Service bulletins for the 2020 Bentley Mulsanne
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
115 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
| 2058586/2 | 2020-11-07. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT. Bentayga and Mulsanne - Rear Entertainment Tablet - Battery Replacement. Customer statement / workshop findings: Message on Bentley Rear Entertainment Tablet: The battery is defective Please contact your Bentley dealer. Technical background: The Bentley Rear Entertainment Tablet incorporates battery voltage protection, under certain conditions this system can prevent the internal battery from accepting a charge current, this would normally require the Tablet to be replaced. This TPI provides the necessary information to replace the Tablet internal battery pack. |
|---|---|
| 2060823/1 | 2020-10-06. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT:APPLIANCE:TV/RADIO/SPEAKERS. Radio: Reception complaints. Customer statement / workshop findings: All complaints which are related to radio reception issues Technical background: Complaints about the radio reception can have many causes. The radio reception strength/quality at the vehicle location can be an important issue. To process such complaints as effectively as possible it is important to precisely record the circumstances when a complaint occurs. The attached check list is available for this purpose. Please ensure the instructions within the Measure section are strictly adhered to |
| 2058586/1 | 2020-09-05. Service bulletin. ELECTRICAL SYSTEM. Bentayga and Mulsanne - Rear Entertainment Tablet - Battery Replacement Customer statement / workshop findings Message on Bentley Rear Entertainment Tablet The battery is defective Please contact your Bentley dealer . Bentley Rear Entertainment Tablet will not accept a charge current. Technical background The Bentley Rear Entertainment Tablet incorporates battery voltage protection, under certain conditions this system can prevent the internal battery from accepting a charge current, this would normally require the Tablet to be replaced. This TPI provides the necessary information to replace the Tablet internal battery pack. |
| 2052785/5 | 2020-09-05. Service bulletin. SERVICE BRAKES, HYDRAULIC. Brake noise identification. Customer statement: Noise complaint from the braking system. Workshop findings: The noise can be reproduced and clearly assigned to the braking system. Technical Background: Brake noises can be attributed to many causes. Eight of the most common causes are: 1. Brake discs or pads are close to their wear limit. 2. New brake pads and/or discs have not been properly bedded in after installation. 3. Aftermarket pads or discs are installed. 4. There is debris such as small stones, grit, road salt or sand between the brake disc and pad. 5. Discs are covered in rust. Rust can form when the vehicle has been stationary for long periods of time (Figure 1). |
| 2043897/2 | 2020-08-08. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM:SOFTWARE. Mulsanne - No volume. Customer statement/workshop findings: No volume/sound from the Infotainment system Technical background: Software update required to reinstall the functionality of the sound/volume |
| 2053177/12 | 2020-08-06. Service bulletin. ELECTRICAL SYSTEM. All Vehicle Variants - Spurious DTC List Condition: Customer will not be aware of any fault codes. Workshop may discover spurious fault codes whilst running a Diagnostic Trouble Code (DTC) log as part of other investigations on the vehicle. Technical Background: The attached document contains all of the current known Spurious DTCs for all vehicle variants. Should a particular TPI be listed as Archived within the attached document the TPI can no longer be viewed within Elsa pro, in this case please refer to the instructions with the attached document regarding the DTC description and actions (if any) which should be conducted |
| 2053177/11 | 2020-08-06. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT. Customer statement / workshop findings Customer will not be aware of any fault codes. Workshop may discover spurious fault codes whilst running a Diagnostic Trouble Code (DTC) log as part of other investigations on the vehicle. All Vehicle Variants - Spurious DTC List Technical background The attached document contains all of the current known Spurious DTCs for all vehicle variants. Should a particular TPI be listed as Archived within the attached document the TPI can no longer be viewed within Elsa pro, in this case please refer to the instructions with the attached document regarding the DTC description and actions (if any) which should be conducted |
| 2028808/4 | 2020-08-05. Service bulletin. ENGINE AND ENGINE COOLING. Engine oil. Specific oil type and oil consumption reference. Customer statement / workshop findings: Engine oil level requires to:p up between services. Technical background The use of the correct oil for each engine type is critical for its continued performance, reliability and ultimately warranty. The workshop manual should always be the first point of reference, ensuring the correct lubricant is used for each specific model year and engine type Should oil be required the parts catalogue must be referred to ensuring the correct VIN is always used when ordering |
| 2057841/2 | 2020-08-05. Service bulletin. STRUCTURE. Windscreen replacement criteria whilst under manufacturers warranty. Customer statement / workshop findings: Windscreen cracked/damaged Technical background: Please refer to the instructions within the Measure section of this TPI in the event that a windscreen is cracked/damaged |
| 2056582/3 | 2020-08-05. Service bulletin. STRUCTURE. Interior trim - Creak and rattle - Noise identification. Customer statement / workshop findings: Noise complaint from the interior Workshop findings: The noise can be reproduced and clearly assigned to the interior Prior to starting the instructions within this TPI, the Retailer must check and confirm the vehicle is in standard factory condition and has not had any non-approved aftermarket modifications conducted Should any aftermarket modifications be found, the Retailer must make Product Support aware by raising a DISS query to report the details of the modification, you must then await feedback from Product Support before conducting any further work |
| 2053492/6 | 2020-08-05. Service bulletin. SUSPENSION:REAR:SPRINGS. Air spring fault finding. Customer statement / workshop findings: The front and/or rear suspension appears to have dropped. Technical background: The list of Bentley vehicles below are fitted with air springs as part of the suspension system. Should air leak from the air springs, this will cause the suspension to drop. However, the dropping of the suspension does not necessarily mean that the air spring is faulty. TheMeasure section of this TPI describes how and where to check for air leaks on the front and rear air springs, the air pump compressor, pipes, valve unit and air reservoirs. This includes potential air leak points on the air springs and also the locations of an air leak that can be repaired without the need to replace an air spring. These checks should be carried out in conjunction with the Elsapro procedure Air suspension: To check with the use of the special tool Air suspension leak tester VAS 751 001 shown in the image below as item ( 1). Refer to Elsapro, Repair Group 43, Air suspension To check. |
| 2053177/10 | 2020-07-07. Service bulletin. ELECTRICAL SYSTEM. All Vehicle Variants - Spurious DTC List Condition: Customer will not be aware of any fault codes. Workshop may discover spurious fault codes whilst running a Diagnostic Trouble Code (DTC) log as part of other investigations on the vehicle. Technical Background: The attached document contains all of the current known Spurious DTCs for all vehicle variants. Should a particular TPI be listed as Archived within the attached document the TPI can no longer be viewed within Elsa pro, in this case please refer to the instructions with the attached document regarding the DTC description and actions (if any) which should be conducted Service: During routine diagnostic interrogation of vehicle systems use the attached document to determine the course of action to be taken. |
| 2055254/2 | 2020-02-08. Service bulletin. ELECTRICAL SYSTEM. Top view/Rear view camera - guidelines not visible Condition: Guidelines not showing on display screen when reverse gear selected Technical Background: Due to legal requirements, changes have been made to the visibility of guidelines in the Top view and Rear view camera systems on all vehicles built from May 2018 in the following regions: USA Canada Mexico Puerto Rico On the Top view camera system the guidelines are not visible on first reverse gear selection after engine start, the guidelines are visible on the second selection and thereon after. If the PDC button is pressed the guidelines are always visible. On the Rear view camera system the guidelines are never visible. |
| 2058173/1 | 2020-02-08. Service bulletin. ELECTRICAL SYSTEM. Electrical switch replacement guidelines Customer statement / workshop findings: Electrical switch suspected as defective This TPI is not applicable to suspected faulty control units or any component related to the passive restraint system in particular the airbag system Technical background: Prior to replacing an electrical switch refer to the Measure section of this TPI |
| 2024811/2 | 2020-01-17. Service bulletin. POWER TRAIN; ELECTRICAL SYSTEM. Gearbox code P1703 not clearing in Guided Fault finding Condition: There is no customer complaint the fault code is logged as a result of connecting the diagnostic tester When the fault memory is read using Guided Fault finding the following codes may be logged: P170300 Limp home, control unit reset (located in diagnostic address 02 Transmission control module) U1111 Function limitation due to missing message (located in diagnostic address 81 Gear Shift Control Module (GSM) Technical Background: Due to a communication error between the tester and the transmission control module the above faults may be logged even though there is no problem with the vehicles gearbox system. If these faults are logged and there is no gearbox problem reported, clear these codes using vehicle Self Diagnosis. |
| 2050542/4 | 2020-01-09. Service bulletin. EXTERIOR LIGHTING. Customer statement: 1. The lenses of the headlights (illustration 1a) /front fog lamps (illustration 1b) are steamed up/damp from the inside with minor drips. 2. Water is in the headlight (illustration 2a) / front fog lamp (illustration 2b), big drips. Technical Background 1. Damp air settles on the inner lens of the headlights/fog lamps, with recognisable misting in certain weather conditions (comparable with the steaming up of spectacle lenses when entering a warm room in winter or of the bathroom mirror after a shower). 2. Leak on the headlights/front fog lamps. For example through open covers, a damaged seal of the cap or similar. |
| 2056407/2 | 2020-01-09. Service bulletin. STEERING; SUSPENSION. Condition: Customer statement: Noise complaint from the suspension and/or steering Workshop findings: The noise can be reproduced and clearly assigned to the suspension system from either of the axles And/or The noise can be reproduced and clearly assigned to the steering system Prior to starting the instructions within this TPI, the Retailer must check and confirm the vehicle is in standard factory condition and has not had any non-approved aftermarket modifications conducted including the modification of the engine control modules (chip tuning) Check the history of the vehicle to confirm Should any aftermarket modifications be found, the Retailer must make Product Support aware by raising a DISS query to report the details of the modification, you must then await feedback from Product Support before conducting any further work Technical Background It is the retailers responsibility to check and confirm if any TPIs are applicable to the customers complaint/issue, should an applicable TPI be available, apply it and complete a DISS complaint to include Workshop findings only (No repair query required) For correct diagnosis and repair, the attached Flowchart must be followed in conjunction with the Measure section of this TPI |
| 2051187/5 | 2020-01-09. Service bulletin. ELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING. Condition: Poor engine running, reduced power, engine warning lamp illuminated. Technical Background: Technical Product Information (TPI) to assist Retailers when diagnosing poor engine running or misfires. Service: The following TPI should be carried out sequentially to ensure the root cause and analysis of the concern are identified without unnecessary work or repetitive actions taking place. |
| 2055036/2 | 2020-01-09. Service bulletin. ELECTRICAL SYSTEM. Condition: Complaints relating to My Bentley connected services. Technical Background: Most queries and complaints regarding My Bentley connected services can be resolved by contacting My Bentley Support rather than raising a DISS technical query. |
| 2056582/2 | 2020-01-09. Service bulletin. STRUCTURE. Condition: Customer statement: Noise complaint from the interior Workshop findings: The noise can be reproduced and clearly assigned to the interior Prior to starting the instructions within this TPI, the Retailer must check and confirm the vehicle is in standard factory condition and has not had any non-approved aftermarket modifications conducted Should any aftermarket modifications be found, the Retailer must make Product Support aware by raising a DISS query to report the details of the modification, you must then await feedback from Product Support before conducting any further work Technical Background It is the retailers responsibility to check and confirm if there are any TPIs which are applicable to the customers complaint/issue if there is an applicable TPI available, apply it and complete a DISS complaint to include Workshop findings only (No repair query required). For correct diagnosis and repair the attached Flowchart must be followed in conjunction with the Measure section of this TPI |
| 2052785/4 | 2020-01-09. Service bulletin. SERVICE BRAKES, HYDRAULIC. Condition: Customer statement: Noise complaint from the braking system. Workshop findings: The noise can be reproduced and clearly assigned to the braking system. Technical Background Brake noises can be attributed to many causes. Eight of the most common causes are: 1. Brake discs or pads are close to their wear limit. 2. New brake pads and/or discs have not been properly bedded in after installation. 3. Aftermarket pads or discs are installed. 4. There is debris such as small stones, grit, road salt or sand between the brake disc and pad. 5. Discs are covered in rust. Rust can form when the vehicle has been stationary for long periods of time (Figure 1). 6. Discs have a groove in them (Figure 2) 7. There is chemical contamination on the braking surface of the disc due to a wheel or tyre cleaner being sprayed directly onto the disc (Figure 3). 8. There are pad marks on the brake disc as a result of the brake pad material transferring to the discs. This can occur when a vehicle has been stood for long periods of time in a wet or snowy environment (Figure 4). |
| 2053177/6 | 2020-01-09. Service bulletin. ENGINE AND ENGINE COOLING; ELECTRICAL SYSTEM. Condition: Customer will not be aware of any fault codes. Workshop may discover spurious fault codes whilst running a Diagnostic Trouble Code (DTC) log as part of other investigations on the vehicle. Technical Background: The attached document contains all of the current known Spurious DTCs for all vehicle variants. Should a particular TPI be listed as Archived within the attached document the TPI can no longer be viewed within Elsa pro, in this case please refer to the instructions with the attached document regarding the DTC description and actions (if any) which should be conducted Service: During routine diagnostic interrogation of vehicle systems use the attached document to determine the course of action to be taken. |
| 2053492/5 | 2020-01-09. Service bulletin. ELECTRICAL SYSTEM; SUSPENSION. Condition: The front and/or rear suspension appears to have dropped. Technical Background: The list of Bentley vehicles below are fitted with air springs as part of the suspension system. Should air leak from the air springs, this will cause the suspension to drop. However, the dropping of the suspension does not necessarily mean that the air spring is faulty. The Measure section of this TPI describes how and where to check for air leaks on the front and rear air springs, the air pump compressor, pipes, valve unit and air reservoirs. This includes potential air leak points on the air springs and also the locations of an air leak that can be repaired without the need to replace an air spring. Please follow and complete the check list within the Measure section of this TPI to help in diagnosing the issue (the check list does not need to be sent as an attachment should a DISS technical query be raised) . Should a leak be found from an air spring, compressor, valve unit or reservoir, please raise a DISS technical query and include as much information as possible including photograph/s of the leak/s location. Once the DISS ticket has been submitted please await clarification from your TSC before commencing with replacing any of the suspected faulty air springs. Mandatory reporting is applicable for all air spring related issues. |
| 2051562/5 | 2020-01-09. Service bulletin. ELECTRICAL SYSTEM. Condition: 12 Volt Battery test instruction Technical Background: For all 12 volt battery issues relating to warranty or a parts warranty claim, a DISS query MUST be raised prior to battery replacement, refer to the instructions within the Measure section of this TPI |
| 2057991/1 | 2020-01-09. Service bulletin. ENGINE AND ENGINE COOLING; ELECTRICAL SYSTEM. Customer statement / workshop findings: Malfunction Indicator Lamp (MIL) illuminated on driver instrument panel. Engine runs unevenly when starting from cold. Camshaft position Diagnostic Trouble Codes (DTCs) stored within Engine Control Unit (ECU). Technical background: When the engine is cold increased friction within the camshaft adjuster unit may result in camshaft position DTCs being stored within the ECU. The concern can be resolved by replacing the camshaft timing gear with a B level part which utilises an internal return spring with higher rate. See Parts information below. There are many possible DTCs related to this failure, the following is a typical example P001200 : A Camshaft position (Bank 1) timing over-retarded. |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.