WenmarOpen by Wenmar Pro

Service bulletins for the 2016 BMW 435i

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

325 on file from NHTSA, as of 2026-10-19.

By type

By component

Bulletins, newest first
6504142018-11-05. Service bulletin. AIR BAGS. "Airbag Warning Light: ACSM FC 930A60 or 930A1C Seat Occupancy Detection. According to the customer, the airbag warning light was on, but it may not be on when the vehicle arrives in the workshop. 1. ACSM fault code ""930A60 - Seat occupancy detection, front passenger; malfunction"" is stored. The fault may or may not currently be present. Or 2. ACSM fault code ""930A1C - Seat occupancy detection, front passenger; malfunction"" is stored. The fault may or may not currently be present. CAUSE The front passenger seat occupancy mat consists of a seat occupancy mat with a capacitive sensor system. This means a front passenger is detected by measuring the resistance of the human body. The fault is set when moisture is detected on the mat itself."
6103142018-11-05. Service bulletin. ELECTRICAL SYSTEM; POWER TRAIN. Check Control Messages Related to Battery Charge During Cold Ambient Temperatures. On cold days with an outside ambient temperature of less than 15°F, customers may notice a check control message related to the battery that is displayed on the instrument cluster and the control information display. Under these conditions, the vehicle starts. Various power management faults can be stored. When the outside temperatures drop below 46°F, the charging system is switch to full charge. CAUSE ? The check control message (ID 229) is caused by a heavily discharged battery. ? The check control message is triggered when the current state of charge (SoC) of the battery approaches the minimum SoC that is required to start the vehicle (start capability limit). ? In low outside ambient temperatures, the start capability limit of the vehicle is higher. Therefore it takes more energy from the battery to start a cold engine. ? Without the early warning of the check control message, the current state of charge would drop below the start capability limit and the vehicle would not start. ? The vehicle's intelligent power management system actively takes measures to increase the charge of the battery, such as increasing idle speed and reducing or shutting down certain electrical consumers.
1221142018-11-05. Service bulletin. ENGINE; ELECTRICAL SYSTEM. SI B12 21 14February 2015 Engine Electrical SystemsTechnical Service This Service Information bulletin supersedes SI B12 21 14 dated December 2014. designates changes to this revision SUBJECT Engine Malfunction Warning Illuminated with FC 193208: Fuel Level Plausibility Stored in DME. The customer states that the engine malfunction warning lamp is illuminated, and while filling the fuel tank, the fuel gauge did not show the proper fill level. After the vehicle is driven a short distance, the fuel gauge will update to full. When diagnosed, the following fault is stored in the DME: z FC 193208 Fuel level, plausibility: deviation between consumption and level change Please proceed to the Procedure section. Vehicles with option 610 (Head-Up Display) are not affected. Please follow the ISTA/D test plan for the applicable faults stored in the DME, including the one listed in this bulletin. CAUSE A software error in the instrument cluster causes the fuel gauge to incorrectly update while refilling. The error occurs when the vehicle is powered up after refilling.
B8406162018-11-05. Service bulletin. EQUIPMENT; EQUIPMENT ADAPTIVE/MOBILITY; EQUIPMENT:ELECTRICAL. BMW ONLINE NON-FUNCTIONAL: CHECK ICC-ID IN ACCOUNT. BMW Online/BMW ConnectedDrive not functional. Vehicle and service cockpit have different ICC-ID's.
B8405162018-11-05. Service bulletin. EQUIPMENT:ELECTRICAL; EQUIPMENT ADAPTIVE/MOBILITY. BMW ONLINE NON-FUNCTIONAL: CHECK ICC-ID IN ACCOUNT. The ConnectedDrive Services are non-functional after a hardware exchange of the telematics control unit. This is not indicated by CC-message. ConnectedDrive Services not synchronized by Telematics Control Unit.
B6618162018-11-05. Service bulletin. ELECTRICAL SYSTEM. INFORMATION ON THE OPERATION OF THE SMART OPENER. INFORMATION ON THE OPERATION OF THE SMART OPENER MODEL F07 (5 Series Gran Turismo) F10 (5 Series) F12 (6 Series Convertible) F13 (6 Series Coupe) F15 (X5) F16 (X6) F22 (2 Series Coupe) F23 ( 2 Series Convertible) F25 (X3) F26 (X4) F30 (3 Series Sedan) F31 (3 Series Wagon) F32 (4 Series Coupe) F33 (4 Series Convertible) F34 (3 Series Gran Turismo) F36 (4 Series Gran Coupe) F48 (X1) F80 (M3 Sedan) F82 (M4 Coupe) F83 (M4 Convertible) F85 (X5 M) F86 (X6 M) G12 (7 Series) I01 (i3 Series) Vehicles with option code SA-0322 (Comfort Access) without M-Sport trim INFORMATION The smart opener (Contactless tailgate) operates as described below: Ignition key must be within 3 feet behind the vehicle, clear from any interference like a smartphone The customer must be at least an arms-length behind the vehicle Kick your foot forwards & backwards under the vehicle in one quick movement The taillights flash confirming that the trunk will open The trunk then successfully opens For more information an instructional video can be viewed which demonstrates the operation. Thanks to BMW of Tenafly for providing the video. tinyurl.com/Autotrunk1 https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/358...9/3/2016 Page 2 of 2 WARRANTY INFORMATION Not applicable. [ Copyright (c)2016 BMW of North America, Inc. ] https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/358...9/3/2016
B6412162018-11-05. Service bulletin. EQUIPMENT:APPLIANCE:AIR CONDITIONER. "HVAC BLOWER NOT WORKING. HVAC blower is not working. Condensation occurs even though blower is working. CC message ""Increased battery discharge"" - standby current violation may be displayed. Climate control unit (IHKA) software"
B5133162018-11-05. Service bulletin. STRUCTURE:BODY; SEATS; EQUIPMENT ADAPTIVE/MOBILITY. SLOSHING NOISES/WATER IN REAR PASSENGER COMPARTMENT. Water sloshing noises coming from the rear passenger compartment (left or right) while driving. Water ingress in the rear passenger compartment (rear seat bench / rear passenger compartment foot well / rear passenger compartment side panel) or luggage compartment. Failure of various control units installed in the area of the water removal channel. Poor water drainage due to dirt at the seal plug in the area of the fixed side glass/trim panel. Faulty clip on the water collecting channel. Dirt blocking the water drain to the side sill.
B5130162018-11-05. Service bulletin. STRUCTURE:BODY:TAILGATE; STRUCTURE:BODY:TRUNK LID. TAILGATE UNINTENTIONALLY OPENS. Trunk/tailgate may open when vehicle is locked. Trunk/tailgate may open while the vehicle is in motion. Usually after stopping, such as a traffic light etc. Vehicle key trunk/tailgate button may accidentally be pressed, thus opening the tailgate.
B5116162018-11-05. Service bulletin. STRUCTURE:BODY. Noise from Cargo Cover. A rattling sound may be heard from the rear cargo cover. Excessive clearance on mounting tabs.
B5116152018-11-05. Service bulletin. EQUIPMENT:OTHER:LABELS; ENGINE. "Delivery Stop: Remove Engine Oil Label. Affected vehicles in dealer inventory must not be retailed or delivered until the label is removed. Vehicles at ports of entry will be remedied prior to dealer delivery. On affected vehicles, there is an incorrect label regarding the appropriate engine oil. Affected vehicles can be identified with a ""Vehicle Comment"" in the DCS Warranty Vehicle Inquiry or ISPA Light. https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/248...9/3/2016 Page 2 of 2"
B3406162018-11-05. Service bulletin. SERVICE BRAKES, AIR:ANTILOCK:WHEEL SPEED SENSOR; SERVICE BRAKES, HYDRAULIC:ANTILOCK/TRACTION CONTROL/ELECTRONIC LIMITED SLIP:WHEEL SPEED SENSOR/TONE RING. "DSC ""WHEEL SPEED SENSOR"" FAULT CODES AND MALFUNCTION INDICATOR LAMP- DIAGNOSTIC. 1. DSC's fault codes stored from two different wheel speed sensors (both front or both rear): 4809B0 - wheel speed sensor - front left - drive off recognition faulty and 4809CD - wheel speed sensor - front right - drive off recognition faultyor 4809B9 - wheel speed sensor - rear left - drive off recognition faulty and 480686 - wheel speed sensor - rear right - drive off recognition faulty. 2. Next ignition ON (after above codes stored). a) DME fault can occur:1F054D - drive, safety function: Drive power output reduced, DSC signals implausible and b) Malfunction Indicator Lamp (MIL) may light up. Faulty drive off recognition due to: a towing operation with a raised axle operation of the vehicle on the vehicle hoist operation of the vehicle on the roller test stand DSC diagnosis recognizes implausible wheel speeds, so no control is possible. DME fault is entered on safety grounds since the DSC fault still exists after a terminal change and may only be removed while driving."
B7103162018-11-05. Service bulletin. EQUIPMENT. SERVICE ACTION: B-PILLAR COMPLIANCE LABEL: CHASSIS NUMBER VERIFICATION. Vehicles may contain one or more incorrect labels. Incorrect labels attached during production.
B6513162018-11-05. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; EQUIPMENT. "NBT-EVO Head Unit Cannot Be Swapped Between Vehicles for Testing This Service Information bulletin supersedes SI B65 13 16 dated July 2016.. If an NBT-EVO head unit is swapped into a different vehicle it will enter a locked mode once it recognizes a different VIN. This will set a fault in the Head Unit (NBT-EVO), Fault Code ""B7F87A: Burgler Actively Registered / Component Protection Active"" This will require REPLACEMENT of the head unit to restore operation. To prevent easy re-use of stolen Head units additional features are introduced with 11/15 ISTA/P software to bring NBT-EVO to a higher security level. In NBT-EVO the mechanism is called ""Trusted VIN"""
B6305162018-11-05. Service bulletin. EXTERIOR LIGHTING:HEADLIGHTS:CONCEALMENT DEVICES. "HEADLIGHT ASSEMBLIES HAVE VISIBLE INTERNAL MOISTURE/CONDENSATION. Water on the inside (A) or misting (B) of both headlight lenses that is visible from outside. Water inside the headlights can be caused by two situations: Water/moisture ingress into the headlight housing. Thermal conditions that result in the formation of condensation. Note: An important indication that the moisture issue is caused by ""condensation"" rather than a ""water leak"" into the headlight housing, there will be misting/condensation in ""both headlights."""
B6524162018-11-05. Service bulletin. EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM). "NBT NAVIGATION DOES NOT ROUTE ON TOLL ROADS. NBT Navigation does not provide routes that include certain toll roads. CAUSE Roads that have toll lanes ""without a cash option"" where not utilized for routing in NBT map data versions: NEXT 2015-1 NEXT 2015-2 NEXT 2016-1 As an enhancement, the NEXT 2017-1 map release now provides information about toll lanes ""without cash option"". UPDATE Install new map data."
B6523162018-11-05. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; EQUIPMENT; EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.. ?AUDIO VOLUME NOT RESTORED AFTER MSA STOP, ENTRY HEAD UNIT. Volume of audio system (when set to near maximum) is reduced when Auto Start-Stop (MSA) stop occurs and is not restored upon automatic engine restart. This is normal system behavior - serves to protect the head unit, battery drain and avoidance of incremental leaps in the loudness. The loudness is reduced to 2/3 of maximum and is not restored. Note: Air conditioning output is also reduced upon MSA stop and is not restored for similar reasons.
B5138162018-11-05. Service bulletin. STRUCTURE. SERVICE ACTION: LEFT SIDE DOORS MAY NOT OPEN FROM OUTSIDE. Left side doors (front and/or rear) may not be able to be opened from the outside. Bowden cable may twist and come loose from the bracket on the outside door handle support.
B3405162018-11-05. Service bulletin. SERVICE BRAKES. CBS BRAKE PAD CALCULATION AND CORRECTION. When a vehicle comes into the workshop for any repair or maintenance job, the bundling calculator recommends a brake maintenance checkup. No brake warning light is illuminated. CBS shows 3,107 miles or slightly higher for the next brake service displayed via Key Reader, or vehicle's Control Display (in Vehicle Info/Status/Service required/Brake pads) CAUSE CBS calculates the remaining brake pad wear based on brake pressure, speed, vehicle specific parameters (i.e. NAO pads), brake temperature as well as cumulative brake application time. Due to variation of these parameters and outside environmental influences, this calculation can deviate from the real brake pad wear. Starting from the above-mentioned production dates of the vehicles indicated, the CBS brake pad wear calculation has been changed, and is now based only on the brake pad wear sensor. Important Note: To avoid a too-slow wear prediction, the CBS brake model will estimate the need for repairs, in some cases, rather early. Calculation will level at 3,107 miles and stay at this value until the CBS brake pad wear sensor is triggered. https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/36...11/8/2016 Page 2 of 2 After the sensor is triggered, the CBS mileage will count down indicating to the customer that the brake repairs will be due.
B8409162018-11-05. Service bulletin. EQUIPMENT. "SERVICE ACTION: SUPPLEMENTARY PAGE NEEDED IN OWNER'S MANUAL. Operator's manual of affected vehicles does not contain required information on wireless smartphone charging accessory. AFFECTED VEHICLE Vehicles which require this Service Action to be completed will show it as ""Open"" when checked either in the ""Service Menu"" of DCSnet (Dealer Communication System) or with the Key Reader."
B8404162018-11-05. Service bulletin. ELECTRICAL SYSTEM. SOS MALFUNCTION DISPLAYED. An SOS malfunction is seen in the Kombi. When pressing the E-Call/SOS button in the overhead console, nothing happens. Fault code B7F33C (internal ECU error) is stored in the Telematics control unit (ATM/TCB2). There are 2 known causes for this failure. They are as follows: Software file missing from the ATM/TCB2 control module Water leak at shark-fin leading to corrosion in the ATM/TCB2 control module
B6412162018-11-05. Service bulletin. EQUIPMENT. "HVAC BLOWER NOT WORKING This Service Information bulletin supersedes SI B64 12 16 dated August 2016. HVAC blower is not working. Condensation occurs even though blower is working. CC message ""Increased battery discharge"" - standby current violation may be displayed. Climate control unit (IHKA) software"
B5136162018-11-05. Service bulletin. WHEELS. REWORKING THE PVC SEAM SEAL ON THE RIGHT REAR WHEEL ARCH. PVC Seam Sealer on the right rear inner wheel arch may not have been properly applied. Ineffective manufacturing procedure.
B5135162018-11-05. Service bulletin. STRUCTURE. PAINT ON THE B-PILLAR IS SCRATCHED/DAMAGED. Paint on B-pillar is scratched. Especially noticeable on dark colored paint. Door seal is rubbing against entry opening surfaces.
B5132162018-11-05. Service bulletin. STRUCTURE:BODY:DOOR. CREAKING NOISES FROM DOOR TRIM PANEL. Creaking noise is heard from door trim panel while driving on rough roads. Door trim panel is contacting the inner door panel.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.