Service bulletins for the 2022 Bentley Flying Spur
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
657 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
Only bulletins with component: Equipment and accessories are shown. Show all
| 2051045/5 | 2022-03-02. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM. Night vision camera - Washer jet leaking. Customer statement / workshop findings: Washer fluid dripping/leaking from the night vision camera washer jet Technical background: Please note: The photographs shown within this TPI are based on a New Continental GT/C vehicle however the process is similar regardless of vehicle type Referring to Figure 1 - In the event the afore mentioned symptom is evident the operative should refer to the Measure section of this TPI to replace the night vision washer jet (short link hose -Circled) which connects the night vision camera washer jet (A) to the washer jet supply hose connector (B) Measure: 1) Referring to Rep.Gr 63 Remove the front bumper lower inner grilles 2) Disconnect the hose from the night vision camera as shown in Figures 2 and 3 Please note: Washer fluid may leak once the hose is disconnected - Ensure a suitable container is used to collect the fluid, all fluid MUST be discarded as per all local environmental guidelines |
|---|---|
| 2065472/3 | 2022-02-04. Service bulletin. EQUIPMENT; ENGINE AND ENGINE COOLING. V8 Kovomo - New Continental GT/GTC and New Flying Spur - Valve spring replacement (SC21/41) Technical background: The intake valve springs (16) and outlet valve springs (16) located within the cylinder heads of Bank 1 and 2 require replacing The replacement of all valve springs is required due to an issue which was discovered during a routine quality inspection VERY IMPORTANT: Before continuing with the onward instructions the operative should confirm if the symptoms within TPI 2064776/- are applicable In the event the symptoms are applicable the operative MUST first conduct TPI 2064776/- to completion The operative MUST then raise a new Technical DISS query or respond via the already open DISS query and await feedback from Product Support before conducting any further work as further information will be requested back which may change the method of repair Remedy: The replacement of all intake valve springs and all outlet valve springs (Bank 1 and Bank 2) is required |
| 2065472/2 | 2022-01-08. Service bulletin. EQUIPMENT:MECHANICAL. V8 Kovomo - New Continental GT/GTC and New Flying Spur - Valve spring replacement (SC21/41). Technical background: The intake valve springs (16) and outlet valve springs (16) located within the cylinder heads of Bank 1 and 2 require replacing The replacement of all valve springs is required due to an issue which was discovered during a routine quality inspection Remedy: The replacement of all intake valve springs and all outlet valve springs (Bank 1 and Bank 2) is required |
| 2065498/1 | 2022-01-08. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM. Rear seat entertainment - Unavailable features. Customer statement / workshop findings: The crosslink and audio to car functions of the Rear Seat Entertainment screens are not working to specification (icons greyed out) a message is also displayed advising the feature(s) are not available when the icons are pressed Refer to the examples shown in Figures 1,2 and 3. Technical background: The new Rear Seat Entertainment system is being continually improved by Bentley Motors Some features are temporarily unavailable including the crosslink and audio to car these features will be available as an Over The Air update. No workshop visit is required once the updates are available. |
| 2061536/4 | 2022-01-08. Service bulletin. EQUIPMENT:ELECTRICAL:INFOTAINMENT. Infotainment screen stalls at Initialising. Customer statement / workshop findings: Upon start-up of the Infotainment system, the home screen appears to be stuck in the 'Initialising' stage, when this scenario is evident a spinning wheel is visible (Figure 1) Technical background: The issue occurs when the Infotainment system is shut down with the Home menu screen displayed. The Infotainment will start up on this screen the next time the vehicle is started Should the symptoms be the same as the description within the Customer statement/workshop findings section the operative should complete the questionnaire and carry out the instructions within the Measure section of this TPI Once completed the questionnaire should be attached to an existing or already open DISS query |
| 2061537/4 | 2022-01-08. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT. Infotainment home screen - Loading messages visible on start up in multiple tiles. Customer statement / workshop findings: Upon start-up of the Home screen, loading messages can be seen in some or all of the tiles (Figure 1) Technical background: A delay when loading tiles is normal, this is due to the amount of external data that is required to load each individual tile, including multiple pages of external data that can be associated with each individual tile. Some tiles will naturally take longer to load than others. For example, APPS, NAVIGATION and MEDIA are likely to have a greater delay in loading than other tiles this is due to the amount of external data required to display the relevant information. TIP: If required, the delay can be reduced by only selecting tiles that do not communicate with external data sources, for example CAR or CLIMATE functions The operative should complete the questionnaire within the Measure section of this TPI, once completed the questionnaire should be attached to an existing or already open DISS query the operative should await feedback before conducting any further work |
| 2059612/3 | 2022-01-08. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM. Bentayga Hybrid and New Flying Spur Hybrid - Home Charging Unit PIN code. Customer statement / workshop findings: Bentley Home Charging Unit - Unable to recollect Personal Identification Number (PIN). Unable to charge High Voltage Battery with Bentley Home Charging Unit. Technical background: The Bentley Home Charging Unit can be protected from unauthorised use by creating a four-digit PIN. If the PIN authorisation function is activated it has to be entered in the Home Charging Unit before it is used to charge the High Voltage Battery. If a Customer forgets the assigned PIN it will not be possible to unlock the Bentley Home Charging Unit. Follow the steps within the 'Measure' section to reset the PIN. |
| 2065604/1 | 2022-01-06. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT. Suspicion that control units or services have been influenced by third parties. Customer statement / workshop findings: In the event a customer complaint is received relating to a suspicion that control units or services have been influenced by third parties the instructions within this TPI should be followed. Technical background: A suspicion that control units or services have been influenced by third parties means that unauthorised people or groups may have gained access to a vehicle's control unit(s) or online services and may have manipulated them in such a way that may compromise customer data confidentiality or the operation of the vehicle and/or online services. When investigating potential third party influences of control units or online services, it is important to take all normal diagnostic measures to rule out a normal functional error or misuse of the system by the user |
| 2051045/4 | 2022-01-06. Service bulletin. EQUIPMENT; STRUCTURE. Night vision camera - Washer jet leaking. Customer statement / workshop findings: Washer fluid dripping/leaking from the night vision camera washer jet. Technical background: Please note: The photographs shown within this TPI are based on a New Continental GT/C vehicle however the process is similar regardless of vehicle type Referring to Figure 1 - In the event the afore mentioned symptom is evident the operative should refer to the Measure section of this TPI to replace the night vision washer jet (short link hose -Circled) which connects the night vision camera washer jet (A) to the washer jet supply hose connector (B) |
| 2063410/3 | 2022-01-03. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT; EQUIPMENT:ELECTRICAL:INFOTAINMENT. Infotainment Main unit (5F / J794) fault finding/diagnosis procedure. Customer statement / workshop findings Issue suspected with the Infotainment Main unit (5F / J794) - For example: - MMI screen image flickers or goes blank - No response to selection - Audio cuts-out Technical background The operative should continue as follows: - Complete the questionnaire within the Measure section of this TPI (Part 1) once completed the questionnaire should be attached to an existing or already open DISS query - Once the questionnaire is complete, the operative should refer to (Part 2) within the Measure section regarding fault finding/diagnosis of the Infotainment Main unit (5F / J794) |
| 2055580/9 | 2021-12-07. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT. Rotating Display - Fault Diagnosis. Customer statement / workshop findings: Various rotating display operational complaints or noises. Technical background: Follow the Measure section of this TPI that relates to your customer complaint. |
| 2055580/8 | 2021-12-07. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT. Rotating Display - Fault Diagnosis. Customer statement / workshop findings: Various rotating display operational complaints or noises. Technical background: Follow the Measure section of this TPI that relates to your customer complaint. |
| 2064708/1 | 2021-11-05. Service bulletin. EXTERIOR LIGHTING:LIGHTING CONTROL MODULE:SOFTWARE; EQUIPMENT; ELECTRICAL SYSTEM. Customer statement / workshop findings: Unable to set the passenger side exterior mirror memory when reversing (as per the instructions within the owner handbook). Production change: Owner handbooks for later vehicles/models will be revised. Amended owner handbooks or addendums will not be available for this particular issue. |
| 2051526/8 | 2021-11-05. Service bulletin. EQUIPMENT; STRUCTURE; ELECTRICAL SYSTEM. Customer statement / workshop findings: The chrome brightware strip on the veneer face fascia panel of the Bentley Rotating Display (BRD) may appear to be misaligned with the chrome strips on the passenger and drivers side fascia panels. In addition, the gapping and fit between the veneer face fascia panel of the BRD and the passenger and drivers side fascia panels may differ from one side to the other. The minimum functional gaps between the BRD and the passenger/driver fascia and the switch pack if not maintained can impact on the rotational operation of the BRD unit Technical background: The chrome brightware strip is fixed to the veneer face fascia panel with no separate adjustment and as such can appear to be misaligned. The veneer face fascia panel relies on fixed location pins that may be out of tolerance. Rework the veneer face fascia panel to align the chrome brightware strip and/or the gapping between the BRD and the passenger and drivers side fascia panels. |
| 2055580/7 | 2021-11-05. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM; EQUIPMENT:ELECTRICAL:INFOTAINMENT. Customer statement / workshop findings: Various rotating display operational complaints or noises. Technical background: Follow the Measure section of this TPI that relates to your customer complaint. Possible customer complaint. 1. Operational issues 2. Rotating display alignment 3. Grinding noise on operation 4. Rattling noise on operation 5. Squeak/creak on operation 6. Creak/rattle from rotating display whilst driving/uneven operation during rotation |
| 2061343/2 | 2021-10-06. Service bulletin. EQUIPMENT; STRUCTURE. Rear center armrest lid - Poor magnetic retention. Customer statement / workshop findings: Rear center armrest lid has poor magnetic retention to the main armrest, this can lead to a crease in the leather. Technical background: Rear center armrest lid has poor magnetic retention to the main armrest. |
| 2060446/5 | 2021-10-06. Service bulletin. EQUIPMENT; WHEELS; SUSPENSION; STEERING; SERVICE BRAKES, HYDRAULIC. Clicking noise from the front wheels when conducting a static lock to lock steering manoeuvre Customer statement / workshop findings: Clicking noise from the front wheels whilst performing a static lock to lock steering manoeuvre Technical background: Verify that the customer complaint matches the video within the Bentley Hub Reference TPI Transaction number 2060446/- The operative MUST ensure that all similar symptom TPIs are checked to ensure the fault is exactly as described |
| 2060432/3 | 2021-10-06. Service bulletin. ENGINE AND ENGINE COOLING; ELECTRICAL SYSTEM; EQUIPMENT; EQUIPMENT ADAPTIVE/MOBILITY. New Continental GT / GTC and New Flying Spur - Exhaust Flap - Diagnostic Trouble Code Customer statement / workshop findings: Warning lamp illuminated on Driver Instrument Panel (DIP) “Drive system fault. Contact your Bentley dealer displayed on DIP. One or more of the following Diagnostic Trouble Codes (DTCs) stored within Engine Control Modules (ECMs) 1 or 2 (Depending on model type) P04A000: Exhaust Pressure Control Valve P04A000 / P047500: Exhaust Pressure Control Valve A P14AB00: Exhaust door control unit mechanical malfunction P049F00: Exhaust Pressure Control Valve "B |
| 2059246/3 | 2021-10-06. Service bulletin. ELECTRICAL SYSTEM; EXTERIOR LIGHTING; EQUIPMENT; EQUIPMENT ADAPTIVE/MOBILITY. Buzzing/vibration from the left and/or right headlamp and/or DTC's C119C01-C119D01 stored - Matrix beam headlamp only Customer statement: Buzzing noise may be evident from the left and/or right headlamp Workshop findings The following DTCs may also be evident in 00D6 Light control left 2 (Matrix beam) and/or 00D7 Light control right 2 (Matrix beam) C119C01 Fan for headlamp electrical error C119D01 Fan 2 for headlamp electrical error Technical background: Wiring harness routed incorrectly within the headlamp module at the rear of the headlamp, the noise and DTCs are evident due to the harness contacting the headlamp cooling fan |
| 2058516/3 | 2021-10-06. Service bulletin. FUEL SYSTEM, GASOLINE; ENGINE AND ENGINE COOLING; EQUIPMENT. Ticking noise from the rear cabin area Customer statement / workshop findings: Ticking noise can be heard from inside the rear of the cabin when sitting in the rear seats Technical background: The noise can be heard when the engine is at operating temperature, after a drive cycle or an extended idle period, the noise is most evident with the armrest lowered with all electrical consumers switched off. The ticking noise occurs when the purge system is in operation, the vibrations emitted from the purge valve are then amplified through the fuel pipes to the rear of the vehicle. This is normal operation and no further investigation work is required as the vehicle is operating to specification. |
| 2058354/4 | 2021-10-06. Service bulletin. STRUCTURE; EQUIPMENT. New Flying Spur - Flying "B" Mascot Customer statement / workshop findings: This Technical Product Information (TPI) Document is designed to give repair guidance and standardised fault reporting for Flying B functionality, poor finish and damage concerns. |
| 2063953/2 | 2021-10-06. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; ELECTRICAL SYSTEM; FORWARD COLLISION AVOIDANCE. ACC Unavailable - Warning within the DIP - Numerous DTC's within address 003 Customer statement: ACC Unavailable - Warning within the DIP Workshop findings: One or a combination of the following DTCs and symptom codes are evident within address 003 - P191F00 – 4538626 - Pressure sensor for brake booster Electrical malfunction (Front Right Corner Pressure Sensor Fault) - C054100 – 4538624 - Brake Pressure Sensor "B" Range/Performance (Rear left Pressure Sensor Fault) - C054200 – 4538880 - Brake Pressure Sensor "B" Circuit Low (Rear left Pressure Sensor Fault) |
| 2063410/2 | 2021-10-06. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT. Infotainment Main unit (5F / J794) fault finding/diagnosis procedure Customer statement / workshop findings: Issue suspected with the Infotainment Main unit (5F / J794) - For example: -MMI screen image flickers or goes blank - No response to selection - Audio cuts-out Technical background: Refer to the Measure section regarding any Infotainment Main unit (5F / J794) fault finding/diagnosis |
| 2061537/3 | 2021-10-06. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM. Infotainment home screen - Loading messages visible on start up in multiple tiles. Customer statement / workshop findings: Upon start-up of the Home screen, loading messages can be seen in some or all of the tiles. Technical background A delay when loading tiles is normal, this is due to the amount of external data that is required to load each individual tile, including multiple pages of external data that can be associated with each individual tile. Some tiles will naturally take longer to load than others. For example, APPS, NAVIGATION and MEDIA are likely to have a greater delay in loading than other tiles this is due to the amount of external data required to display the relevant information. TIP: If required, the delay can be reduced by only selecting tiles that do not communicate with external data sources, for example CAR or CLIMATE functions. A technical DISS query should be raised by the retailer to highlight the issue described is evident. |
| 2061566/3 | 2021-10-06. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM. Customer statement / workshop findings: VERY IMPORTANT: This TPI is only applicable to vehicles which have the following issues found during the Pre Delivery Inspection (PDI). Unable to complete set-up of Connected Services at PDI and/or the SOS LED in roof console is either lit red or flashing red and/or the test call is unable to complete. |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.