WenmarOpen by Wenmar Pro

Service bulletins for the 2013 BMW 320i

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

564 on file from NHTSA, as of 2026-10-19.

By type

By component

Only bulletins with component: Electrical system are shown. Show all

Bulletins, newest first
B6517152018-11-13. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT:ELECTRICAL; EQUIPMENT. "Active Sound Design ASD inoperative after programming. After programming with ISTA/P V3.56.1 Active Sound Design (ASD) no longer provides simulated engine sounds A fault is stored in the ASD module. Fault Code 8053A5 ""ASD; invalid coding data for equalizing"" Invalid ASD coding data"
B6516152018-11-13. Service bulletin. EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM); ELECTRICAL SYSTEM. Navigation CIC vehicle positioning temporarily incorrect. The Navigation system may temporarily display the vehicle in the wrong location. This mainly occurs on short sections of road and the vehicle position may take 2 or more minutes to be shown correctly. Invalid calculation in the CIC head unit.
B6126142018-11-13. Service bulletin. ELECTRICAL SYSTEM; ELECTRICAL SYSTEM:HORN. "Horn(s) Fail to Work. While trying to activate the horn, one or both horns fail to work. One or more of the following fault codes can be stored in the FEM: ? ""8044A3 - Wiring, horn short circuit to earth"" ? ""8044A4 - Wiring, horn short circuit to positive"" ? ""8044A5 - Wiring, horn relay is defective or short circuit to positive"" Water has entered the horn and caused it to fail internally (shorted out)."
1224132018-11-13. Service bulletin. ELECTRICAL SYSTEM; ENGINE. "PERFORM THE PROCEDURE OUTLINED IN THIS SERVICE INFORMATION ON ALL AFFECTED VEHICLES BEFORE CUSTOMER DELIVERY OR THE NEXT TIME THEY ARE IN THE SHOP FOR MAINTENANCE OR REPAIRS. BMW centers must ensure Recalls are completed after having been notified by BMW of North America, LLC (BMWNA) that a safety-related defect or noncompliance exists in any motor vehicle or item of replacement equipment in the center's possession at the time of notification. In BMW NA's case, this notification would typically be made by the issuance of a Recall notification in the form of a Service Information bulletin (SIB) or transmission of a Dealer Communication System (DCS) Recall message. Under the National Traffic and Motor Vehicle Safety Act of 1966, as amended, if a Recall Campaign is announced by BMW NA, centers must ensure that all Recalls on new vehicles and new items of replacement equipment are completed BEFORE delivery to the consumer. This means that centers may not legally deliver new motor vehicles or new items of replacement equipment to consumers with an open Recall. The Safety Act also prohibits centers from selling or leasing the motor vehicle or item of replacement equipment, unless and until the open Recall has been completed BEFORE delivery. This also pertains to vehicles in the Certified Pre-Owned program, and to items of replacement equipment. Finally, BMW centers should not sell or use parts that have been recalled by BMW NA. Please follow the specific instructions provided by BMW NA on the return or disposition of the parts. designates changes to this revision SUBJECT Voluntary Emissions Recall Campaign 13E-A03: Program Control Units (OBD). Due to an error in the DME (Digital Motor Electronics) software, the required oxygen sensor onboard diagnostics (OBD) is not functioning. As a result, the ""Readiness bit"" confirming a successful completion of the oxygen sensor diagnostics will not be set. In order to remedy the situation, BMW is conducting a Voluntary Emissions
1235142018-11-13. Service bulletin. ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL; ELECTRICAL SYSTEM:SOFTWARE; ENGINE. This Service Information bulletin supersedes SI B12 35 14 dated December 2014. designates changes to this revision SUBJECT N20, N26 Service Engine Soon Light On: Fault Code 1B9702 is Stored. The Service Engine Soon light (MIL) is on with only the following fault stored in the DME: z 1B9702: Engine switch-off time, timer, instrument panel timer DME, Comparison: Value of instrument panel timer too low while engine is running This fault will not cause any engine running or drivability problems. Instrument cluster software error.
1204152018-11-13. Service bulletin. ELECTRICAL SYSTEM; ENGINE. SUBJECT DME Internal and Valvetronic Faults Set at Cold Ambient Temperatures. The Service Engine Soon light (MIL) can be illuminated with the erroneous internal and Valvetronic faults stored in the DME. The MIL will only come on if the fault has been detected on two (or more) consecutive drive cycles. The following fault codes may be stored in the DME: E Seriesz 36AE - DME, internal fault, Valvetronic: Current implausible One or more of the following secondary faults may also be stored: z 2DE2 - Valvetronic, actuation, voltage phase: Line disconnection z 2DE3 - Valvetronic, actuation, volt phase: Line disconnection z 2DE4 - Valvetronic, actuation, volt phase: Line disconnection F Seriesz 1F0905 - DME, internal fault, Valvetronic: Current implausible One or more of the following secondary faults may also be stored: z 135B10 - Valvetronic, actuation, voltage phase: Line disconnection z 135B11 - Valvetronic, actuation, volt phase: Line disconnection z 135B12 - Valvetronic, actuation, volt phase: Line disconnection Engine performance and driving characteristics are not affected. DME software diagnostic sensitivity.
B6113162018-11-13. Service bulletin. ELECTRICAL SYSTEM. "KLE CHARGING FAULT 21E6E9. During the ISTA short test diagnosis, fault code 21E6E9 - ""Charging interruption"" is found stored in the KLE (Convenience Charging Electronics) module. There is no customer complaint related to charging system, or a warning check control message display. CAUSE An Erroneous fault 21E6E9 stored in the KLE after completion of AC charging session."
B1221142018-11-05. Service bulletin. FUEL SYSTEM, OTHER:STORAGE:FUEL GAUGE SYSTEM; ELECTRICAL SYSTEM:SOFTWARE; FUEL SYSTEM, GASOLINE. Engine Malfunction Warning Illuminated with FC 193208: Fuel Level Plausibility Stored in DME. The customer states that the engine malfunction warning lamp is illuminated, and while filling the fuel tank, the fuel gauge did not show the proper fill level. After the vehicle is driven a short distance, the fuel gauge will update to full. When diagnosed, the following fault is stored in the DME: ? FC 193208 Fuel level, plausibility: deviation between consumption and level change Please proceed to the Procedure section. Vehicles with option 610 (Head-Up Display) are not affected. Please follow the ISTA/D test plan for the applicable faults stored in the DME, including the one listed in this bulletin. CAUSE A software error in the instrument cluster causes the fuel gauge to incorrectly update while refilling. The error occurs when the vehicle is powered up after refilling.
B6103142018-11-05. Service bulletin. ELECTRICAL SYSTEM. Check Control Messages Related to Battery Charge During Cold Ambient Temperatures. On cold days with an outside ambient temperature of less than 15°F, customers may notice a check control message related to the battery that is displayed on the instrument cluster and the control information display. Under these conditions, the vehicle starts. Various power management faults can occur. The check control message (ID 229) is caused by a heavily discharged battery. ? The check control message is triggered when the current state of charge (SoC) of the battery approaches the minimum SoC that is required to start the vehicle (start capability limit). ? In low outside ambient temperatures, the start capability limit of the vehicle is higher. Therefore it takes more energy from the battery to start a cold engine. ? Without the early warning of the check control message, the current state of charge would drop below the start capability limit and the vehicle would not start. ? The vehicle's intelligent power management system actively takes measures to increase the charge of the battery, such as increasing idle speed and reducing or shutting down certain electrical consumers.
B2702152018-11-05. Service bulletin. ELECTRICAL SYSTEM; POWER TRAIN. Rattling Noise from Transmission Tunnel. A rattling or knocking noise is heard in the area of the gear selector switch (GWS) during engine load reversal. CAUSE The vent tube for the transfer case is making contact with the transmission tunnel.
B1221142018-11-05. Service bulletin. ELECTRICAL SYSTEM. ?SI B12 21 14May 2015 Engine Electrical SystemsTechnical Service This Service Information bulletin supersedes SI B12 21 14 dated April 2015. designates changes to this revision SUBJECT Engine Malfunction Warning Illuminated with FC 193208: Fuel Level Plausibility Stored in DME. The customer states that the engine malfunction warning lamp is illuminated, and while filling the fuel tank, the fuel gauge did not show the proper fill level. After the vehicle is driven a short distance, the fuel gauge will update to full. When diagnosed, the following fault is stored in the DME: ? FC 193208 Fuel level, plausibility: deviation between consumption and level change Please proceed to the Procedure section. Vehicles with option 610 (Head-Up Display) are not affected. Please follow the ISTA/D test plan for the applicable faults stored in the DME, including the one listed in this bulletin. CAUSE A software error in the instrument cluster causes the fuel gauge to incorrectly update while refilling. The error occurs when the vehicle is powered up after refilling.
6103142018-11-05. Service bulletin. ELECTRICAL SYSTEM; POWER TRAIN. Check Control Messages Related to Battery Charge During Cold Ambient Temperatures. On cold days with an outside ambient temperature of less than 15°F, customers may notice a check control message related to the battery that is displayed on the instrument cluster and the control information display. Under these conditions, the vehicle starts. Various power management faults can be stored. When the outside temperatures drop below 46°F, the charging system is switch to full charge. CAUSE ? The check control message (ID 229) is caused by a heavily discharged battery. ? The check control message is triggered when the current state of charge (SoC) of the battery approaches the minimum SoC that is required to start the vehicle (start capability limit). ? In low outside ambient temperatures, the start capability limit of the vehicle is higher. Therefore it takes more energy from the battery to start a cold engine. ? Without the early warning of the check control message, the current state of charge would drop below the start capability limit and the vehicle would not start. ? The vehicle's intelligent power management system actively takes measures to increase the charge of the battery, such as increasing idle speed and reducing or shutting down certain electrical consumers.
1221142018-11-05. Service bulletin. ENGINE; ELECTRICAL SYSTEM. SI B12 21 14February 2015 Engine Electrical SystemsTechnical Service This Service Information bulletin supersedes SI B12 21 14 dated December 2014. designates changes to this revision SUBJECT Engine Malfunction Warning Illuminated with FC 193208: Fuel Level Plausibility Stored in DME. The customer states that the engine malfunction warning lamp is illuminated, and while filling the fuel tank, the fuel gauge did not show the proper fill level. After the vehicle is driven a short distance, the fuel gauge will update to full. When diagnosed, the following fault is stored in the DME: z FC 193208 Fuel level, plausibility: deviation between consumption and level change Please proceed to the Procedure section. Vehicles with option 610 (Head-Up Display) are not affected. Please follow the ISTA/D test plan for the applicable faults stored in the DME, including the one listed in this bulletin. CAUSE A software error in the instrument cluster causes the fuel gauge to incorrectly update while refilling. The error occurs when the vehicle is powered up after refilling.
B6618162018-11-05. Service bulletin. ELECTRICAL SYSTEM. INFORMATION ON THE OPERATION OF THE SMART OPENER. INFORMATION ON THE OPERATION OF THE SMART OPENER MODEL F07 (5 Series Gran Turismo) F10 (5 Series) F12 (6 Series Convertible) F13 (6 Series Coupe) F15 (X5) F16 (X6) F22 (2 Series Coupe) F23 ( 2 Series Convertible) F25 (X3) F26 (X4) F30 (3 Series Sedan) F31 (3 Series Wagon) F32 (4 Series Coupe) F33 (4 Series Convertible) F34 (3 Series Gran Turismo) F36 (4 Series Gran Coupe) F48 (X1) F80 (M3 Sedan) F82 (M4 Coupe) F83 (M4 Convertible) F85 (X5 M) F86 (X6 M) G12 (7 Series) I01 (i3 Series) Vehicles with option code SA-0322 (Comfort Access) without M-Sport trim INFORMATION The smart opener (Contactless tailgate) operates as described below: Ignition key must be within 3 feet behind the vehicle, clear from any interference like a smartphone The customer must be at least an arms-length behind the vehicle Kick your foot forwards & backwards under the vehicle in one quick movement The taillights flash confirming that the trunk will open The trunk then successfully opens For more information an instructional video can be viewed which demonstrates the operation. Thanks to BMW of Tenafly for providing the video. tinyurl.com/Autotrunk1 https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/358...9/3/2016 Page 2 of 2 WARRANTY INFORMATION Not applicable. [ Copyright (c)2016 BMW of North America, Inc. ] https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/358...9/3/2016
B0107162018-11-05. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM. "N20 LEAK DIAGNOSIS MODULE (NVLD): LIMITED WARRANTY EXTENSION TO 10 YEARS/120,000 MILES. INFORMATION For the eligible vehicles, BMW of North America, LLC (""BMW NA"") is extending the limited warranty for the leak diagnosis module (NVLD) to: 10 years/120,000 miles as determined by the vehicle's original in-service date Recall or Service Action. There is no immediate repair required unless the BMW vehicle is currently experiencing this problem. Customer Notification Letter - VIN and Component-specific Warranty Extension Even though this is NOT a Recall, BMW NA will be sending VIN-specific customer notification letters in a phased release."
B6526162018-11-05. Service bulletin. EQUIPMENT; EQUIPMENT ADAPTIVE/MOBILITY; ELECTRICAL SYSTEM. "USB DEVICE IS NOT DETECTED BY CHAMP2 HEAD UNIT. Media connected to the USB connector is not recognized by the audio system. Playback of files from the media is not possible. Message displayed on the audio system display: ""Title cannot be reproduced"" ""Is being read"" (but never plays back any audio) CAUSE Media with data files stored in more than 32 directories or 32 subdirectories within a directory. Media with a large number of files. Media exceeds total storage capacity of 32 GB."
B0905152018-11-05. Service bulletin. EXTERIOR LIGHTING; ELECTRICAL SYSTEM. Front Parking Lights Inoperative. After programming the vehicle with ISTA/P 3.56.1, both front parking lights (integrated in the headlights) have been deactivated and no Check Control message is displayed. CAUSE FEM software error in ISTA/P 3.56.1
B6523162018-11-05. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; EQUIPMENT; EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.. ?AUDIO VOLUME NOT RESTORED AFTER MSA STOP, ENTRY HEAD UNIT. Volume of audio system (when set to near maximum) is reduced when Auto Start-Stop (MSA) stop occurs and is not restored upon automatic engine restart. This is normal system behavior - serves to protect the head unit, battery drain and avoidance of incremental leaps in the loudness. The loudness is reduced to 2/3 of maximum and is not restored. Note: Air conditioning output is also reduced upon MSA stop and is not restored for similar reasons.
B8404162018-11-05. Service bulletin. ELECTRICAL SYSTEM. SOS MALFUNCTION DISPLAYED. An SOS malfunction is seen in the Kombi. When pressing the E-Call/SOS button in the overhead console, nothing happens. Fault code B7F33C (internal ECU error) is stored in the Telematics control unit (ATM/TCB2). There are 2 known causes for this failure. They are as follows: Software file missing from the ATM/TCB2 control module Water leak at shark-fin leading to corrosion in the ATM/TCB2 control module
B6523142018-11-05. Service bulletin. ELECTRICAL SYSTEM. CENTRAL INFORMATION DISPLAY INTERMITTENTLY FLASHES OFF/ON This Service Information bulletin replaces SI B65 23 14 dated December 2014. Intermittently, the Central Information Display (CID) flashes off/on. Voltage supply error from the Head unit-high (HU-H) to the Central Information Display (CID) when the display brightness is set to 60% or higher
B6308162018-11-05. Service bulletin. EXTERIOR LIGHTING:TURN SIGNAL; ELECTRICAL SYSTEM. TURN SIGNAL - INTERMITTENTLY FLASHES AT FASTER RATE. Turn signal, intermittently, flashes at faster rate or not at all. Software error in FEM (Front Electronics Module)
B0703142018-11-05. Service bulletin. ELECTRICAL SYSTEM. Diagnosing Stored Fault Codes to Help Avoid Repeat Repair Visits This Service Information bulletin supersedes SI B07 03 14 dated October 2015.. Fault codes stored in vehicles being serviced are not being diagnosed, leading to repeat repair visits (source- Analysis of FASTA data and repeat repair visit reports). INFORMATION Where diagnosis (vehicle or short test) with ISTA has already started, it is important to diagnose the fault code(s) listed below (when they are stored in the vehicle) to find their root cause during the current workshop visit. This will help lead to a reduction in workshop repeat repair visits and higher customer satisfaction.
B6136172018-11-05. Service bulletin. ELECTRICAL SYSTEM. "BATTERY DISCHARGE CCM (CHECK CONTROL MESSAGE) DISPLAYED: COMFORT ACCESS DISABLED. One or more of the following conditions are present: * CCM ""Battery. Discharge in standstill."", or similar, is displayed. * Comfort Access and contactless tailgate opening are not working. * Vehicle can still be unlocked with radio remote control (ID transmitter). Fault conditions are cleared upon engine restart. FEM (Front Electronics Module) software error Unauthorized (radio remote control out of range) access to vehicle has been attempted at least seven times with Comfort Access or Smart Opener (contactless tailgate opening) when the vehicle was locked. As a result of these unauthorized access attempts, the following conditions were set: * CCM ""Battery. Discharge in standstill."", or similar, is displayed * Terminal 30F (switched battery terminal when fault occurs) was deactivated, preventing Comfort Access and contactless tailgate opening."
B6103152018-11-05. Service bulletin. ELECTRICAL SYSTEM. VARIOUS CCM (CHECK CONTROL MESSAGES) CAUSED BY SHORTED K-CAN. The customer states that one or more of the following CCM are displayed: * 627 - Steering behavior: Drive moderately * 070 - Steering: Drive moderately * 765 - Rear-end collision restricted * 850 - Pedestrian warning restricted * 236 - Driving stabilization: Drive moderately * 299 - SOS call system failure * 042 - Brake system: Drive moderately After performing a vehicle test, one or more of the following fault codes are stored: * ACSM (Advanced Safety Crash Module) - C9549A Message faulty (seat memory), ACSM receiver, driver's seat module transmitter * FEM (Front Electronics Module) - D91DE0 No message, receiver FEM, transmitter TMSL * FEM - D91EE5 No message, receiver FEM, passenger seat module transmitter * ACSM - C9540C Message missing, receiver ACSM, transmitter FEM * TMSL (Front Light Electronics Left) - D95402 Message missing, receiver TMSL, transmitter FEM * KOMBI - E11454 No message, receiver KOMBI, transmitter REM * FEM - D91DE6 No message, receiver FEM, transmitter TMSL * TMSR (Front Light Electronics Right) - D99401 Message missing, receiver TMSR, transmitter FEM * TMSR - D99402 Message missing, receiver TMSR, transmitter FEM * FEM - 8041BA AHL system faulty * FEM - D916C3 No message, receiver FEM, transmitter TCB * ZBE (Controller) - E2D403 No message, receiver CON, transmitter FEM-ZGM * TRSVC (Control unit for rear view camera and Side View) - CA9428 Message incorrect, receiver TRSVC, transmitter PDC-REM * TMSL - D95401 Message missing, receiver TMSR, transmitter FEM * HU-H (Headunit High) - S0397 MOST configuration was not stored * TCB (Telematics Control Box) - E1445F KCAN2 or KCAN4: Line fault/electrical fault * FEM - 8041B6 LWR faulty * REM (Rear Electronics Module) - E58468 Body CAN2; communication fault * TRSVC- CA9427 Message incorrect, receiver all around vision camera, transmitter PDC/REM FEM - D91CEC Message missing, receiver FEM, transmitter REM * Shorted K-CAN wiring under drive
B6210172018-11-05. Service bulletin. ELECTRICAL SYSTEM. ERRONEOUS SERVICE INCLUSIVE CBS DISPLAY. After pre-delivery check or after instrument cluster exchange, BMW Service Inclusive is displayed although the vehicle does not feature the optional Service Inclusive coverage. Instrument Cluster display error

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.