Service bulletins for the 2022 Bentley Bentayga
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
636 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
Only bulletins with component: Electrical system are shown. Show all
| 2064680/1 | 2021-11-06. Service bulletin. POWER TRAIN; ELECTRICAL SYSTEM. DTC P060600 evident within address 51 - Electric drive Control unit. Customer statement / workshop findings: High voltage system warning within the DIP Workshop findings: Power Electronics DTC P060600 evident within address 51 - Electric drive Control unit (DTC cannot be cleared) Technical background: DTC P060600 relates to an Active discharge counter error within address 51 (DTC cannot be cleared) In the event the symptoms are as described, conduct the instructions within the Measure section to completion noting the following: IMPORTANT: There are separate SVM codes and MUST be strictly applied as instructed - 4V051SW01 (MUST BE APPLIED FIRST) - 4V0EDU01 (MUST BE APPLIED SECOND) |
|---|---|
| 2064776/1 | 2021-11-05. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL; ENGINE AND ENGINE COOLING; ELECTRICAL SYSTEM. Customer statement / workshop findings -Engine misfiring -Engine running rough (not refined) -Engine misfire DTCs evident -Engine management light illuminated within the DIP -Knocking noise from the cylinder head (NOTE: The noise can be evident on either bank) IMPORTANT: The symptoms described are typically evident during early life stages of vehicle use (between 100Km and 250Km) |
| 2064519/1 | 2021-11-05. Service bulletin. PARKING BRAKE; SERVICE BRAKES, ELECTRIC; ELECTRICAL SYSTEM. DTC's C10BCF6 - 160000 and/or C12E2F2 with symptom code 59744 stored in address 0003 - Parking brake warning in DIP. Customer statement: Parking brake warning light evident within the DIP (See example shown in Figure 1) Workshop findings: C10BCF6 - 160000 - Left parking brake motor Engine speed implausible OR C12E2F2 - 159744 - Right parking brake motor Engine speed implausible. |
| 2064680/2 | 2021-11-05. Service bulletin. EQUIPMENT; EQUIPMENT:ELECTRICAL; ELECTRICAL SYSTEM. Customer statement: High voltage system warning within the DIP. Workshop findings: DTC P060600 with symptom code 29313 is evident within address 51 - Electric drive Control unit (DTC cannot be cleared). Technical background: DTC P060600 with symptom code 29313 relates to an Active discharge counter error within address 51 (DTC cannot be cleared) In the event the symptoms are as described, conduct the instructions within the Measure section to completion noting the following: IMPORTANT: There are separate SVM codes and MUST be strictly applied as instructed: -4V051SW01 (MUST BE APPLIED FIRST) -4V0EDU01 (MUST BE APPLIED SECOND) |
| 2064648/1 | 2021-11-04. Service bulletin. ELECTRICAL SYSTEM; FORWARD COLLISION AVOIDANCE. ACC Unavailable-Traffic Assist Failure-Safeguard Failure-Radar Malfunction Warning DIP - Numerous DTCs within 0013. Customer statement: One or numerous of the following issues are evident: - ACC Failure - Traffic Assist Failure - Safeguard Failure - Radar Malfunction Workshop findings One or a combination of the following DTCs and symptom codes are evident within address 0013 -B200FF0 with Symptom code 1367 or 1313 - Internal Malfunction |
| 2051562/8 | 2021-11-04. Service bulletin. ELECTRICAL SYSTEM. 12 Volt - Battery condition checks. Customer statement / workshop findings: 12 Volt Battery test instruction Technical background: For all 12 volt battery issues relating to warranty or a parts warranty claim, a DISS query MUST be raised prior to battery replacement, refer to the instructions within the Measure section of this TPI |
| 2061582/5 | 2021-11-04. Service bulletin. LATCHES/LOCKS/LINKAGES; ELECTRICAL SYSTEM. Driver/Passenger door/s creak on close. Customer statement / workshop findings: Driver and/or Passenger door creak during the Close function Technical background: Ensure the fault is as described within the Customer statement, refer to the video on the Bentley Hub referencing TPI 2061582/- In the event the symptom is as shown the instructions within the Measure section should be followed. |
| 2064469/1 | 2021-10-07. Service bulletin. STRUCTURE; ELECTRICAL SYSTEM. Bentayga - Rear Window Blinds Do Not Fully Retract. Customer statement / workshop findings: Rear window blind/s do not fully retract (Jammed) |
| 2054599/8 | 2021-10-07. Service bulletin. ELECTRICAL SYSTEM; EXTERIOR LIGHTING. Customer statement / workshop findings: Headlamp operation issues Technical background: DTCs evident within the left light control unit (Diagnostic address D6) and/or the right light control unit (Diagnostic address D7) There are numerous static and intermittent DTCs which maybe evident within the previously mentioned control units, ensure all steps within the Measure section are strictly adhered to New Flying Spur (20 - 22 M/Y) and Bentayga (21 - 22 M/Y). In the event that DTCs C119813 Low beam light bulb open circuit or C1198FA Low beam light bulb short circuit are evident in D6 and/or D7. Please refer to and conduct the instructions within the following TPIs New Flying spur - TPI 2063777/- Bentayga applicable to 21 and 22 M/Y only - 2064497/-. For any other issues please refer to the instructions within the Measure section of this TPI. |
| 2064497/1 | 2021-10-07. Service bulletin. ELECTRICAL SYSTEM; EXTERIOR LIGHTING. Bentayga - DTC for Low Beam Light Bulb Open or Short Circuit DTCs C119813 Low beam light bulb open circuit or C1198FA Low beam light bulb short circuit evident in D6 and/or D7. Customer statement: Head lamp low beam not functioning and/or warning within the DIP. Workshop findings: DTCs C119813 Low beam light bulb open circuit active/static and/or C1198FA Low beam light bulb short circuit active/static logged within diagnostic address D6 (light control left) and/or D7 (light control right). Technical background: The DTCs once triggered are unable to be cleared, with the DTCs logged the Headlamp low beam will not operate. In the event the symptoms are as described, conduct the instructions within the Measure section to completion noting the following: -The update to address D6 Must be done first followed by the update to address D. -Regardless of the DTC which is evident or the address in which the DTC/DTCs are evident, both SVM codes MUST be applied. IMPORTANT: There are separate SVM codes for each diagnostic address D6 (light control left) - 4V0D6BA01 (MUST BE APPLIED FIRST). D7 (light control right) - 4V0D7BA01 (MUST BE APPLIED SECOND). |
| 2053429/4 | 2021-10-06. Service bulletin. ELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING. Emission control system lamp illuminated - DTC P044100 evident. Customer statement / workshop findings: Emission control system warning lamp illuminated (Figure 1) within the Driver Information Panel (DIP) in conjunction with DTC - P044100: EVAP Emission Contr.Sys.Incorrect Purge Flow - logged within one or both engine control modules. Technical background: Should DTC P044100: EVAP Emission Contr.Sys.Incorrect Purge Flow be evident (static or intermittent) within one or both Engine control modules please refer to the instructions within the Measure section of this TPI |
| 2052394/14 | 2021-10-06. Service bulletin. ELECTRICAL SYSTEM; LATCHES/LOCKS/LINKAGES. Driver/Passenger door latch creak on close. Condition: Driver or Passenger door creak during the Close function Technical Background: Refer to the vehicle repair history to check and confirm any previous work done regarding door latch replacement noting the following: - Only replace the door latch which is exhibiting the symptom |
| 2057978/5 | 2021-10-06. Service bulletin. ELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING. Engine Lubricating Oil - Replenishment. Customer statement / workshop findings Engine lubricating oil lamp illuminated on driver instrument panel. Engine lubricating oil requires topping up between services. Technical background: In order to provide effective lubrication and cooling of internal engine components, all internal combustion engines consume a certain amount of engine oil. Oil consumption varies from engine to engine and may change significantly over the life of the engine. Typically, engines with specified running-in periods consume more oil during the running-in period, and the oil consumption will stabilize after the running-in period. Refer to the Owners Manual for specific running-in procedures. Under normal conditions, the rate of oil consumption depends on the quality and viscosity of the oil, the RPM at which the engine is operated, ambient temperature and road conditions. Additional factors are the amount of oil dilution from water condensation or fuel residue, and the oxidation level of the oil. Certain driving conditions may negatively influence the rate of oil consumption. This can occur while the vehicle is operated in city driving conditions, for example: stop and go traffic with extended idle periods |
| 2062075/2 | 2021-10-06. Service bulletin. STRUCTURE; EQUIPMENT; ELECTRICAL SYSTEM. Owner's Handbook - Incorrect roof console image shown - Garage Door Opener (GDO) Condition: The Owners Handbook is showing an incorrect roof console image, highlighting the Garage Door Opener (GDO) programming switches for Bentayga 21MY vehicle derivatives NOTE: The (GDO) is an optional feature |
| 2056950/6 | 2021-10-06. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM. Telephone interference Condition: When using a mobile telephone via a Bluetooth connection the audio quality is poor due to interference Technical Background: Customer complaint of poor audio quality due to interference when using a mobile telephone via a Bluetooth connection, the original right hand side (Passenger) microphone should be replaced for an omni-directional microphone, a software update to 5F - Infotainment control unit 1 mustalso be conducted after the replacement microphone is fitted |
| 2060205/3 | 2021-10-06. Service bulletin. ELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING. Engine Cooling System - DTC P218100 - V8 Kovomo Customer statement / workshop findings: Emission Control Lamp illuminated on Driver Instrument Panel. The time to reach the correct engine coolant operating temperature has increased. Diagnostic Trouble Code(DTC) P218100 -Cooling System Performance is stored in the Engine Control Module (ECM), the vehicle warm up time is longer when compared to other vehicles of the same type. Technical background: It is possible for the engine coolant Thermostat to corrode overtime, this corrosion is due to an adverse reaction of the Thermostat material with the engine coolant. The corrosion and subsequent build-up of debris prevents the correct operation of the thermostat when closing, resulting in over cooling. The ECM triggers a DTC when the target engine temperature is outside of the specified parameter. |
| 2063954/3 | 2021-10-06. Service bulletin. ELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING. Engine warning light illuminated within the DIP during acceleration - DTC P029900 evident - W12 TSI only Customer statement: Engine warning light and max engine speed 4000 rpm warning evident within the DIP during acceleration - Warning on DIP first appears when accelerating (During boost) Workshop findings: DTC P029900 evident within the engine control unit/s In the event the afore mentioned symptoms are evident the operative should refer to the onward instructions |
| 2063410/2 | 2021-10-06. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT. Infotainment Main unit (5F / J794) fault finding/diagnosis procedure Customer statement / workshop findings: Issue suspected with the Infotainment Main unit (5F / J794) - For example: -MMI screen image flickers or goes blank - No response to selection - Audio cuts-out Technical background: Refer to the Measure section regarding any Infotainment Main unit (5F / J794) fault finding/diagnosis |
| 2061566/3 | 2021-10-06. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM. Customer statement / workshop findings: VERY IMPORTANT: This TPI is only applicable to vehicles which have the following issues found during the Pre Delivery Inspection (PDI). Unable to complete set-up of Connected Services at PDI and/or the SOS LED in roof console is either lit red or flashing red and/or the test call is unable to complete. |
| 2061757/2 | 2021-10-06. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM. Customer statement: Night vision warning lamp is evident with the Drivers Information Panel (DIP). Workshop findings: DTC - B2000F2: Faulty control module (Symptom code 4102) evident within address 0084 Night vision control module. Technical background: IMPORTANT: In the event that the issue is evident and the vehicle is post the VINs shown below, a DISS query must be raised ensuring the following is attached to the query. -Detailed description in which the issue occurred, for example -Driving on a quiet road with no traffic, conditions were wet, the road had no street lighting. -Clear photographs showing the condition of the night vision camera and night vision camera lens. -Current and up to date ODIS log. However, should the vehicle be prior to the VIN cut off, the operative MUST carry out the instructions within the Measure section of this TPI. New Flying Spur New Continental GT and New Continental GTC (all vehicles from SCBCD13S1KC071068 are to specification). Bentayga (all vehicles from SJAAL14V0KC025622 are to specification). |
| 2053177/16 | 2021-10-05. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL; ELECTRICAL SYSTEM. All Vehicle Variants - Spurious DTC List. Customer statement / workshop findings Customer will not be aware of any fault codes. Workshop may discover spurious fault codes whilst running a Diagnostic Trouble Code (DTC) log as part of other investigations on the vehicle. Technical background The operative should refer to the Bentley Hub referencing TPI 2053177/- The document (loaded onto the Hub) contains all of the current known Spurious DTCs for all vehicle variants. Should a particular TPI be listed as Archived within the attached document the TPI can no longer be viewed within Elsa pro, in this case please refer to the instructions with the document (loaded onto the Hub) regarding the DTC description and actions (if any) which should be conducted |
| 2063729/2 | 2021-10-05. Service bulletin. ELECTRICAL SYSTEM. Fitment of control modules from donor vehicles for test purposes Technical background: If an issue is suspected for one of the control modules listed below: - Onboard supply control unit (J519) - Convenience system central control unit (J393) - Data bus diagnostics interface (J533) - Control unit 1 for Information Electronics (J794) - Control unit in dash panel insert (J285) - Emergency call module control unit (J949) The fitment of donor parts from another vehicle is not advisable and only possible if approved from Product Support via an open DISS query. |
| 2051562/7 | 2021-10-05. Service bulletin. ELECTRICAL SYSTEM:12V/24V/48V BATTERY; ELECTRICAL SYSTEM. 12 Volt - Battery condition checks. Customer statement / workshop findings: 12 Volt Battery test instruction Technical background: For all 12 volt battery issues relating to warranty or a parts warranty claim, a DISS query MUST be raised prior to battery replacement, refer to the instructions within the Measure section of this TPI |
| 2049586/8 | 2021-10-05. Service bulletin. ENGINE AND ENGINE COOLING; ELECTRICAL SYSTEM. Misfiring, W12 TSI - Excessive carbon build up cylinder leakage. Customer statement / workshop findings: Customer statement: Emission control warning signal displayed, engine misfire Workshop findings: Event entries in engine control unit relating to cylinder misfires excessive carbon build up to leading to cylinder leakage and spark plug foul. Technical background: Deviations in the country-specific fuel specifications can lead to carbon deposits on the injectors. If pronounced these deposits can lead to spark plug fouling, cylinder leakage and fouled injectors all influencing combustion in the cylinder. As a result the above event entries are logged in the engine control unit. Measure: - Follow the Misfire best practice TPI 2051187 in order to confirm that the root cause of the misfire is excessive cylinder carbonisation leading to excessive cylinder leakage/fouling |
| 2036678/4 | 2021-10-05. Service bulletin. ELECTRICAL SYSTEM. Speaker Replacement - Diagnostic checks. Customer statement / workshop findings: Audio output from speakers is distorted Technical background: There have been instances where door speakers have been changed under warranty for the complaint of sound distortion, yet when tested by ourselves and the supplier, no fault could be found with the returned unit. Production change: All speakers are subjected to a dynamic test and the individual results recorded for future reference |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.