WenmarOpen by Wenmar Pro

Service bulletins for the 2013 BMW 320i

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

564 on file from NHTSA, as of 2026-10-19.

By type

By component

Bulletins, newest first
1220122018-12-03. Service bulletin. ENGINE AND ENGINE COOLING. N55 Engine: DME FC 160502 Crankcase Ventilation Heater Activation. The Service Engine Soon lamp is NOT illuminated. When diagnosing the vehicle for a customer complaint, the following fault is stored in the DME fault memory. FC 160502 Crankcase ventilation heater, activation: short circuit to ground. This is an erroneous fault that can be ignored.
6115132018-12-03. Service bulletin. ELECTRICAL SYSTEM. "ACSM and ICM Warning Lamps Are Illuminated. Various warning lamps and check control messages relating to the ACSM and ICM systems are illuminated. Many ""No Message"" faults are stored for various control modules. The ACSM and ICM modules may also not be responding to a vehicle test in ISTA. CAUSE Ground point Z10*10B is loose."
6114132018-12-03. Service bulletin. STEERING. Noise from Steering Column Switch Cluster when Turning. A scraping noise is heard from the SZL (Steering Column Switch Cluster) area. This occurs when turning the wheel from 30 to 60 degrees. CAUSE The unlocking pin in the SZL makes contact with the steering wheel.
1702122018-12-03. Service bulletin. ENGINE AND ENGINE COOLING. SI B17 02 12 October 2013 Cooling SystemsTechnical Service This Service Information bulletin supersedes SI 17 02 12 dated November 2012. designates changes to this revision SUBJECT Low Coolant Warning Is Displayed.
1304132018-12-03. Service bulletin. FUEL SYSTEM, GASOLINE. N55 Engine: Erroneous Service Engine Soon Lamp Illuminated with Mixture Faults Stored in the DME. INFORMATION An error has been identified in the current version of ETK regarding N55 fuel injector replacement part numbers and production dates. Installing the incorrect injector part number can lead to an erroneous Service Engine Soon lamp illumination and various mixture faults stored in the DME. Correct part numbers and applicable production dates: P/N 13 64 7 639 994 is for all vehicles produced from 7/2013 P/N 13 64 7 597 870 is for all vehicles produced from 1/2011 to 7/2013 P/N 13 53 7 568 607 is for all vehicles produced to 1/2011 It is good practice to verify that the part number being removed from the engine matches the new injector part number, until further notice. When the ETK data is corrected, a notification will be distributed.
6305122018-12-03. Service bulletin. EXTERIOR LIGHTING. Tail Lamp Is Loose in theTrunk Lid. The customer may notice the tail lamp is either loose or protruding outward from the trunk lid. CAUSE The tail lamp is not attached to the trunk lid properly.
6128122018-12-03. Service bulletin. ELECTRICAL SYSTEM. "Key Intermittently Not Detected and Not Possible to Start Engine. Intermittently it is not possible to start the engine. Terminal 15 cannot be switched on. The remote control key is not detected inside the vehicle. The following check control messages are displayed: * ""Remote control not present or disrupted. Not possible to start engine"" * ""No remote control. Not possible to start engine"" Note: The vehicle can still be started via the emergency start coil on the side of the steering column. Front Electronic Module (FEM) software error"
6107132018-12-03. Service bulletin. STRUCTURE. "Service Action: Repair Corrosion Protection on the Trunk B+ Connector. The corrosion protection on the outside of the trunk (back of rear right-hand wheel arch) around the battery positive connector is insufficient, and leads to corrosion on the body. AFFECTED VEHICLES This Service Action involves F30 vehicles which were produced from 9/2011 to 10/2012. In order to determine whether a specific vehicle has had this Service Action completed or is affected by this Service Action, first check the B-pillar label for code number 645. If code number 645 has been punched out, the campaign has already been performed. If code number 645 has not been punched out, it will be necessary to utilize the ""Service Menu"" of DCSnet (Dealer Communication System) or the Key Reader. Based on the response of the system, either proceed with the corrective action or take no further action."
3407132018-12-03. Service bulletin. SERVICE BRAKES. Brake Fluid Maintenance Service: 36-Month Interval. The CBS displays the first brake fluid service as a 36-month interval from the date of production instead of the appropriate 24-month interval.
3204132018-12-03. Service bulletin. STEERING. Squeaking Noises when Steering Wheel Is Turned. There are squeaking noises from the steering spindle when the steering wheel is turned. The steering spindle gaiter is insufficiently lubricated.
1206132018-12-03. Service bulletin. ENGINE AND ENGINE COOLING. The Service Engine Soon Lamp On with Post Oxygen Sensor Faults Stored. The Service Engine Soon (MIL) lamp is on and the following faults are stored in the DME fault code memory. BN2000 (E-Series) vehicles: * 2D22: Oxygen sensor downstream of catalytic converter, electric: open circuit BN2020 (F-Series) vehicles: * 12AB04: Oxygen sensor downstream of catalytic converter, electric: open circuit * 12AC04: Oxygen sensor downstream of catalytic converter 2, electric: open circuit These faults may occur sporadically after a long MSA engine stop. Unfavorable DME software diagnostics (fault is erroneous) This software error affects vehicles produced from 3/2013 to 6/2013, as well as older vehicles which have been programmed during service work to a current integration level of Xxxx-13-03-5xx.
BMWNOV06132018-12-03. Service bulletin. TIRES. Service Information bulletin B36 03 13 has been published for the Delivery Stop issued on Wednesday, November 13. The Delivery Stop affects certain 2014 model year F30, F31 and F32 October 2013 production vehicles. Tire Identification numbers (molding number and DOT number) must be checked and if necessary, affected tires replaced. Affected vehicles in center inventory must not be delivered until the tires have been checked. The small number of affected vehicles can be identified via the Key Reader, DCS Inquiry or ISPA with the description: Defect Code 0036820100, Delivery Stop, B36 03 13 Check Tire ID
8408132018-12-03. Service bulletin. EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.; EQUIPMENT. "USB Connection Not Working. One, or both of the scenarios listed below may be encountered: 1. The message ""Device not supported"" is displayed in the CID after connecting a USB device to the USB port using a USB cable. 2. The ""USB option"" in the menu cannot be selected (grayed out), after the vehicle was programmed with ISTA/P 2.50.2, or 2.50.3: I-Level F020-13-07-503, or F020-13-07-505. CAUSE 1. Incompatible USB cable is being used 2. Head Unit Basic software error 1 The following procedure should be performed for ""Situation 1, Cause 1"" listed above: Part A (Steps 1 to 3) 1. Duplicate the issue. 2. Verify that the USB cable which is being used, is the original cable for the device and not an aftermarket cable. 3. If the issue is resolved when using an original USB cable supplied by the manufacturer of the device, do not perform step 4 listed below. No further action is required. Part B (Step 4) 4.If the issue is still present when using the original cable from the device manufacturer, proceed to program and code the vehicle using ISTA/P 2.51.0 or higher. ? I-Level after programming would be F020-13-11-501, or higher. Note that ISTA/P will automatically reprogram and code all programmable control modules that do not have the latest software. For information on programming and coding with ISTA/P, refer to CenterNet / Aftersales Portal / Service / Workshop Technology / Vehicle Programming."
6518132018-12-03. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM. Touchpad Integrated in the iDrive Controller Is Intermittently Inoperative. Intermittently the Touchpad integrated in the iDrive controller is inoperative. * No entries can be made using the Touchpad * Fault code is stored in the touch-box control unit Software error in the touch-box control unit (TBX)
6406132018-12-03. Service bulletin. EQUIPMENT:APPLIANCE:AIR CONDITIONER; ENGINE AND ENGINE COOLING. A/C Cooling: Intermittent Reduction of Air Flow. The customer may complain of reduced air flow when the air conditioning system is operated for an extended time, usually longer than one hour. The complaint can vary due to one or more of the following variables: * High outside ambient temperature * Too much humidity * A/C temperature and fan settings set too low for too long Note: It is very difficult to duplicate this issue due the required outdoor weather conditions and length of driving time needed. CAUSE Evaporator starts to freeze up due to the position of the evaporator temperature sensor
6307132018-12-03. Service bulletin. ELECTRICAL SYSTEM; EXTERIOR LIGHTING. Daytime Running Light Does Not Switch ON. The DRL (Daytime Running Light) is off and cannot be switched on after importing the personal profile from another vehicle. The CID (Central Information Display) display shows that it is active. CAUSE Software error when importing the personal profile from a vehicle which has a different head unit
6123132018-12-03. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM; EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. Integrated Owner's Manual No Longer Available After Programming. After a programming or replacement of the Front Electronics Module (FEM), the customer states that the Integrated Owner's Manual (IBA) can no longer be selected in the vehicle. CAUSE FEM application error
3603132018-12-03. Service bulletin. TIRES. "?PERFORM THE PROCEDURE OUTLINED IN THIS SERVICE INFORMATION ON ALL AFFECTED VEHICLES BEFORE CUSTOMER DELIVERY OR THE NEXT TIME THEY ARE IN THE SHOP FOR MAINTENANCE OR REPAIRS. SUBJECT Service Action: Continental Tires, Inspect and Replace if Necessary. During manufacturing process of the Continental tires, there may have been a deviation from the production specifications. AFFECTED VEHICLES This Service Action involves F30, F31 and F32 vehicles. In order to determine whether a specific vehicle has had this Service Action completed or is affected by this Service Action, first check the B-pillar label for code number 659. If code number 659 has been punched out, the campaign has already been performed. If code number 659 has not been punched out, it will be necessary to utilize the ""Service Menu"" of DCSnet (Dealer Communication System) or the Key Reader. Based on the response of the system, either proceed with the corrective action or take no further action."
3403132018-12-03. Service bulletin. SERVICE BRAKES, HYDRAULIC. Incorrect Remaining Service Life from CBS Data for Brake pads. The calculated remaining service life for the brake pads (front and/or rear axle) from the CBS data does not match the actual brake pad thickness. The customer notices implausible remaining distances (too high or too low) on the front and/or the rear axle brake system. Note: E9x vehicles with xDrive are not affected by this bulletin. Software calculation in the brake pad wear model
1217132018-12-03. Service bulletin. ENGINE; POWER TRAIN. N55: Engine Difficult to Start at Cold Ambient Temperatures. The complaint may include any of the following symptoms: * The engine stalls immediately after a cold start before driving away * The engine may run roughly or misfire after a cold start * The engine does not start cold or may take several attempts * To assist starting when cold, the accelerator may need to be depressed slightly and the idle speed raised for a few seconds so the engine does not stall This can occur most frequently at outside ambient temperatures between -15°C and + 15°C. It is possible that the Service Engine Soon (MIL) lamp is on with misfire fault(s) stored, but it is equally possible that there will be no faults stored in the DME. Unfavorable DME software Cold start or idling problems may arise due to poor fuel quality. The use of summer fuel during cold outside temperatures may also lead to such problems.
1201132018-12-03. Service bulletin. ENGINE; POWER TRAIN:AUTOMATIC TRANSMISSION. MN16 Engine: FC 2D9B Knock Sensor, Signal Is Stored in the DME. Certain areas of the US experience extremely cold climate conditions during the winter months, which can cause the Service Engine Soon lamp to illuminate while the engine temperature is increasing to full operating temperature. The following fault may be stored in the DME: ??FC 2D9B Knock Sensor, Signal CAUSE Unfavorable DME knock sensor diagnostic at outside ambient temperatures below -5° C
6510092018-12-03. Service bulletin. EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM); EQUIPMENT. The vehicle position is missing or incorrect on the navigation map. The navigation system integrated in the Car Information Computer (CIC) is not calibrated correctly.
6102112018-12-03. Service bulletin. ELECTRICAL SYSTEM. Advanced Onboard Battery Diagnostics. INFORMATION Starting with the introduction of the F10 (5 Series), an advanced intelligent battery sensor has been used. This now makes it possible for the vehicle to monitor the condition of the battery in order to determine if the battery needs to be recharged or replaced, along with the remaining capacity of the battery. The analysis and testing of the battery's SoC (State of Charge) and SoH (State of Health) is now performed using ISTA (Integrated Service Technical Application) diagnosis. A separate test using a battery tester is no longer needed.
3403132018-12-03. Service bulletin. SERVICE BRAKES, HYDRAULIC. ncorrect Remaining Service Life from CBS Data for Brake pads. The calculated remaining service life for the brake pads (front and/or rear axle) from the CBS data does not match the actual brake pad thickness. The customer notices implausible remaining distances (too high or too low) on the front and/or the rear axle brake system. Software calculation in the brake pad wear model
1701132018-12-03. Service bulletin. ELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING. Service Action: Replace Coolant Expansion Tank. The low coolant level warning may come on in the information display. CAUSE Insufficient contact at the electrical connector for the coolant level sensor causes an inaccurate reading of the coolant level.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.