WenmarOpen by Wenmar Pro

Service bulletins for the 2016 BMW 330e

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

341 on file from NHTSA, as of 2026-10-19.

By type

By component

Bulletins, newest first
B1122162018-11-05. Service bulletin. ENGINE AND ENGINE COOLING. ?"ENGINE OIL PRESSURE" ON LOW MILEAGE CARS. Check Control Message (CCM-212) states: "Engine Oil Pressure. Stop Carefully" The following codes may be stored in the DME fault memory" 1C2002 - Engine oil pump, pressure too low 1FB801 - CCM (ID212) - Oil pressure Also, the vehicle's mileage is very low (below 60 miles), the fault frequency shows only "one" occurrence; faults are not currently present and cannot be reproduced. CAUSE Unfavorable DME software application."
B8409162018-11-05. Service bulletin. EQUIPMENT. "?SERVICE ACTION: SUPPLEMENTARY PAGE NEEDED IN OWNER'S MANUAL . Operator's manual of affected vehicles does not contain required information on wireless smartphone charging accessory. AFFECTED VEHICLE Vehicles which require this Service Action to be completed will show it as ""Open"" when checked either in the ""Service Menu"" of DCSnet (Dealer Communication System) or with the Key Reader."
B6517152018-11-05. Service bulletin. ELECTRICAL SYSTEM. "?ACTIVE SOUND DESIGN (ASD) INOPERATIVE AFTER PROGRAMMING What's New: ? ISTA/P and ISTA 4 software level that contains the fix added to Correction and Procedure ? F31, F32, F33, F34, F36 vehicles added to Models ? Warranty information updated to include programming fix . After programming with ISTA/P V3.56.1 or ISTA/P V3.60: Active Sound Design (ASD) no longer provides simulated engine sounds. A fault is stored in the Active Sound Design (ASD) module. Fault Code 8053A5 ""ASD; invalid coding data for equalizing"". Invalid ASD coding data in two different versions of ISTA/P."
B6506172018-11-05. Service bulletin. EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.. ?SATELLITE RADIO DETERIORATION IN RECEPTION QUALITY DUE TO NEW CELLULAR FREQUENCIES . INFORMATION Inform the customer that the introduction of these expanded frequencies by the wireless mobile providers may be influencing reception quality. BMW is currently working with the wireless mobile providers in order to improve the quality of reception and help alleviate the issues that are caused by the wireless mobile expanded frequencies. Once we have more information about this situation this service information bulletin will be updated. Currently Satellite Radio is provided by SiriusXM for BMW customers via geosynchronous (GEO) satellites located roughly above the equator. This means that the satellite signal to some parts of the United States can come in at an angle as low as 32 degrees to the horizon. Due to this angle, buildings, hills, trees, highway sound blocking walls or other obstacles might block the satellite signal coming from reaching the vehicle receiver antenna and might cause audio cut outs, unless the wireless provider has installed terrestrial repeaters. Reception quality decreases the further north you travel, as the angle of the incoming signal gets smaller. Also adverse weather conditions might affect reception. At this time, in the event of a customer complaint or inquiry on interference noise: Do not replace any parts Do not program or carry out other work on the vehicle Explain to customer about the new Wireless Communications Service (WCS) signals When investigating Satellite Radio cutouts or a temporary loss of reception: Please compare to a similarly equipped vehicle. Keep in mind the roofline of the vehicle, size of the antenna (sharkfin) and location of the antenna on the vehicle will all affect the strength of the reception. Do not compare a Sport Activity Vehicle (SAV) with a high roofline mounted antenna to a different vehicle such as a coupe or convertible with a much lower mounting point of the antenna. Replace no parts Do not prog
B6506162018-11-05. Service bulletin. ELECTRICAL SYSTEM. ?NBT HEAD UNIT ABORTS IMPORT OF CD Whats New: ? G12 (7 Series) removed ? I01 (i3) removed ? Warranty Section updated for removal of G12 and I01 . While importing a CD to the internal music collection of an NBT head unit the process aborts. You will see 'import error' on the radio display when this occurs. NBT Head Unit software
B5144162018-11-05. Service bulletin. VISIBILITY:REARVIEW MIRRORS/DEVICES. EXTERIOR MIRROR: CREAKING NOISES Whats new: Video link added This Service Information bulletin supersedes SI B51 44 16 dated January 2017. . Creaking noise coming from either or both exterior rearview mirrors when folding in. Video Link: tinyurl.com/z46agg9 Accumulation of dust in the joint gap seal.
B1303152018-11-05. Service bulletin. ENGINE AND ENGINE COOLING. N20, N26, N55, N63TU, S63TU and S55 Engines: Bosch Injector ETK Part Number Error What's New: ? Procedure change: indentifying injector type using an ISTA test plan. . The current version of the ETK incorporates multiple part number errors for the Bosch type injectors. Ordering the injectors by VIN number or manual identification in ETK may result in an incorrect part number.
B1110152018-11-05. Service bulletin. ENGINE AND ENGINE COOLING. ?Service Action: Replace the Thermostat What's New: ? Part number and quantity of coolant has been updated. Refer to the Warranty section for details. . The Service Engine Soon light is on with corresponding fault codes in the DME for the engine thermostat.
B6202172018-11-05. Service bulletin. ELECTRICAL SYSTEM. ?SeriesOptionDescription F22, F23, F30, F31, F32, F33, F34, F36, F25, F26, F48, 05AR Traffic Jam AssistantX. Sporadically, at low temperatures, the instrument cluster (KOMBI) is not operating (display remains black). KOMBI software.
B6103172018-11-05. Service bulletin. ELECTRICAL SYSTEM. "CHANGE TO PHEV HV BATTERY CELL MODULES. INFORMATION There has been a change to all Generation 3 PHEV high-voltage (HV) battery cell modules. The number of temperatures sensors on the cell modules has decreased from 4 sensors to 3 sensors. This change has to be taken into account when replacing a component within the HV battery that requires the charging or discharging of a cell module with the Deutronic DBL1200HV-60 cell module charger. When connecting the cell module to the charger the number of temperature sensors (NTC's) will need to be changed to 3 for the charger to charge the module correctly. Refer to the DBL1200HV-60 manual for more information (Attached). To verify how many temperature sensors are on the cell module use the ""Diagnosis"" function of the DBL1200HV-60 cell module charger. The example to the right shows 3 temperature sensors. The message ""ZKS not connected"" will be displayed if the incorrect amount of temperature sensors (NTC's) is selected."
B6103152018-11-05. Service bulletin. ELECTRICAL SYSTEM. ?Various Check Control Messages Caused by Shorted K- CAN This Service Information bulletin supersedes SI B61 03 15 dated June 2016. . The customer states that one or more of the following CC messages are displayed: 627 - Steering behavior: Drive moderately 070 - Steering: Drive moderately 765 - Rear-end collision restricted 850 - Pedestrian warning restricted 236 - Driving stabilization: Drive moderately 299 - SOS call system failure 042 - Brake system: Drive moderately After performing a vehicle test, one or more of the following fault codes are stored: ACSM - C9549A Message faulty (seat memory), ACSM receiver, driver's seat module transmitter FEM - D91DE0 No message, receiver FEM, transmitter TMSL FEM - D91EE5 No message, receiver FEM, passenger seat module transmitter ACSM - C9540C Message missing, receiver ACSM, transmitter FEM TMSL - D95402 Message missing, receiver TMSL, transmitter FEM KOMBI - E11454 No message, receiver KOMBI, transmitter REM FEM - D91DE6 No message, receiver FEM, transmitter TMSL TMSR - D99401 Message missing, receiver TMSR, transmitter FEM TMSR - D99402 Message missing, receiver TMSR, transmitter FEM FEM - 8041BA AHL system faulty FEM - D916C3 No message, receiver FEM, transmitter TCB ZBE - E2D403 No message, receiver CON, transmitter FEM-ZGM TRSVC - CA9428 Message incorrect, receiver TRSVC, transmitter PDC-REM TMSL- D95401 Message missing, receiver TMSR, transmitter FEM HU-H - S0397 MOST configuration was not stored TCB - E1445F KCAN2 or KCAN4: Line fault/electrical fault FEM - 8041B6 LWR faulty REM - E58468 Body CAN2; communication fault TRSVC - CA9427 Message incorrect, receiver all around vision camera, transmitter PDC/REM FEM - D91CEC Message missing, receiver FEM, transmitter REM Shorted K-CAN wiring under driver or passenger seat Shorted K-CAN2 wires were shorted between the left side trunk trim panel and the body of the vehicle Shorted K-CAN in left rear wheel well area Shorted K-CAN under center console trim Shorted K-CAN und
B6101172018-11-05. Service bulletin. ELECTRICAL SYSTEM. MALFUNCTION INDICATOR LAMP ILLUMINATED/ EME FAULT . Malfunction Indicator Lamp (MIL) is illuminated. Fault codes stored: EME 2230ED - DOBD - OBC - Signal AVL_U_HVSTO (Status HVSTO, 0x112) invalid receiver SLE, transmitter SME OBC: CE1416-Signal AVL U HVSTO (Status HVSTO, 0x112) invalid receiver SLE, transmitter SME Software insufficiency in the Convenience Charging Electronics (OBC).
B5209162018-11-05. Service bulletin. SEATS. ?REAR SEAT RATTLE . Rear bench seat backrest rattles when driving on uneven roads. Rear bench seatback rattles between the attachment points and retaining clip contact surfaces.
B5203172018-11-05. Service bulletin. ELECTRICAL SYSTEM; SEATS. ?MISSING AUDIO NOTIFICATION WHEN STORING SEAT MEMORY . When saving seat memory settings (Memory 1 or Memory 2) with a vehicle without navigation, there is no audio tone confirmation. Software error in control unit of Seat Module 2.
B3105142018-11-05. Service bulletin. SUSPENSION. ?FRONT SUSPENSION RIDE HEIGHT HAS DROPPED . INFORMATION Please refer to the Electronic Parts Catalog (EPC), using the VIN to locate the part numbers. WARRANTY INFORMATION Damages due to outside influences are not covered under the terms of the BMW limited warranties.
B2401172018-11-05. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION; POWER TRAIN. "?AUTOMATIC TRANSMISSION DRIVEABILITY COMPLAINTS . Hesitant drive off, sluggish driving behavior. The Automatic Transmission (AT) switches into emergency mode and operates only in first gear, Manual shifting (+/-) in Sport Program (using both gear selector and/or shift paddles) is not possible. 44E257 - ""N6 speed sensor: Direction of rotation invalid"" is stored in transmission control module Transmission Control Unit (GKEG3HY) software"
B1803102018-11-05. Service bulletin. ENGINE; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM. "? NO REGENERATION OF THE DIESEL PARTICULATE FILTER (DPF) This Service Information bulletin supersedes SI B18 03 10 dated November 2010. . The Service Engine Soon lamp is illuminated. The following fault codes may be stored in the DDE: N47T/N57T engine 245700 - Particle filter system: particulate filter highly loaded (Exhaust backpressure high) 245800 - particle filter system - filter is heavily contaminated. (exhaust backpressure is above maximum) M57Y engine 480A Particle filter system - filter is heavily contaminated. (exhaust backpressure is too high) 481A Particle filter system - filter is heavily contaminated. (exhaust backpressure is above maximum) CAUSE 1. Faults with the exhaust system that affect the monitoring of the DPF by the DDE 2. Unfavorable recent driving profile INFORMATIOM During normal driving, there is a continuous regeneration of the diesel particulate filter that takes place at exhaust-gas temperatures between 280 and 350°C (slower oxidation process). The soot particles can only be burned off when the required exhaust-gas temperature has been reached. Under certain driving conditions (i.e., prolonged short trips or an exhaust system which never reaches soot burn-off temperatures), the DPF can become restricted. The DDE will initiate periodic regeneration automatically, at the latest after 600 miles. In vehicles making many short distance journeys, periodic regeneration takes place after only 250-500 miles. The Digital Diesel Electronics control unit evaluates the time for periodic regeneration from the following values: average distance driven average driving speed temperature in the diesel particulate filter values from the exhaust pressure sensor The DDE initiates the regeneration process by decreasing incoming air by the throttle valve, and one or two post injections are executed. This heats the exhaust-gas temperature to approx. 600° C . When the exhaust temp reaches this point: The soot is burned off with the residual oxygen. The
B1801172018-11-05. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM; ENGINE. "? DIESEL PARTICULATE FILTER (DPF) CLEANING . The following performance issues may be noticed by the customer: CC-Message ""Drive faulty"" Engine jerking or a lack of power over the whole engine speed range Malfunction indicator lamp (MIL) is illuminated The following fault codes may be stored in the DDE: N47T/N57T engine Main Faults: 245700 - Particle filter system: particulate filter highly loaded (Exhaust backpressure high) 258300 - Exhaust backpressure sensor, Signal: Signal too high Secondary Faults: 244C00 - Charging pressure control, control deviation: charging pressure too low/positive deviation 25DA00 - Exhaust gas difference pressure sensor particle filter, Signal: short circuit to plus pole M57Y engine Main Faults: 480A particle filter system 481A particle filter system Secondary Faults: 4530 charging pressure control, control deviation 429A charging pressure control low pressure stage, control deviation Clogged DPF."
B1227162018-11-05. Service bulletin. ENGINE; ELECTRICAL SYSTEM; ELECTRICAL SYSTEM:12V/24V/48V BATTERY. "? DIAGNOSING NON FUNCTIONING ""eDRIVE"" This Service Information bulletin supersedes SI B12 27 16 dated November 2016. The customer complains that the vehicle will not go into ""eDrive"", and in some cases ""eDrive"" is greyed-out in the control display (CID) and is not selectable. Also, there are no pertinent electric drivetrain fault codes that assist with diagnosis. Possible 12 volt battery failure, Intelligent Battery Sensor (IBS) failure or MSA deactivation."
B1201172018-11-05. Service bulletin. ELECTRICAL SYSTEM; ENGINE. "?SI Engine Electrical Systems B12 01 17 Technical DRIVE POSITION OR ELECTRIC DRIVING IS NOT POSSIBLE . With engine running, it is impossible to: Select Drive with gear selector Utilize electric motor One or more of the following CC messages is shown: ""Hybrid system malfunctioning!"" (ID: 585) ""Drive. No restart"" (ID: 586) Error condition is cleared (vehicle can be driven) after vehicle is in sleep mode for approximately 16 minutes. Software incompatibility."
B1117162018-11-05. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:TURBO/SUPERCHARGER. ?VOLUNTARY EMISSIONS RECALL CAMPAIGN 16E-A05 - N26 ENGINE: REPLACE TURBOCHARGER OIL SUPPLY LINE . Carbonization of the turbocharger sealing ring can cause the exhaust to smoke briefly during cold start up.
B6407182018-10-09. Service bulletin. ELECTRICAL SYSTEM. STATIONARY CLIMATE CONTROL NOT POSSIBLE WHEN SET FOR DEPARTURE TIME BETWEEN 0:00 AND 0:30 TIME RANGE: The programmed stationary climate control ventilation function does not switch on when the departure time is set between 0:00 and 0:30 time range (With the vehicle time setting set to 24 hour).
B6124172018-10-09. Service bulletin. STEERING. STEERING WHEEL BUTTONS DO NOT FUNCTION RELIABLY: Sporadic or continuous malfunction of multifunction steering wheel buttons
B6111182018-10-09. Service bulletin. ELECTRICAL SYSTEM. AFTER EXCHANGING THE FRONT ELECTRONIC MODULE (FEM), PROGRAMMING / ENCODING IS NOT POSSIBLE: After replacing the Front Electronic Module (FEM) for an applicable repair, programming / encoding is not possible.
B8402142018-10-09. Service bulletin. EQUIPMENT. CONNECTEDDRIVE/BMW ASSIST SYSTEM DIAGNOSIS INFORMATION: ConnectedDrive/BMW Assist features are partially or completely inoperative.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.