Service bulletins for the 2017 Bentley Bentayga
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
660 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
| 2062261/3 | 2021-12-03. Service bulletin. SUSPENSION; ELECTRICAL SYSTEM. Bentayga - Air suspension warning light within the DIP - DTCs P089200 - C104707 - C103B13 - Evident within Address 74. Customer statement / workshop findings: Air suspension warning light within the DIP Workshop findings: One or a combination of the DTCs shown below are evident within address 74 - P089200 - Symptom Code 3145792 - TCM Power Relay Sense Circuit Intermittent (Level Control Valves Open Circuit) - C103B13 - 3145909 - Solenoid for level control system Open circuit - C104707 - 3211279 - Level control valves mechanical malfunction Technical background: Refer to the Measure section of this TPI |
|---|---|
| 2058411/4 | 2021-11-06. Service bulletin. SEAT BELTS. Seat belt buckle stop button - Missing, Condition: Seat belt buckle stop button missing Technical Background: The seat belt buckle stop button should be evident as shown in Figure 1. Should the seatbelt be as shown in Figure 2 (Buckle stop button missing OR broken/loose) - Refer to the Measure section of this TPI |
| 2064579/1 | 2021-11-05. Service bulletin. ELECTRICAL SYSTEM; SUSPENSION. Bentayga - DTC C11C613 - Air suspension warning displayed in Driver Instrument Panel. Customer statement / workshop findings: Air suspension system warning displayed in the Driver Instrument Panel (DIP) Workshop findings DTC C11C613 (Symptom Code 3145826) - Valve for rapid filling of air suspension Open circuit stored in the Chassis control unit (Address 74) Technical background: In the event that the afore mentioned symptom(s) are evident please refer to the instructions within the Measure section of this TPI. |
| 2064779/1 | 2021-11-05. Service bulletin. SUSPENSION; STRUCTURE. Customer statement: Creaking/squeak noise from the front suspension. Workshop findings: Defective upper inner lever bush. Technical background Verify that the customer complaint matches the sound file within the Bentley Hub Reference TPI Transaction number 2064779/-. The noise present in the sound file is caused by defective upper inner lever bush/bushes, the noise can appear in the following possible scenario. -When the vehicle is moved with steering input over uneven surfaces (for e.g. a ramp or speed bump). If the customer complaint occurs in any of the above circumstances and the noise can be clearly assigned to the noise within the sound file Refer to the instructions within the Measure section of this TPI. VERY IMPORTANT NOTE FOR HYBRID VEHICLES: -Hybrid vehicles use a High voltage system and MUST only be worked on by suitably qualified personnel. -Please ensure all guidelines within the repair manual are strictly followed before and whilst conducting any work on vehicles with a High voltage system |
| 2064582/1 | 2021-11-05. Service bulletin. SUSPENSION. Vehicle sitting low on one or more corners when static with no relevant DTCs stored. Customer statement / workshop findings - Vehicle sitting low on one or more corners when static - No relevant DTCs are evident Technical background: Refer to the Measure section of this TPI. Measure: 1) Confirm there are no DTCs indicating a fault with the air suspension system or associated systems 2) Refer to the instructions within TPI 2053492/- to confirm that no air leaks or issues relating to the air springs are evident. |
| 2051562/8 | 2021-11-04. Service bulletin. ELECTRICAL SYSTEM. 12 Volt - Battery condition checks. Customer statement / workshop findings: 12 Volt Battery test instruction Technical background: For all 12 volt battery issues relating to warranty or a parts warranty claim, a DISS query MUST be raised prior to battery replacement, refer to the instructions within the Measure section of this TPI |
| 2053492/7 | 2021-10-07. Service bulletin. SUSPENSION. Air spring fault finding. Customer statement / workshop findings: The front and/or rear suspension appears to have dropped. Technical background: The list of Bentley vehicles below are fitted with air springs as part of the suspension system. Should air leak from the air springs, this will cause the suspension to drop. However, the dropping of the suspension does not necessarily mean that the air spring is faulty. The Measure section of this TPI describes how and where to check for air leaks on the front and rear air springs, the air pump compressor, pipes, valve unit and air reservoirs. This includes potential air leak points on the air springs and also the locations of an air leak that can be repaired without the need to replace an air spring. |
| 2064469/1 | 2021-10-07. Service bulletin. STRUCTURE; ELECTRICAL SYSTEM. Bentayga - Rear Window Blinds Do Not Fully Retract. Customer statement / workshop findings: Rear window blind/s do not fully retract (Jammed) |
| 2054599/8 | 2021-10-07. Service bulletin. ELECTRICAL SYSTEM; EXTERIOR LIGHTING. Customer statement / workshop findings: Headlamp operation issues Technical background: DTCs evident within the left light control unit (Diagnostic address D6) and/or the right light control unit (Diagnostic address D7) There are numerous static and intermittent DTCs which maybe evident within the previously mentioned control units, ensure all steps within the Measure section are strictly adhered to New Flying Spur (20 - 22 M/Y) and Bentayga (21 - 22 M/Y). In the event that DTCs C119813 Low beam light bulb open circuit or C1198FA Low beam light bulb short circuit are evident in D6 and/or D7. Please refer to and conduct the instructions within the following TPIs New Flying spur - TPI 2063777/- Bentayga applicable to 21 and 22 M/Y only - 2064497/-. For any other issues please refer to the instructions within the Measure section of this TPI. |
| 2053429/4 | 2021-10-06. Service bulletin. ELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING. Emission control system lamp illuminated - DTC P044100 evident. Customer statement / workshop findings: Emission control system warning lamp illuminated (Figure 1) within the Driver Information Panel (DIP) in conjunction with DTC - P044100: EVAP Emission Contr.Sys.Incorrect Purge Flow - logged within one or both engine control modules. Technical background: Should DTC P044100: EVAP Emission Contr.Sys.Incorrect Purge Flow be evident (static or intermittent) within one or both Engine control modules please refer to the instructions within the Measure section of this TPI |
| 2053351/7 | 2021-10-06. Service bulletin. ENGINE AND ENGINE COOLING; STRUCTURE. Buzzing noise from engine area. Customer statement / workshop findings Workshop findings: Buzzing noise heard at idle from the sump area when the vehicle is elevated on a workshop ramp. The noise cannot be heard from inside the cabin or outside of the vehicle in normal circumstances. Technical background: A buzzing noise can be generated by the oil pump when the engine is running at idle. Measure: Test a comparable vehicle with the same Engine derivative. If the same noise is apparent on the comparable vehicle and no oil pressure warnings or relevant DTCs are stored then the noise can be considered a characteristic of the vehicle and no further action should be taken. |
| 2057978/5 | 2021-10-06. Service bulletin. ELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING. Engine Lubricating Oil - Replenishment. Customer statement / workshop findings Engine lubricating oil lamp illuminated on driver instrument panel. Engine lubricating oil requires topping up between services. Technical background: In order to provide effective lubrication and cooling of internal engine components, all internal combustion engines consume a certain amount of engine oil. Oil consumption varies from engine to engine and may change significantly over the life of the engine. Typically, engines with specified running-in periods consume more oil during the running-in period, and the oil consumption will stabilize after the running-in period. Refer to the Owners Manual for specific running-in procedures. Under normal conditions, the rate of oil consumption depends on the quality and viscosity of the oil, the RPM at which the engine is operated, ambient temperature and road conditions. Additional factors are the amount of oil dilution from water condensation or fuel residue, and the oxidation level of the oil. Certain driving conditions may negatively influence the rate of oil consumption. This can occur while the vehicle is operated in city driving conditions, for example: stop and go traffic with extended idle periods |
| 2063410/2 | 2021-10-06. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT. Infotainment Main unit (5F / J794) fault finding/diagnosis procedure Customer statement / workshop findings: Issue suspected with the Infotainment Main unit (5F / J794) - For example: -MMI screen image flickers or goes blank - No response to selection - Audio cuts-out Technical background: Refer to the Measure section regarding any Infotainment Main unit (5F / J794) fault finding/diagnosis |
| 2057841/3 | 2021-10-06. Service bulletin. VISIBILITY; STRUCTURE. Windscreen replacement criteria whilst under manufacturers warranty Customer statement / workshop findings: Windscreen cracked/damaged Technical background: Please refer to the instructions within the Measure section of this TPI in the event that a windscreen is cracked/damaged NOTE: The instructions MUST be followed to help the retailer clarify if the windscreen should be replaced under manufacturers warranty (Stress crack) or Customer pay/insurance (external influence damage) |
| 2056582/4 | 2021-10-06. Service bulletin. STRUCTURE. Interior trim - Creak and rattle - Noise identification Customer statement: Noise complaint from the interior Workshop findings: The noise can be reproduced and clearly assigned to the interior Prior to starting the instructions within this TPI, the Retailer must check and confirm the vehicle is in standard factory condition and has not had any non-approved aftermarket modifications conducted Should any aftermarket modifications be found, the Retailer must make Product Support aware by raising a DISS query to report the details of the modification, you must then await feedback from Product Support before conducting any further work |
| 2052785/6 | 2021-10-05. Service bulletin. SERVICE BRAKES, HYDRAULIC. Brake noise identification. Customer statement / workshop findings: Noise complaint from the braking system. Workshop findings: The noise can be reproduced and clearly assigned to the braking system. Technical background Brake noises can be attributed to many causes. Eight of the most common causes are: - Brake discs or pads are close to their wear limit. - New brake pads and/or discs have not been properly bedded in after installation. - Aftermarket pads or discs are installed. - There is debris such as small stones, grit, road salt or sand between the brake disc and pad. - Discs are covered in rust. Rust can form when the vehicle has been stationary for long periods of time (Figure 1). |
| 2053177/16 | 2021-10-05. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL; ELECTRICAL SYSTEM. All Vehicle Variants - Spurious DTC List. Customer statement / workshop findings Customer will not be aware of any fault codes. Workshop may discover spurious fault codes whilst running a Diagnostic Trouble Code (DTC) log as part of other investigations on the vehicle. Technical background The operative should refer to the Bentley Hub referencing TPI 2053177/- The document (loaded onto the Hub) contains all of the current known Spurious DTCs for all vehicle variants. Should a particular TPI be listed as Archived within the attached document the TPI can no longer be viewed within Elsa pro, in this case please refer to the instructions with the document (loaded onto the Hub) regarding the DTC description and actions (if any) which should be conducted |
| 2051562/7 | 2021-10-05. Service bulletin. ELECTRICAL SYSTEM:12V/24V/48V BATTERY; ELECTRICAL SYSTEM. 12 Volt - Battery condition checks. Customer statement / workshop findings: 12 Volt Battery test instruction Technical background: For all 12 volt battery issues relating to warranty or a parts warranty claim, a DISS query MUST be raised prior to battery replacement, refer to the instructions within the Measure section of this TPI |
| 2050542/5 | 2021-10-05. Service bulletin. EXTERIOR LIGHTING:FOG LIGHTS; EXTERIOR LIGHTING; EQUIPMENT. Service info: body/equipment: front exterior lighting steamed up/leaks. Customer statement / workshop findings Customer statement: 1. The lenses of the headlights (illustration 1a) /front fog lamps (illustration 1b) are steamed up/damp from the inside with minor drips. or 2. Water is in the headlight (illustration 2a) / front fog lamp (illustration 2b), big drips. Technical background 1. Damp air settles on the inner lens of the headlights/fog lamps, with recognisable misting in certain weather conditions (comparable with the steaming up of spectacle lenses when entering a warm room in winter or of the bathroom mirror after a shower). 2. Leak on the headlights/front fog lamps. For example through open covers, a damaged seal of the cap or similar. |
| 2050334/7 | 2021-10-05. Service bulletin. ENGINE AND ENGINE COOLING. Ticking noise from engine bay. Customer statement / workshop findings: Ticking noise emanating from rear of Bank 1 cylinder head Technical background: Noise from failed vacuum pump. Measure: A specific vacuum pump failure is known to create a ticking noise. This ticking noise, on initial inspection, is easily misinterpreted as a fault in the valve train or fuel injector, when in reality it is more likely to be produced by a defective vacuum pump. Therefore always ensure that this type of noise is identified precisely using a stethoscope. Specifically use the stethoscope to check the vacuum pump located at the rear of Bank 1 cylinder head, when this is found to be the origin of the noise then change the vacuum pump and retest. |
| 2049586/8 | 2021-10-05. Service bulletin. ENGINE AND ENGINE COOLING; ELECTRICAL SYSTEM. Misfiring, W12 TSI - Excessive carbon build up cylinder leakage. Customer statement / workshop findings: Customer statement: Emission control warning signal displayed, engine misfire Workshop findings: Event entries in engine control unit relating to cylinder misfires excessive carbon build up to leading to cylinder leakage and spark plug foul. Technical background: Deviations in the country-specific fuel specifications can lead to carbon deposits on the injectors. If pronounced these deposits can lead to spark plug fouling, cylinder leakage and fouled injectors all influencing combustion in the cylinder. As a result the above event entries are logged in the engine control unit. Measure: - Follow the Misfire best practice TPI 2051187 in order to confirm that the root cause of the misfire is excessive cylinder carbonisation leading to excessive cylinder leakage/fouling |
| 2036678/4 | 2021-10-05. Service bulletin. ELECTRICAL SYSTEM. Speaker Replacement - Diagnostic checks. Customer statement / workshop findings: Audio output from speakers is distorted Technical background: There have been instances where door speakers have been changed under warranty for the complaint of sound distortion, yet when tested by ourselves and the supplier, no fault could be found with the returned unit. Production change: All speakers are subjected to a dynamic test and the individual results recorded for future reference |
| 2051519/9 | 2021-10-05. Service bulletin. VISIBILITY; ELECTRICAL SYSTEM. HVAC operation issues/HVAC Motor defect DTCs logged. Customer statement / workshop findings: HVAC operation issues and HVAC motor defect (DTCs) evident within address 08 Climatronic control unit, the DTCs can be static or sporadic (Intermittent) The Event memory entries (DTCs) shown within the Header data of this TPI are included as examples Technical background: The HVAC motors can become defective causing HVAC operational issues IMPORTANT: The following instructions should only be carried out on receipt of a valid customer complaint Or The operative is conducting EB28 or EB29 and issues are evident |
| 2051219/6 | 2021-10-05. Service bulletin. ENGINE AND ENGINE COOLING; ELECTRICAL SYSTEM. W12 TSI Camshaft Phaser Position Related DTC. Customer statement / workshop findings: Customer reporting Emission Control Warning Indicator displayed. Engine running rough. |
| 2051187/6 | 2021-10-05. Service bulletin. ENGINE AND ENGINE COOLING; ELECTRICAL SYSTEM. Poor Engine Running Complaints (Misfires) Petrol Engines Only. Customer statement / workshop findings: Poor engine running, reduced power, engine warning lamp illuminated. Technical background: Technical Product Information (TPI) to assist Retailers when diagnosing poor engine running or misfire. Measure: The following TPI should be carried out sequentially to ensure the root cause and analysis of the concern are identified without unnecessary work or repetitive actions taking place. |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.