Service bulletins for the 2021 Bentley Continental
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
813 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
| 2051526/4 | 2020-04-03. Service bulletin. STRUCTURE; ELECTRICAL SYSTEM. Rotating screen alignment Customer statement / workshop findings The chrome brightware strip on the veneer face fascia panel of the Bentley Rotating Display (BRD) may appear to be misaligned with the chrome strips on the passenger and drivers side fascia panels. In addition, the gapping and fit between the veneer face fascia panel of the BRD and the passenger and drivers side fascia panels may differ from one side to the other. Technical background The chrome brightware strip is fixed to the veneer face fascia panel with no separate adjustment and as such can appear to be misaligned. The veneer face fascia panel relies on fixed location pins that may be out of tolerance. Rework the veneer face fascia panel to align the chrome brightware strip and/or the gapping between the BRD and the passenger and drivers side fascia panels. |
|---|---|
| 2058176/1 | 2020-02-08. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY. Sun visor mirror cracked Customer statement / workshop findings: Driver or passenger sun visor mirror cracked/broken Technical background: Refer to Measure section of this TPI Measure: A clash can occur with the sun visor and the front seat (folded in forward most position) potentially resulting in a cracked mirror. |
| 2058194/1 | 2020-02-08. Service bulletin. STRUCTURE. Door mirror mounting foot cracked Customer statement / workshop findings Door mirror mounting foot is cracked Technical background In the event the door mirror mounting is cracked, the mounting must be replaced as per the current Repair manual instructions. Please Note: The repair manual instructions will be revised to include the information within the Measure section of this TPI, these instructions MUST be followed until the repair manual is revised. |
| 2058173/1 | 2020-02-08. Service bulletin. ELECTRICAL SYSTEM. Electrical switch replacement guidelines Customer statement / workshop findings: Electrical switch suspected as defective This TPI is not applicable to suspected faulty control units or any component related to the passive restraint system in particular the airbag system Technical background: Prior to replacing an electrical switch refer to the Measure section of this TPI |
| 2050542/4 | 2020-01-09. Service bulletin. EXTERIOR LIGHTING. Customer statement: 1. The lenses of the headlights (illustration 1a) /front fog lamps (illustration 1b) are steamed up/damp from the inside with minor drips. 2. Water is in the headlight (illustration 2a) / front fog lamp (illustration 2b), big drips. Technical Background 1. Damp air settles on the inner lens of the headlights/fog lamps, with recognisable misting in certain weather conditions (comparable with the steaming up of spectacle lenses when entering a warm room in winter or of the bathroom mirror after a shower). 2. Leak on the headlights/front fog lamps. For example through open covers, a damaged seal of the cap or similar. |
| 2056407/2 | 2020-01-09. Service bulletin. STEERING; SUSPENSION. Condition: Customer statement: Noise complaint from the suspension and/or steering Workshop findings: The noise can be reproduced and clearly assigned to the suspension system from either of the axles And/or The noise can be reproduced and clearly assigned to the steering system Prior to starting the instructions within this TPI, the Retailer must check and confirm the vehicle is in standard factory condition and has not had any non-approved aftermarket modifications conducted including the modification of the engine control modules (chip tuning) Check the history of the vehicle to confirm Should any aftermarket modifications be found, the Retailer must make Product Support aware by raising a DISS query to report the details of the modification, you must then await feedback from Product Support before conducting any further work Technical Background It is the retailers responsibility to check and confirm if any TPIs are applicable to the customers complaint/issue, should an applicable TPI be available, apply it and complete a DISS complaint to include Workshop findings only (No repair query required) For correct diagnosis and repair, the attached Flowchart must be followed in conjunction with the Measure section of this TPI |
| 2051187/5 | 2020-01-09. Service bulletin. ELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING. Condition: Poor engine running, reduced power, engine warning lamp illuminated. Technical Background: Technical Product Information (TPI) to assist Retailers when diagnosing poor engine running or misfires. Service: The following TPI should be carried out sequentially to ensure the root cause and analysis of the concern are identified without unnecessary work or repetitive actions taking place. |
| 2056582/2 | 2020-01-09. Service bulletin. STRUCTURE. Condition: Customer statement: Noise complaint from the interior Workshop findings: The noise can be reproduced and clearly assigned to the interior Prior to starting the instructions within this TPI, the Retailer must check and confirm the vehicle is in standard factory condition and has not had any non-approved aftermarket modifications conducted Should any aftermarket modifications be found, the Retailer must make Product Support aware by raising a DISS query to report the details of the modification, you must then await feedback from Product Support before conducting any further work Technical Background It is the retailers responsibility to check and confirm if there are any TPIs which are applicable to the customers complaint/issue if there is an applicable TPI available, apply it and complete a DISS complaint to include Workshop findings only (No repair query required). For correct diagnosis and repair the attached Flowchart must be followed in conjunction with the Measure section of this TPI |
| 2052785/4 | 2020-01-09. Service bulletin. SERVICE BRAKES, HYDRAULIC. Condition: Customer statement: Noise complaint from the braking system. Workshop findings: The noise can be reproduced and clearly assigned to the braking system. Technical Background Brake noises can be attributed to many causes. Eight of the most common causes are: 1. Brake discs or pads are close to their wear limit. 2. New brake pads and/or discs have not been properly bedded in after installation. 3. Aftermarket pads or discs are installed. 4. There is debris such as small stones, grit, road salt or sand between the brake disc and pad. 5. Discs are covered in rust. Rust can form when the vehicle has been stationary for long periods of time (Figure 1). 6. Discs have a groove in them (Figure 2) 7. There is chemical contamination on the braking surface of the disc due to a wheel or tyre cleaner being sprayed directly onto the disc (Figure 3). 8. There are pad marks on the brake disc as a result of the brake pad material transferring to the discs. This can occur when a vehicle has been stood for long periods of time in a wet or snowy environment (Figure 4). |
| 2053492/5 | 2020-01-09. Service bulletin. ELECTRICAL SYSTEM; SUSPENSION. Condition: The front and/or rear suspension appears to have dropped. Technical Background: The list of Bentley vehicles below are fitted with air springs as part of the suspension system. Should air leak from the air springs, this will cause the suspension to drop. However, the dropping of the suspension does not necessarily mean that the air spring is faulty. The Measure section of this TPI describes how and where to check for air leaks on the front and rear air springs, the air pump compressor, pipes, valve unit and air reservoirs. This includes potential air leak points on the air springs and also the locations of an air leak that can be repaired without the need to replace an air spring. Please follow and complete the check list within the Measure section of this TPI to help in diagnosing the issue (the check list does not need to be sent as an attachment should a DISS technical query be raised) . Should a leak be found from an air spring, compressor, valve unit or reservoir, please raise a DISS technical query and include as much information as possible including photograph/s of the leak/s location. Once the DISS ticket has been submitted please await clarification from your TSC before commencing with replacing any of the suspected faulty air springs. Mandatory reporting is applicable for all air spring related issues. |
| 2057841/1 | 2020-01-09. Service bulletin. VISIBILITY. Customer statement / workshop findings: Windscreen cracked/damaged Technical background: Please refer to the instructions within the Measure section of this TPI in the event that a windscreen is cracked/damaged NOTE: The instructions MUST be followed to help the retailer clarify if the windscreen should be replaced under manufacturers warranty (Stress crack) or Customer pay/insurance (external influence damage) Measure: Identification In the event the windscreen is identified as cracked/damaged it is imperative the inspector of the cracked/damaged screen can determine if the crack was caused by external influences (stone chips) OR the screen is cracked/damaged due to a stress crack |
| 2053177/5 | 2020-01-09. Service bulletin. EQUIPMENT. Customer statement / workshop findings: Customer will not be aware of any fault codes. Workshop may discover spurious fault codes whilst running a Diagnostic Trouble Code (DTC) log as part of other investigations on the vehicle. Technical background: The attached document contains all of the current known Spurious DTCs for all vehicle variants. Should a particular TPI be listed as Archived within the attached document the TPI can no longer be viewed within Elsa pro, in this case please refer to the instructions with the attached document regarding the DTC description and actions (if any) which should be conducted Measure: During routine diagnostic interrogation of vehicle systems use the attached document to determine the course of action to be taken. |
| 2052431/3 | 2019-12-06. Service bulletin. STRUCTURE; EQUIPMENT. Customer statement / workshop findings: Rattle / buzzing noise from Control Unit for Head-Up display - dashboard upper trim panel. Technical background: Several known conditions may cause Rattle / buzzing noise from dashboard upper trim panels. • Relative movement between Control Unit for Head-Up Display and associated Trim Ring – figure 1. • Contact between the dashboard and dashboard upper trim panel. • Head-up Display internal fault |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.