The Lane Change Warning sensor may have been produced with faulty components. This may lead to a failure of the Lane Change Warning system (SWW). Lane Change Warning sensor hardware defect.
B2701182018-12-03. Service bulletin. STEERING; ELECTRONIC STABILITY CONTROL (ESC). "?DYNAMIC STABILTY CONTROL WARNING ON WITH LIMITED POWER STEERING ASSIST This Service Information bulletin replaces SI B34 09 16 dated January 2017 What's New: ? This SIB is a complete revision of B34 09 16. Steering feels heavy (limited power assist) The Dynamic Stability Control (DSC) light and Service Engine Soon light may be on. The following message may be displayed in the Check Control (CC): * CCM 350 ""It is possible to continue to drive. All-wheel drive system."" * Other CC messages may be stored related to: Restraint system / lane change warning / distance information / pedestrian protection. One or both of the following faults are stored in the DSC: * D36500 - Message fault (xDrive actuator information, ID: XDRV_ACT_INFO) - Timeout * D356E4 - Message fault (status of distribution of the longitudinal torque on the front axle rear axle, ID: ST_REPAT_XTRQ_FTAX_BAX) - Timeout The following faults can also be stored in the DDE or DME: * DDE: CD95E0 - Message (ST_REPAT_XTRQ_FTAX_BAX, 19.3.4,FX), Timeout: Message (status of distribution of longitudinal torque of front axle rear axle) from longitudinal torque distribution failed * DME: CDA056 - FlexRay, message (status of distribution of longitudinal torque of front axle rear axle / xDrive actuator information, 19.3.4): missing Internal fault in the transfer case control unit (Longitudinal Torque Module - LMV). "
B6608172018-11-26. Service bulletin. BACK OVER PREVENTION; VISIBILITY:REARVIEW MIRRORS/DEVICES. REAR VIEW CAMERA FAILS TO DISPLAY IMAGE. Sporadically, when the rear view camera is activated, either via selecting reverse with the shift selector or by direct camera selection, no image appears in the display. Camera function returns after terminal change. Note: This error situation can rarely, if ever, be duplicated on demand. Head-unit interface software error for the rear view camera.
B3101122018-11-05. Service bulletin. EQUIPMENT; BACK OVER PREVENTION; SUSPENSION:FRONT:WHEEL BEARING. CLICKING NOISE FROM FRONT AXLE This Service Information bulletin supersedes SI 31 01 12 dated June 2015. Clicking noises are heard from the front axle area while maneuvering at low speeds (e.g., parking lot maneuvers). CAUSE Movement between the contact surfaces of the wheel bearing and swivel bearing (knuckle)
B6621162018-11-05. Service bulletin. ENGINE; LANE DEPARTURE: SENSING SYSTEM: OTHER; SERVICE BRAKES. KAFAS CAMERA-BASED ASSISTANCE SYSTEM LIMITS. INFORMATION The situations described above may all be caused by known limitations of the system such as: Dirty windshield Incomplete calibration process Unsuccessful calibration Restricted visibility- weather conditions or parked vehicles Missing lamps on target vehicle Non-standard vehicle exterior surfaces Insufficient ambient lighting Abrupt motion of target vehicle.
B3403172018-11-05. Service bulletin. ELECTRONIC STABILITY CONTROL:AUTOMATIC (ASC). DYNAMIC STABILITY CONTROL FAILURE. Instrument cluster indicates Dynamic Stability Control (DSC) failure. You cannot establish communication with the DSC control unit. Associated control units (DME, ACSM) register DSC-related communication time-outs. After battery reset, DSC operates normally and has no faults registered. Software in the DSC control module.
B6608142018-07-16. Service bulletin. BACK OVER PREVENTION. Side View Camera Does Not Display Picture.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.